American Standard 1340.855 - Manual
American Standard 1340.855 – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 2 – COLD; HOT; COUPLING NUT
- Page 3 – CLOCKWISE; Turn on water supplies and check connections for leaks.; TEST INSTALLED FITTING; PRESS HANDLE; REMOVE REPLACE
- Page 4 – M E T E R I N G; C e n t e r S e t F a u c e t s; CHROME; PRODUCT NUMBERS
Certified to comply with ANSI A112.18.1M
SPOUT RECESS
Turn off hot and cold water
supplies before beginning.
CAUTION
Assemble RUBBER WASHER (5) and BRASS WASHER (6) and
LOCKNUT (7) onto SPOUT SHANK (4). Align SPOUT ASSEMBLY.
From underside of ledge, tighten LOCKNUT (7) to secure SPOUT
ASSEMBLY to mounting surface.
!
SPOUT ASSEMBLY
PREPARE TUBE AND TEE ASSEMBLY
2
3
1
1
2
1
3
5
6
1340.725
1340.825
1340.855
1340.865
Remove COUPLING NUT (1) and FERRULE (2) from each
VALVE (3) and slide onto TUBING (4).
8"
2
7
4
MOUNTING
SURFACE
NOTE; Washer (5) may remain
inside of Actuator Assembly.
SPOUT
ASSEMBLY
MOUNTING
SURFACE
S P R E A D L A V A T O R Y
F A U C E T S
I n s t a l l a t i o n
I n s t r u c t i o n s
Thank you for selecting American-Standard...the
benchmark of fine quality for over 100 years.
To ensure that your installation proceeds smoothly--please
read these instructions carefully before you begin.
Install RING WASHER (1) into SPOUT (2) recess. Check
that O-RING (3) on end of SPOUT SHANK (4) is in place. Insert
SPOUT SHANK (4) into center hole on mounting surface.
M E T E R I N G
4
1340.725
1340.825
1340.855
1340.865
Plumbers' Putty or Caulking
Adjustable Wrench
2.5mm Hex Wrench
Channel Locks
TOOLS REQUIRED
REMOVE REPLACE
Remove HANDLE (1) by
removing INDEX BUTTON (2)
and SET SCREW (3) with a
2.5mm hex wrench.
Pull off HANDLE (1).
Remove ACTUATOR
ASSEMBLY (4).
Remove WASHER (5).
REMOVE HANDLE AND
ACTUATOR ASSEMBLY
1
4
5
2
3
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
M 9 6 8 4 9 2 9 2 4 5/16'' MIN. MOUNTINGSURFACE 10 11 11 10 1 3 " Push TUBING (14) ends into VALVE (4) side outlets. Insert VALVES (4)into mounting holes from underside of ledge. Press TEE (5) onto SPOUT SHANK (6) making certain that the O-RING (7) isproperly seated on SHANK (6). Push COUPLING (...
M 9 6 8 4 9 2 # INSTALL HANDLES Remove INDEX BUTTON (1; 2) and loosen SETSCREW (3) with a 2.5mm hex wrench. Install HANDLES (4) onto VALVE STEM (5). Tighten SET SCREWS (3) with 2.5mm Hex Wrench. Replace INDEX BUTTONS. Red (1) in Left HANDLE (4)Blue (2) in Right HANDLE (4). 1 1 4 3 2.5mmHEX WRENCH 3 ...
M 9 6 8 4 9 2 M E T E R I N G C e n t e r S e t F a u c e t s CHROME 002 Replace the "YYY" withappropriate finish code HOT LINE FOR HELP For toll-free information and answers to your questions, call: 1 (800) 442-1902 Weekdays 8:00 a.m. to 8:00 p.m. EST IN CANADA 1-800-387-0369 (TORONTO 1-905...
