American Standard 0155.017 - Manual
American Standard 0155.017 – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
H162
© 2008 AS America Inc.
NOTES:
0153.015 LEFT HAND OUTLET (SHOWN).
0155.017 RIGHT HAND OUTLET (REVERSE DIMENSIONS).
REFER TO INSTALLATION INSTRUCTIONS SUPPLIED WITH BATH FOR
ADDITIONAL INFORMATION.
SHOWN WITH POP-UP C.D. & O.
FITTINGS NOT INCLUDED AND MUST BE ORDERED SEPARATELY.
CONCEALED PIPING NOT INCLUDED.
IMPORTANT: Dimensions of fixtures are nominal and may vary within the range
of tolerances established by ANSI Standard A112.19.4. These measurements
are subject to change or cancellation. No responsibility is assumed for use of
superseded or voided leaflet.
To Be Specified:
❏
Color:
❏
Bath Faucet*:
❏
Faucet Finish:
❏
Drain: 1583.470
* See faucet section for additional models available
SALEM 14™
RECESS BATH
ENAMELED STEEL
SALEM 14™ RECESS BATH
❏
0155.017 Right hand outlet
❏
0153.015 Left hand outlet
Product Features:
• Acid resisting, heavy gauge, enameled
steel one-piece recess bath
• Integral apron
• End drain outlet
• Slip-resistant surface
• Straight tiling bead
• Fully-bonded support pad
Nominal Dimensions:
1524 x 762 x 356mm
(60" x 30" x 14")
Bathing Well Dimensions:
1346 x 610 x 337mm
(53" x 24" x 13-1/4")
Compliance Certifications -
Meets or Exceeds the Following Specifications:
• ASME A112.19.4 for Enameled Steel Plumbing
Fixtures
• ASTM F-462 for Slip-resistant Bathing Facilities
Revised 2/08
MEETS THE AMERICANS WITH DISABILITIES ACT GUIDELINES
AND ANSI A117.1 REQUIREMENTS FOR ACCESSIBLE AND
USEABLE BUILDING FACILITIES-CHECK LOCAL CODES.
INSTALL WITH SEAT AT HEAD END.
762mm
(30)
1524mm
(60)
19mm
(3/4)
19mm
(3/4)
365mm
(14-3/8)
197mm
(7-3/4)
13mm
(1/2)
305mm
(12)
102 (4)
102
(4)
102mm
(8)
356mm
(14)
229 x 305mm
(9 x 12") CUTOUT
FINISHED
WALL
1-1/2 N.P.T.M. THREADS
1-1/2 O.D. TAILPIECE
C/L OF VALVES
(44mm [1-3/4"]
DIA. HOLES)
SPOUT
1/2" S.P.S.
ROUGH
FLOOR
PLUMBER NOTE:
PROVIDE SUITABLE FULL LENGTH
SUPPORT AT THIS POINT.
OPTIONAL TO FINISHED TO FINISHED
FLOOR (USUALLY BETWEEN 1651 to
1981mm ( 65" & 78')
C/L OF SHOWER CURTAIN ROD
(USUALLY 1930mm (76")
FROM FIN. FLOOR)
1/2 S.P.S. OR 1/2"
C.W.T. SUPPLIES
FINISHED
WALL
FINISHED
WALL
C/L OF DRAIN
SHOWER 1/2" S.P.S.
NOTE: NO CONCEALED
PIPING FURNISHED
SUMP PAD
711mm
(28)
203mm
(8)
76mm
(3)
BARRIER FREE
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
