American Standard 2071.016 - Manual
American Standard 2071.016 – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 2 – INSTALL TOILET; Position toilet squarely to wall and, with a rocking
- Page 3 – CARE AND CLEANING; FLUIDMASTER; TANK COVER; FLAPPER; HERITAGE REPAIR PARTS LIST; DESCRIPTION
- Page 4 – For troubleshooting information please contact:
RECOMMENDED TOOLS AND MATERIALS
Putty Knife
Regular Screwdriver
Adjustable Wrench
Sealant
Tape Measure
Hacksaw
Wax Ring/Gasket
Flexible Supply Tube
Closet Bolts
Carpenters Level
1
REMOVE OLD TOILET
a.
Close toilet supply valve and flush tank completely. Towel or sponge remaining water from tank and bowl.
b.
Disconnect and remove supply line. NOTE:
If replacing valve, first shut off main water supply!
c.
Remove old mounting hardware, remove toilet and plug floor waste opening to prevent escaping sewer gases.
d.
Remove closet bolts from flange and clean away old wax, putty, etc. from base area.
NOTE:
Mounting surface must be clean and level before new toilet is installed!
INSTALL CLOSET BOLTS
Install closet bolts in flange channel, turn 90
°
, and slide
into place 6" (152 mm) apart and parallel to wall.
SAVE FOR FUTURE USE
3
2
CLOSET FLANGE
CLOSET BOLTS
7 3 0 4 4 9 - 1 0 0 R e v . C
12"
(305mm)
Saniwares
CAUTION: PRODUCT IS FRAGILE. TO AVOID BREAKAGE AND POSSIBLE INJURY HANDLE WITH CARE!
P r o d u c t n a m e s l i s t e d h e r e i n a r e t r a d e m a r k s o f A m e r i c a n S t a n d a r d I n c .
© A m e r i c a n S t a n d a r d I n c . 2 0 0 2
!
NOTE:
Pictures may not exactly define contour of china and components.
HERITAGE1.6 GPF ONE-PIECE TOILET
2071.016
ROUGHING-IN DIMENSIONS:
NOTE:
Distance from wall to closet flange centerline must be as listed below:
Thank you for selecting American Standard - the benchmark of fine quality for over 100 years. To ensure this product
is installed properly, please read these instructions carefully before you begin. (Certain installations may require
professional help.) Also be sure your installation conforms to local codes.
INSTALLATION
INSTRUCTIONS
5
4
INSTALL WAX SEAL
Invert toilet on floor (cushion to prevent damage), and
install wax ring evenly around waste flange (horn), with
tapered end of ring facing toilet. Apply a thin bead of
sealant around toilet base.
POSITION TOILET ON FLANGE
a.
Unplug floor waste opening and install toilet on closet flange so bolts project
through mounting holes.
b.
Loosely install retainer washers and nuts. Side of washers marked "THIS
SIDE UP"
must face up!
W A X R I N G
S E A L A N T
F I N I S H E D W A L L
C / L O F O U T L E T
C / L O F S U P P L Y
A S R E Q U I R E D
F I N I S H E D
F L O O R
3 0 "
( 7 6 2 m m )
4 "
( 1 0 2 m m )
1 2 "
( 3 0 5 m m )
1 4 "
( 3 5 6 m m )
2 4 - 1 / 2 "
( 6 2 2 m m )
1 9 - 3 / 4 "
( 5 0 2 m m )
C / L
W A S H E R
N U T
B O L T
MTG. CLIP
F L A N G E
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
7 3 0 4 4 9 - 1 0 0 R e v . C 6 7 INSTALL TOILET a. Position toilet squarely to wall and, with a rocking motion, press bowl down fully on wax ring and flange. Alternately tighten nuts until toilet is firmly seated on floor. CAUTION: DO NOT OVERTIGHTEN NUTS OR BASE MAY BE DAMAGED! b. Install caps on ...
7 3 0 4 4 9 - 1 0 0 R e v . C 9 10 ADJUSTMENTS a. Adjust water level. Water level should be adjusted to level indicated on tank by adjusting float cup. See Step 10 for water level adjustment method b. If bowl fails to siphon, an adjustment may be required with the lift chain. Simply remove the bead ...
7 3 0 4 4 9 - 1 0 0 R e v . C 12 AMERICAN-STANDARD ONE-YEAR LIMITED WARRANTY If inspection of this American-Standard plumbing product, within one year after its initial purchase, confirms that it is defective in materials or workmanship, American-Standard will repair or, at its option, exchange the ...
