American Standard 1480.115 - Manual
American Standard 1480.115 – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 2 – DRAIN
- Page 3 – NOTE: FLEXIBLE SUPPLIES OR BULL-NOSE RISERS MUST BE; HOT
- Page 4 – PRY RED RING FORWARD; LIMIT SAFETY STOP
M 9 6 8 3 0 5 R E V. 1 . 1
1480.110
1480.115
S E VA
Certified to comply with ANSI A112.18.1
Installation
Instr uctions
C e n t e r s e t L a v a t o r y F a u c e t w i t h
SpeedConnect™ Drain
Adjustable Wrench
Screwdriver
Channel Locks
Required tools
Tubing Cutter
1
INSTALL FAUCET
SINK OR
MOUNTING
SURFACE
POP-UP
CABLE
Turn off hot and cold water supplies before beginning.
Note: Putty is not required unless mounting surface
is uneven.
Apply a bead of PUTTY along the edge of
the underside of the BODY
(1)
if required.
Insert FAUCET
(1)
and CABLE CONNECTOR
(2)
through
mounting holes of Sink or mounting surface.
Fig.
A.
Assemble LOCKNUTS
(3)
onto SHANKS
(4)
from under
side of Sink. Hand tighten firmly.
Fig.
B.
2
2
4
3
3
4
1
(HAND TIGHTEN)
Fig.
A.
Fig.
B.
1
PUTTY
(IF REQUIRED)
0
1
2
3
4
5
6
7
Congratulations on purchasing your American Standard
faucet with Speed Connect drain, a feature found only on
American Standard faucets.
*Your new American Standard faucet is designed to work only with the Speed Connect drain. Heplful tips for
removing your current drain can be found in the Troubleshooting section of these instructions.
To ensure that your installation proceeds smoothly-please read these instructions carefully before you begin.
Speed Connect™ Drain*
• Fewer parts, installs in less time
• Never needs adjustment
• Guaranteed to seal properly the first time, every time.
Turn off water at
main supply.
CAUTION
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
M 9 6 8 3 0 5 R E V. 1 . 1 Thread FLANGE (1) counter-clockwise and remove FLANGE (1) and FOAM GASKET (2) from drain body. Fig. A. Thread LOCKNUT (3) clock-wise to bottom of drain body. Push GASKET (4) down against LOCKNUT (3). Fig. B. POP-UP DRAIN Tighten TAILPIECE (4) on DRAIN BODY before installin...
M 9 6 8 3 0 5 R E V. 1 . 1 COMPRESSION NUT 3/8” COMPRESSION CONNECTION COUPLING NUT FLEXIBLE SUPPLIES 3/8 O.D. BULL-NOSE RISERS Operate LIFT KNOB (1) to verify that STOPPER (2) opens and closes. Note: If STOPPER (2) does not open and close properly then refer to the “troubleshooting section” of thes...
M 9 6 8 3 0 5 R E V. 1 . 1 2 1 4 SERVICE 10 TEST INSTALLED FITTING With HANDLE (1) in OFF position, turn on WATER SUPPLIES (2) and check all connections for leaks. Remove AERATOR (3) . Operate both HANDLE (1) to flush water lines thoroughly. Replace AERATOR (3) . 5 2 CHECK DRAIN CONNECTIONS Operate ...
