American Standard 2373.821 - Manual

4

6

14

5

SLOT

MOUNTING

SURFACE

Turn off hot and cold water

supplies before beginning.

CAUTION

Insert SPOUT (1) and CABLE CONNECTOR (14) through center hole, making sure

the SPOUT ESCUTCHEON (2) and SEAL WASHER (3) are properly seated.
Assemble RUBBER WASHER (4), BRASS WASHER (5) and LOCKNUT (6) onto SPOUT

SHANK (7) from under side of sink . Make sure SPOUT (1) is centered in the mounting

hole and the slot in the BRASS WASHER (5) faces toward the rear of the sink.

Tighten LOCKNUT (6) firmly. Fig. A.

Tighten LOCKNUT (11) with WRENCH (8) (supplied) to secure VALVE

BODY (13). Repeat above steps for opposite VALVE BODY (13A).

Install LOCKNUT (11) and RUBBER WASHER (12) onto VALVE BODY (13).

From under side of mounting surface, install VALVE BODY (13) through valve

mounting holes. Threads of VALVE BODY (13) should extent at least 5/16

of a inch above mounting surface top. Fig. B. Thread DECK ADAPTER (10)

onto VALVE BODY (13) until snug against internal stop. If necessary, adjust

LOCKNUT (11).

1

1A

Certified to comply with ANSI A112.18.1

Installation

Instr uctions

S p r e a d L a v a t o r y F a u c e t

with the Speed Connect™ Drain

INSTALL SPOUT

INSTALL VALVE BODY

1

2

1

8

10

9

12
11

13

13a

10

9

12

11

3

Place RUBBER RING (9) into DECK ADAPTER (10).

13

5/16'' MIN.

7

Adjustable Wrench

Screwdriver

Channel Locks

Recommended tools

Tubing Cutter

Connect HOT water supply to inlet of left SHANK and COLD

water supply to right SHANK using sealant, appropriate

connectors, and COUPLING NUTS.

Connect 1-1/4” O.D. tailpiece on POP-UP DRAIN to

waste outlet.

Thread TEE BODY (4) to SPOUT SHANK (5).

Thread HOSE CONNECTOR (6, 6A) to VALVE CONNECTIONS (7, 7A).

9

CHECK DRAIN CONNECTIONS

11

10

12

TEST INSTALLED FITTING

With HANDLES (1) in OFF position, turn on WATER

SUPPLIES (2) and check all connections for leaks.

Remove AERATOR (3).

Operate both HANDLES (1) to flush water

lines thoroughly.

Replace AERATOR (3).

Connect water supply to VALVE BODIES (1,1A) with 1/2" IPS FLEXIBLE

SUPPLIES (2) or 3/8" O.D. BULL-NOSE RISERS (3). Use

adjustable wrench to tighten connections. Do not over tighten.

Be careful not to kink copper supply when bending. Use tubing

cutter to cut to proper length.

MAKE WATER SUPPLY AND WASTE CONNECTIONS

NOTE: FLEXIBLE SUPPLIES OR BULL-NOSE RISERS NOT INCLUDED

AND MUST BE PURCHASED SEPARATELY.

1

HOT

COLD

FERRULE

COMPRESSION

NUT

COUPLING

NUT

FLEXIBLE

SUPPLIES

1

1A

3/8 O.D.

BULL-NOSE

RISERS

1/2" PIPE THREAD

3/8 COMPRESSION

CONNECTION

2

3

4

5

HOT

COLD

2

4

2

1

5

“P” TRAP

WASTE

OUTLET

7

6

6A

7A

3

Operate POP-UP KNOB (5) and fill Sink with water. Check

that DRAIN STOPPER (4) makes a good seal and retains

water in Sink. If STOPPER (4) does not seal properly, please

refer to “Troubleshooting Guide” in these instructions.

Release POP-UP KNOB (5) down and check all drain

connections and "P" trap for leaks. Tighten

if necessary.

Thread CABLE CONNECTOR (1) clockwise

onto DRAIN BODY CONNECTION (2) and

hand tighten. Fig. A.

Your new POP-UP DRAIN installation is

now complete. Fig. B.

Note: Tailpeice on pop-up drain is 1-1/4” O.D.

Fig. B.

Fig. A.

ATTACH CABLE CONNECTOR

7

2

1

Operate LIFT KNOB (1) to verify that STOPPER (2) opens and

closes.

Note: If STOPPER (2) does not open and close properly then refer

to the “troubleshooting section” of these instructions.

CHECK OPERATION OF POP-UP

8

Fig. B.

1-1/4” O.D.

Speed Connect™ Drain

Troubleshooting Guide

Disconnect the Cable from the Drain by threading the Cable Connector (1) counter-clockwise. Fig. A.

Look at the area on the Drain Body where the Cable was attached and locate the component labeled

as “Cam” and “Cam Cap” in the illustration. Fig. B.

Use fingers or small screwdriver under either side of the Cam Cap to pry it out from the Drain. Fig. D.

Remove the Cam by pulling it straight out while wiggling gently to loosen the Rubber Seal. Fig. E.

The Stopper can now be removed by lifting it out of the Drain. Fig. F.

CAM

CAM CAP

CABLE ADJUSTMENT PROCEDURE

If sink does not hold water even though Stopper is in the “down” position:

• Follow CABLE ADJUSTMENT PROCEDURE.

If Stopper does not raise up fully or sink drains too slowly:

• Follow CABLE ADJUSTMENT PROCEDURE.

If you need to remove the Stopper:

• Follow STOPPER REMOVAL PROCEDURE.

If you would like the ability to remove your Stopper simply by lifting it out of the drain:

• Follow STOPPER INSTALLATION PROCEDURE for “Unlocked” mode.

Fig. B.

Fig. A.

REMOVE

CAM

Fig. E.

Fig. F.

Disconnect the Cable from the Drain by threading the Cable Connector (1) counter-clockwise. Fig. A.

Look at the area on the Drain Body where the Cable was attached and locate the component labeled as

“Cam” in the illustration. Fig. B.

Use a small screwdriver to rotate the Cam in the clockwise direction as far as it will go. At this point the

Stopper should be in the UP position. Fig. B, C.

Push DOWN on the Lift-Knob to make sure it is fully down. Fig. C.

Re-attach the Cable to the Drain Body Connection (2) by threading the Cable Connector (1) clockwise onto the

Drain Body Connection (2) and hand-tighten. Fig. A.

STOPPER REMOVAL PROCEDURE

STOPPER INSTALLATION PROCEDURE

Locked Mode:

Look at the Plastic Loop at the bottom of the Stopper and notice

that the Loop is on one side of the Stopper. Fig. G.

To install the stopper in “Locked” mode, insert the Stopper into

the Drain so that the Plastic Loop is facing toward the

rear

of the

Sink and the American Standard logo is facing

front

. Rotate

Stopper slightly if necessary so that the Stopper slides all the

way down.Fig. G.

Re-install the Cam into the Drain, rotating the Cam if necessary

to make sure it is fully inserted. Fig. J.

Re-install the Cam Cap, making sure the guide teeth are facing

outward. If the Cam Cap does not “snap” into place, then rotate

the Cam to make sure it is fully inserted. Fig. K.

Re-attach Cable. See “CABLE ADJUSTMENT PROCEDURE” in

Troubling Shooting Guide to complete installation. Stopper will be

in “Locked” mode and not be removable.

Unlocked Mode:

Look at the Plastic Loop at the bottom of the Stopper and notice

that the Loop is on one side of the Stopper. Fig. H.

To install the stopper in “Unlocked” mode, insert the Stopper into

the Drain so that the Plastic Loop is facing toward the

front

of the

Sink and the American Standard logo is facing

rear

. Rotate Stopper

slightly if necessary so that the Stopper slides all the way down.

Fig. H.

Re-install the Cam into the Drain, rotating the Cam if necessary

to make sure it is fully inserted. Fig. J.

Re-install the Cam Cap, making sure the guide teeth are facing

outward. If the Cam Cap does not “snap” into place, then rotate

the Cam to make sure it is fully inserted. Fig. K.

Re-attach Cable. See “CABLE ADJUSTMENT PROCEDURE” in

“Troublingshooting Guide” to complete installation. Stopper will be

in “Unlocked” mode and removable

.

Fig. J.

Fig. K.

INSTALL

CAM CAP

CAM

INSTALL CAM

The Stopper can be installed two ways, “Locked” Mode (Stopper cannot be

removed) or “Unlock” Mode (Stopper is removable).

Unlocked Mode

Fig. A.

Fig. B.

1

2

LOOP TOWARD

FRONT OF SINK

180˚

LOGO

DRAIN

Fig. H.

Locked Mode

(Vandal Proof)

LOGO

DRAIN

Fig. G.

LOOP TOWARD

REAR OF SINK

2

1

RE-ATTACH

DISCONNECT

Fig. D.

REMOVE

CAM CAP

Fig. C.

DOWN

STOPPER

M962246-YYY0A

LIFT ROD

072574-0070A

EXTENSION ROD

066116-YYY0A

DRAIN STOPPER

M961711-0070A

TAILPIECE INSERT

070847-0070A

CLIP

066118-0070A

PIVOT ROD KIT

M953450-YYY0A

COMPLETE

DRAIN ASSEMBLY

070532-0040A

TAILPIECE

066117-YYY0A

2" FLANGE KIT

POP-UP DRAIN ASSEMBLY

BEFORE 01/07

1

7

3

4

5

6

M 9 6 8 3 0 1 R e v. 1 . 3

M 9 6 8 3 0 1 R e v. 1 . 3

M 9 6 8 3 0 1 R e v. 1 . 3

M 9 6 8 3 0 1 R e v. 1 . 3

M 9 6 8 3 0 1 R e v. 1 . 3

M 9 6 8 3 0 1 R e v. 1 . 3

M 9 6 8 3 0 1 R e v. 1 . 3

1

DOWN

WHITE FOAM

GASKET

NOT VISIBLE

DRAIN

FLANGE

Fig. A.

Fig. B.

A911836-0070A

SEAL

W I D E S P R E A D

L AVAT O R Y FA U C E T

M907559-YYY0A

SPOUT ESCUTCHEON

024220-0070A

SUPPLY NUT

M961733-0070A

SPOUT

MOUNTING KIT

M953006-0070A

TEE & HOSE KIT

Replace the "YYY" with

appropriate finish code

994053-0070A

CARTRIDGE

030258-0070A

VALVE MOUNTING KIT

M962247-YYY0A

SPOUT KIT

CHROME

POLISHED NICKEL

BLACKENED BRONZE

POLISHED BRASS

SATIN NICKEL

002

008

068

099

295

066070-YYY0A

AERATOR

M962248-0070A

DECK ADAPTER KIT

A918555-0070A

HANDLE SCREW

M918049-0070A

STEM ADAPTER

M962244-YYY0A

LEVER HANDLE

ASSEMBLY

M962245-YYY0A

CROSS HANDLE

ASSEMBLY

E N F I E L D

E N F I E L D

MODEL NUMBER

2373.801

2373.821

2373.801

2373.821

1

13

14

SERVICE

TO CLEAN SPRAY

Replace SPRAY (5) and operate handles several times

from OFF to ON position. Do not force, handles turn only 90˚.

SPRAY (5) may accumulate dirt causing distorted

and reduced water flow. Unscrew and remove

SPRAY (5) and rinse clean.

2

90°

To change direction of handle rotation,

proceed as follows

:

Turn valve to OFF position.Unthread HANDLE

BASE (1) from DECK ADAPTER (2).

Pull HANDLE ASSEMBLY off VALVE STEM (3).

Remove SPRING CLIP (4). Lift STOP WASHER (5),

turn 90

°

and replace. Replace SPRING CLIP (4).

Find correct position of HANDLE ASSEMBLY by

adjusting male teeth on VALVE STEM (3) to

female teeth in HANDLE.

Thread HANDLE ASSEMBLY onto DECK ADAPTER

(2) until snug against mounting surface.

1

4

3
5

UNTHREAD

HANDLE

ASSEMBLY

INSTALL HANDLES

1

2

4

5

6

3

TOP

Figure "A"

SPLINE END DOWN

Push ADAPTER (1) on VALVE STEM (2), so that the hole of the

ADAPTER (1) without a spline is facing up. See figure "A". Tighten

STEM SCREW (3) to secure ADAPTER (1).

Find correct position of LEVER HANDLE ASSEMBLY (4) or CROSS

HANDE ASSEMBLY (5) by adjusting male teeth on ADAPTER (1) to

female teeth in HANDLE (4, 5).

Thread LEVER HANDLE ASSEMBLY (4) or CROSS HANDE ASSEMBLY

(5) onto DECK ADAPTER (6) until snug against mounting surface.

THREAD ON

TO DECK

ADAPTER

6

POP-UP KNOB (1) must be fully down. Fig. B.

FLANGE GASKET AND POP-UP KNOB

Check DRAIN FLANGE in SINK to ensure that

WHITE FOAM GASKET (3) is fully compressed

and not visible. Fig. A.

Thread FLANGE (1) counter-clockwise and remove

FLANGE (1) and FOAM GASKET (2) from drain

body. Fig. A.
Thread LOCKNUT (3) clock-wise to bottom of

drain body. Push GASKET (4) down against

LOCKNUT (3). Fig. B.

POP-UP DRAIN

Tighten TAILPIECE (4) on DRAIN BODY before

installing DRAIN BODY. Fig. B.

2

4

3

2

TIGHTEN LOCKNUT

1

REMOVE FLANGE

Remove CLEAR PLASTIC COVER (1).

Remove CARDBOARD SPACER (2) from under

DRAIN POP-UP (3).

2

2

3

3

1

1

Tighten LOCKNUT (1) firmly with Adjustable

Wrench or Channel Locks.

INSTALL DRAIN FROM

BELOW FIXTURE

5

From under side of SINK

install DRAIN BODY (1) up

through drain outlet.

Note: No plumber’s putty

or caulk is required.

The CABLE ATTACHMENT

POINT (2) must face towards

the rear of the SINK.

Install FOAM GASKET (3) and

FLANGE (4) onto drain body

from above SINK and tighten

FLANGE (4) firmly.

4

Fig. A.

Fig. B.

Fig. A.

Fig. B.

2

DRAIN

OUTLET

1

3

4

REAR OF SINK

DRAIN

BODY

4

HOT LINE FOR HELP

For toll-free information and answers to your questions, call:

1 (800) 442-1902

Weekdays 8:00 a.m. to 6:00 p.m. EST

IN CANADA 1-800-387-0369 (TORONTO 1-905-306-1093)

Weekdays 8:00 a.m. to 7:00 p.m. EST

P r o d u c t n a m e s l i s t e d h e r e i n a r e t r a d e m a r k s o f A m e r i c a n S t a n d a r d I n c .

© A m e r i c a n S t a n d a r d I n c . 2 0 0 3

IN MEXICO 01-800-839-12-00

M962522-YYY0A

LIFT ROD AND KNOB

Congratulations on purchasing your American Standard

faucet with Speed Connect drain, a feature found only on

American Standard faucets.

*Your new American Standard faucet is designed to work only with the Speed Connect drain.

To ensure that your installation proceeds smoothly-please read these instructions carefully before you begin.

Speed Connect™ Drain*

• Fewer parts, installs in less time

• Never needs adjustment

• Guaranteed to seal properly the first time, every time.

DO: SIMPLY RINSE THE PRODUCT
CLEAN WITH CLEAR WATER.DRY
WITH A SOFT COTTON FLANNEL
CLOTH.

DO NOT: DO NOT CLEAN THE
PRODUCT WITH SOAPS, ACID,
POLISH, ABRASIVES, HARSH
CLEANERS, OR A CLOTH WITH
A COARSE SURFACE.

CARE INSTRUCTIONS:

M962552-0070A

CAM ASSEMBLY

M952430-0070A

CABLE ASSEMBLY

M952425-YYY0A

DRAIN ASSEMBLY

M962544-YYY0A

STOPPER

ASSEMBLY

M962457-YYY0A

FLANGE

ASSEMBLY

M962458-0070A

DRAIN MOUNTING KIT

A919661-0020A

TAILPIECE

M922872-0070A

CAM SEAT INSERT

M913207-0070A

TAILPIECE INSERT

M919660-0020A

6” TAILPIECE

(NOT INCLUDED

WITH FAUCET)