American Standard 2366 - Manual
American Standard 2366 – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 2 – INSTALL WAX SEAL; CAUTION: DO NOT OVERTIGHTEN NUTS; INSTALL TANK; CAUTION: DO NOT OVERTIGHTEN; INSTALL TOILET SEAT
- Page 3 – Specify when ordering.; ITEM
- Page 4 – AMERICAN-STANDARD ONE-YEAR LIMITED WARRANTY; TROUBLESHOOTING GUIDE
INSTALLATION INSTRUCTIONS
CADET 1.6 GPF TWO-PIECE PRESSURE-
ASSISTED TOILETS
- Model 2333 Elongated
- Model 2366 Round Front
- Model 2377 Elongated - 16-1/2" High Bowl
Thank you for selecting American Standard - the benchmark of fine quality for over 100 years. To ensure this
product is installed properly, please read these instructions carefully before you begin. (Certain installations may
require professional help.) Also be sure your installation conforms to local codes.
RECOMMENDED TOOLS AND MATERIALS
Putty Knife
Regular Screwdriver
Adjustable Wrench
Sealant
Tape Measure
Hacksaw
Wax Ring/Gasket
Flexible Supply Tube
Closet Bolts
Carpenters Level
1
REMOVE OLD TOILET
a.
Close toilet supply valve and flush tank completely. Towel or sponge remaining water from tank and bowl.
b.
Disconnect and remove supply line. NOTE:
If replacing valve, first shut off main water supply!
c.
Remove old mounting hardware, remove toilet and plug floor waste opening to prevent escaping sewer gases.
d.
Remove closet bolts from flange and clean away old wax, putty, etc. from base area.
NOTE:
Mounting surface must be clean and level before new toilet is installed!
305mm
(12)
INSTALL CLOSET BOLTS
Install closet bolts in flange channel, turn 90
°
,
and slide into place 6" (152 mm) apart and
parallel to wall.
SAVE FOR FUTURE USE
3
2
DIMENSIONS (Nominal)
NOTE:
Distance from wall to
closet flange centerline (rough-in) must be 12" (305 mm)
minimum.
CLOSET FLANGE
CLOSET BOLTS
7 3 0 4 7 9 - 1 0 0 R e v . A
Saniwares
CAUTION: PRODUCT IS FRAGILE. TO AVOID BREAKAGE AND POSSIBLE INJURY
HANDLE WITH CARE!
NOTE:
For proper operation these products require a minimum of 20 psi line pressure
P r o d u c t n a m e s l i s t e d h e r e i n a r e t r a d e m a r k s o f A m e r i c a n S t a n d a r d I n c .
© A m e r i c a n S t a n d a r d I n c . 2 0 0 4
!
31 (787mm)
REF.
29 (737mm)
REF.
2 9
( 7 3 7 m m )
O R
3 1 - 1 / 2
( 8 0 0 m m )
A D A H E I G H T
3 0 5 m m
( 1 2 )
F I N I S H E D
F L O O R
2 0 3 m m
( 8 )
S U P P L Y
A S
R E Q ' D
*
FINISHED WALL
19-1/2
(495mm)
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
SPONGEWASHER TANK MTG. BOLTS NUT WASHER WAX RING SEALANT 5 4 6 8 7 INSTALL WAX SEAL Invert toilet on floor (cushion to prevent damage), and install wax ring evenly around waste flange (horn), with tapered end of ring facing toilet. Apply a thin bead of sealantaround base flange. INSTALL TOILET ON FL...
9 11 12 10 ADJUSTMENTS The flushometer tank is designed and factory-adjusted to provide a consistent, safe seal depth in the bowl after each flush. Field refill adjustment is not required. The refill has been preset and locked. FLUSH ACTUATOR ADJUSTMENT - The spacing between the bellcrank and flush ...
AMERICAN-STANDARD ONE-YEAR LIMITED WARRANTY If inspection of this American-Standard plumbing product, within one year after its initial installation, confirms that it is defective in materials or workmanship, American-Standard will repair or, at its option, exchange the product for a similar model. ...
