American Standard 2000.16X - Manual
American Standard 2000.16X – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 3 – Important: If SUPPLY HOSES
- Page 4 – RED RING HOT
- Page 5 – Speed ConnectTM Drain; Troubleshooting Guide; CABLE ADJUSTMENT PROCEDURE; If Stopper does not raise up fully or sink drains too slowly:; STOPPER REMOVAL PROCEDURE
- Page 6 – STOPPER INSTALLATION PROCEDURE; rear; “Locked”; front; “Unlocked”; Unlocked Mode
COLLAR ON
MOUNTING NUT
8
M 9 6 8 7 6 0 R e v . 1 . 3
Certified to comply with ANSI A112.18.1
I n s t a l l a t i o n
I n s t r u c t i o n s
C e n t e r s e t L a v a t o r y F a u c e t w i t h
Speed Connect™ Drain
Adjustable Wrench
Screwdriver
Channel Locks
Recommended tools
1
2000.10X
2000.16X
T M
2
4
3
1
9
1
INSTALL FAUCET
Turn off hot and cold water
supplies before beginning.
CAUTION
GROOVE
(FAUCET
BASE)
6
4
7
5
Seat SEAL
(1)
into under side of FAUCET BASE
(2)
.
Feed FAUCET SUPPLIES
(3)
, MOUNTING STUD
(4)
and DRAIN
CABLE ASSEMBLY
(8)
through ESCUTCHEON
(9)
(optional) and the
mounting hole of lavatory or mounting surface.
Fig. A.
From below, push GASKET
(7)
and RETAINING WASHER
(5)
onto
MOUNTING STUD
(4)
. Secure Faucet with MOUNTING NUT
(6)
,
pulling faucet to front of sink, so SUPPLIES
(3)
rests against
mounting hole. Before final tightening, make sure collar on
MOUNTING NUT
(6)
is seated into RETAINING WASHER
(5)
.
Fig.B.
Adjust Faucet so that it is centered. Tighten MOUNTING NUT
(6)
to complete faucet mounting.
Fig.
B.
Fig.
A.
Congratulations on purchasing your American Standard
faucet with Speed Connect drain, a feature found only on
American Standard faucets.
*Your new American Standard faucet is designed to work only with the Speed Connect drain. Heplful tips for
removing your current drain can be found in the Troubleshooting section of these instructions.
To ensure that your installation proceeds smoothly-please read these instructions carefully before you begin.
Speed Connect™ Drain*
• Fewer parts, installs in less time
• Never needs adjustment
• Guaranteed to seal properly the first time, every time.
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
CHECK OPERATION OF POP-UP 8 MAKE WATER SUPPLY AND WASTE CONNECTIONS 9 Thread CABLE CONNECTOR (1) clockwise onto DRAIN BODY CONNECTION (2) and hand tighten. Fig. A. Your new POP-UP DRAIN installation isnow complete. Fig. B. Note: Tailpeice on pop-up drain is 1-1/4” O.D. Fig. B. Fig. A. ATTACH CABLE C...
2 SERVICE TEST INSTALLED FITTING With HANDLE (1) in OFF position, turn on WATER SUPPLIES (2) and check all connections for leaks. Remove AERATOR (3) . Operate HANDLE (1) to flush water lines thoroughly. Replace AERATOR (3) . 5 2 CHECK DRAIN CONNECTIONS Operate POP-UP KNOB (4) and fill lavatory with ...
M 9 6 8 7 6 0 R e v . 1 . 3 Speed Connect™ Drain Troubleshooting Guide Disconnect the Cable from the Drain by threading the Cable Connector (1) counter-clockwise. Fig. A. Look at the area on the Drain Body where the Cable was attached and locate the component labeled as “Cam” and “Cam Cap” in the ...
