American Standard 2097.012 - Manual
American Standard 2097.012 – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 2 – INSTALL TOILET SEAT; INSTALL TOILET; Back Side
- Page 3 – CARE AND CLEANING; tank. This damage can cause leakage and property damage.; Diagram 1; NEW SAVONA ONE-PIECE TOILET; REPAIR PARTS LIST; FLAPPER; DESCRIPTION
- Page 4 – TROUBLESHOOTING GUIDE; Replace TOP by engaging; For troubleshooting information please contact:; it is a signal you are wasting water because:
RECOMMENDED TOOLS AND MATERIALS
Putty Knife
Regular Screwdriver
Adjustable Wrench
Sealant
Tape Measure
Hacksaw
Wax Ring/Gasket
Flexible Supply Tube
Closet Bolts
Carpenters Level
1
REMOVE OLD TOILET
a. Close toilet supply valve and flush tank completely. Towel or sponge remaining water from tank and bowl.
b. Disconnect and remove supply line. NOTE:
If replacing valve, first shut off main water supply!
c. Remove old mounting hardware, remove toilet and plug floor waste opening to prevent escaping sewer gases.
d. Remove closet bolts from flange and clean away old wax, putty, etc. from base area.
NOTE:
Mounting surface must be clean and level
before
new toilet is installed!
SAVE FOR FUTURE USE
3
2
CLOSET
FLANGE
CLOSET
BOLTS
7 3 0 1 3 8 7 - 1 0 0
A
CAUTION: PRODUCT IS FRAGILE. TO AVOID BREAKAGE AND POSSIBLE INJURY HANDLE WITH CARE!
P r o d u c t n a m e s l i s t e d h e r e i n a r e t r a d e m a r k s o f A S A m e r i c a , I n c .
© A S A m e r i c a , I n c . 2 0 0 9
NOTE:
Pictures may not exactly define contour of china and components.
NEW SAVONA 1.6 GPF ONE-PIECE TOILET
ROUGHING-IN DIMENSIONS:
NOTE:
Distance from wall to closet flange centerline must be as listed below:
5
4
INSTALL WAX SEAL
Invert toilet on floor (cushion to prevent damage), and
install wax ring evenly around waste flange (horn), with
tapered end of ring facing toilet. Apply a thin bead of
sealant around toilet base.
POSITION TOILET ON FLANGE
a. Unplug floor waste opening and install toilet on closet flange so bolts project
through mounting holes.
b. Loosely install retainer washers and nuts. Side of washers marked "THIS
SIDE UP"
must
face up!
WAX RING
SEALANT
WASHER
NUT
FLANGE
BOLT
TH
IS SIDE UP
Model 2097.012
Thank you for selecting American Standard – the benchmark of fine quality for over 100 years. To ensure this product is installed
properly, please read these instructions carefully before you begin. (Certain installations may require professional help.) Also be sure
your installation conforms to local codes.
!
INSTALL CLOSET BOLTS
Install closet bolts in flange channel, turn 90°, and slide
into place 6" (152 mm) apart and parallel to wall.
INSTALLATION INSTRUCTIONS
FINISHED WALL
79mm
(7-1/8)
13mm
(1/2)
23mm
(7/8)
C/L OF SEAT POST
HOLES 140mm
(5-1/2) CTR'S.
305mm
(12)
C/L
C/L OF SUPPLY
AS REQUIRED
FINISHED
FLOOR
176mm
(7)
736mm
(29)
473mm
(18-1/2)
140mm
(5-1/2)
203mm
(8)
343mm
(13-1/2)
305mm
(12)
384mm
(15)
767mm
(30-1/4)
388mm
(15-5/16)
413mm
(16-1/4)
355mm
(14)
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
7 3 0 1 3 8 7 - 1 0 0 6 7 INSTALL TOILET SEAT Install toilet seat in accordance with manufacturer's directions. - 2 - 8a 8b Before continuing, determine the type of water supply connecation you have from the chart below and use the appropriate assembly parts required to properly reconnect the water ...
7 3 0 1 3 8 7 - 1 0 0 9 10 ADJUSTMENTS a. Adjust water level. Water level should be adjusted to level indicated on tank by adjusting float cup. See Step 10 for water level adjustment method. b. If bowl fails to siphon, an adjustment may be required with the lift chain. Simply remove the bead chain f...
7 3 0 1 3 8 7 - 1 0 0 12 ONE YEAR LIMITED WARRANTY This limited warranty applies only to the original purchaser and installation of the products. In the event of a limited warranty claim, proof of purchase will be required - save sales receipt. For this warranty to become effective, the accompanying...
