Page 3 - iii; K T - 4 0 0 E t h e r n e t F o u r - D o o r C o n tr o l l e r I n s t a l l a t i o n M a n u a l; Table of Contents
D N 1 7 2 6 - 0 8 11 iii K T - 4 0 0 E t h e r n e t F o u r - D o o r C o n tr o l l e r I n s t a l l a t i o n M a n u a l Table of Contents Pre-Installation Information ......................................................................................................................... 1 Cop...
Page 4 - iv
D N 1 7 2 6 - 0 8 11 iv Configuring the KT-400 Ethernet Four-Door Controller with the KT-Finder .............................................. 33Installation Checklist ................................................................................................................................. 37...
Page 5 - Pre-Installation Information; Important: NEVER INSTALL THE EQUIPMENT DURING A LIGHTNING STORM!; must be as shown within the included diagram, or equivalent.
D N 1 7 2 6 - 0 8 11 1 K T - 4 0 0 E t h e r n e t F o u r - D o o r C o n tr o l l e r I n s t a l l a t i o n M a n u a l Pre-Installation Information To the Installer: If you are familiar with the installation, you can use the installation checklist on page 37 with the symbol . Copyright Informat...
Page 6 - Technical Support; Phone Numbers
D N 1 7 2 6 - 0 8 11 2 Technical Support For technical assistance with the KT-400 Ethernet Four-Door Controller and other Kantech products, contact technical support, Monday to Friday. See the following table for the technical support phone numbers. Country/Region Phone Numbers Support Hours Email N...
Page 7 - Compliance Specifications; Hammond BF2F; UL 294 Compliance Notice; Note
D N 1 7 2 6 - 0 8 11 3 K T - 4 0 0 E t h e r n e t F o u r - D o o r C o n tr o l l e r I n s t a l l a t i o n M a n u a l Compliance Specifications FCC & IC Compliance This device complies with Part 15 of the FCC rules Class A. Operation is subject to the following two conditions: (1) this dev...
Page 8 - KT-NCC Installation Manual
D N 1 7 2 6 - 0 8 11 4 • 1 GB RAM • Minimum free hard disk space: 20 GB • Color depth: 24-bit (16 million colors), required for Video Integration only • Screen resolution: 1024 x 768 • Graphic adapter card: 32 MB • 48X CD-ROM drive • Network Interface card: 10/100 Base-T network adaptor Note: Actual...
Page 9 - Overview; Multiple Configuration Options; Web Configuration Page:; Four Onboard doors; Figure 1; Communication Ports
D N 1 7 2 6 - 0 8 11 5 K T - 4 0 0 E t h e r n e t F o u r - D o o r C o n tr o l l e r I n s t a l l a t i o n M a n u a l Overview The KT-400 Ethernet Four-Door Controller is designed to meet the highest standards of access control and point monitoring applications. Here are the features of the KT...
Page 11 - Built-in SPI Expansion
D N 1 7 2 6 - 0 8 11 7 K T - 4 0 0 E t h e r n e t F o u r - D o o r C o n tr o l l e r I n s t a l l a t i o n M a n u a l Downloadable Firmware The firmware program can be downloaded from any EntraPass workstation to the KT-400 Ethernet Four-Door Controller. The firmware program, stored in the con...
Page 14 - Figure 3: KT-400 Cabinet Model for North America
D N 1 7 2 6 - 0 8 11 10 Figure 3: KT-400 Cabinet Model for North America
Page 15 - System Architecture; Over the internet. See; Figure 4; Application with EntraPass Global Edition and a Global Gateway.; Figure 6; Application with EntraPass Global Edition and a KT-NCC.; Figure 7
D N 1 7 2 6 - 0 8 11 11 K T - 4 0 0 E t h e r n e t F o u r - D o o r C o n tr o l l e r I n s t a l l a t i o n M a n u a l System Architecture The KT-400 Ethernet Four-Door Controller can be used through various site applications with EntraPass Special Edition, EntraPass Corporate Edition and Entr...
Page 17 - Figure 8: Over RS-232 straight from the EntraPass RS-232 COM port
D N 1 7 2 6 - 0 8 11 13 K T - 4 0 0 E t h e r n e t F o u r - D o o r C o n tr o l l e r I n s t a l l a t i o n M a n u a l Figure 7: Over the internet with a KT-NCC and EntraPass Global Edition Figure 8: Over RS-232 straight from the EntraPass RS-232 COM port
Page 18 - VITAL LED Heartbeat Patterns; . This information is particularly useful when connecting the; Table 1: VITAL LED Heartbeat Patterns
D N 1 7 2 6 - 0 8 11 14 VITAL LED Heartbeat Patterns Communication status and other vital controller parameters can be obtained from VITAL LED heartbeat patterns. It is located near the RS-232 port (COM3), see Figure 1 . This information is particularly useful when connecting the controller to the r...
Page 19 - Technical Specifications; Type
D N 1 7 2 6 - 0 8 11 15 K T - 4 0 0 E t h e r n e t F o u r - D o o r C o n tr o l l e r I n s t a l l a t i o n M a n u a l Technical Specifications Type Description Power input ( KT-400 ) Transformer class 2, IN 120 VAC; OUT 16 VAC, 75 VA Battery back-up ( KT-BATT-12 ) 12 VDC, 7 Ah battery supervi...
Page 20 - Electrical Specifications
D N 1 7 2 6 - 0 8 11 16 Electrical Specifications KT-400 Ethernet Four-Door Controller Models, Expansion Modules Models, Related Documentation and Miscellaneous Items OPEN COLLECTOR OUTPUTS MAXIMUM CURRENT (Typical) COMBINED MAXIMUM CURRENT LEDs (LED, OUT1 and OUT2) for each door reader 25 mA (each)...
Page 21 - Dimensions Drawings
D N 1 7 2 6 - 0 8 11 17 K T - 4 0 0 E t h e r n e t F o u r - D o o r C o n tr o l l e r I n s t a l l a t i o n M a n u a l DN1475 EntraPass Special Edition, Reference Manual - Spanish version DN1436 EntraPass Corporate Edition, Reference Manual - Spanish version DN1599 EntraPass Global Edition, Re...
Page 22 - Models Information; Table 2: Models Bills of Material
D N 1 7 2 6 - 0 8 11 18 Models Information • KT-400 : Cabinet with one KT-400 for North America, up to three expansion modules can be installed in the cabinet, • KT-400-PCB : KT-400 with parts, • KT-400-ACC : Accessory kit, • KT-400-CAB : Cabinet only for North America, Table 2: Models Bills of Mate...
Page 23 - Installing the KT-400 Ethernet Four-Door Controller
D N 1 7 2 6 - 0 8 11 19 K T - 4 0 0 E t h e r n e t F o u r - D o o r C o n tr o l l e r I n s t a l l a t i o n M a n u a l Installing the KT-400 Ethernet Four-Door Controller Preparing to Install the KT-400 Ethernet Four-Door Controller Required to install KT-400 Ethernet Four-Door Controller • Fo...
Page 25 - terminals are not
D N 1 7 2 6 - 0 8 11 21 K T - 4 0 0 E t h e r n e t F o u r - D o o r C o n tr o l l e r I n s t a l l a t i o n M a n u a l Relay Controlled Outputs The KT-400 provides four relay outputs RELAY1 to RELAY4 (3 Amps, 30 VAC/VDC). The KT-400 can be expanded up to 256 controlled outputs when using expan...
Page 26 - Connecting the KT-400 Ethernet Four-Door Controller
D N 1 7 2 6 - 0 8 11 22 Connecting the KT-400 Ethernet Four-Door Controller Connecting the VC-485 or the USB-485 to the RS-485 Bus Connect the RS-485 cable to (COM1) + 485 - and the RS-485 signal ground to the 12 VDC AUX - (negative) Controllers are linked together through their RS-485 terminals. Th...
Page 27 - Connecting the Master Controller to the Host PC via RS-232; The; Powering the KT-400 Ethernet Four-Door Controller; Place battery in cabinet; for VITAL LED behavior identifications.
D N 1 7 2 6 - 0 8 11 23 K T - 4 0 0 E t h e r n e t F o u r - D o o r C o n tr o l l e r I n s t a l l a t i o n M a n u a l Connecting the Master Controller to the Host PC via RS-232 Connect RS-232 cable from KT-400 to the PC (maximum length 30 m (100 ft)) If the local master controller is located ...
Page 28 - SPI Expansion Port; Figure 9; and; Figure 9: KT-400 Interconnection Examples with Expansion Modules; Check the following table to calculate the SPI chain current draw:; Example of current draw calculation:; Expansion Module; Maximum current draw from KT-400 SPI expansion port; when the 12 VDC AUX terminals are not used
D N 1 7 2 6 - 0 8 11 24 SPI Expansion Port The SPI (Serial Peripheral Interface) expansion port on the KT-400 is used to connect expansion modules, in order to add more inputs and outputs such as relays. The maximum current draw for the SPI expansion port is 500 mA when the 12V AUX terminals are not...
Page 29 - Important Installation Rules about Expansion Modules; must be calculate each time; Part number
D N 1 7 2 6 - 0 8 11 25 K T - 4 0 0 E t h e r n e t F o u r - D o o r C o n tr o l l e r I n s t a l l a t i o n M a n u a l Important Installation Rules about Expansion Modules Note 1: The maximum current draw must be calculate each time there is a new module added to the SPI chain. Rule 2: The SPI...
Page 30 - Figure 10: PCB View of Expansion Modules
D N 1 7 2 6 - 0 8 11 26 Figure 10: PCB View of Expansion Modules
Page 32 - Figure 12: Expansion Modules Cabinet for North America
D N 1 7 2 6 - 0 8 11 28 Figure 12: Expansion Modules Cabinet for North America
Page 33 - Troubleshooting; Table 3: Reset Types and Descriptions; Forced Default Static:
D N 1 7 2 6 - 0 8 11 29 K T - 4 0 0 E t h e r n e t F o u r - D o o r C o n tr o l l e r I n s t a l l a t i o n M a n u a l Troubleshooting Table 3: Reset Types and Descriptions Jumpers Heartbeats Patterns Resets Continuous quick flashing Soft Reset: When JP2 and JP3 are ON, the controller will res...
Page 34 - Default initialization; The KT-400 default initialization or; is done at Kantech. The following steps should only be; Factory Default DHCP; Check the blue VITAL LED heartbeat pattern.
D N 1 7 2 6 - 0 8 11 30 Default initialization The KT-400 default initialization or Factory Default DHCP is done at Kantech. The following steps should only be followed if: a) You want to configure the KT-400 with the KT-Finder, see page 33. b) The KT-400 was communicating via the RS-232 port and yo...
Page 35 - ) Annual test for emergency lithium ion battery:
D N 1 7 2 6 - 0 8 11 31 K T - 4 0 0 E t h e r n e t F o u r - D o o r C o n tr o l l e r I n s t a l l a t i o n M a n u a l KT-400 Ethernet Four-Door Controller Maintenance Recommendations The KT-400 includes a lithium ion rechargable battery (see the KT-400 Ethernet Four-Door Controller PCB View o...
Page 36 - Optional Documentation; Networking Basics; Before you start; Forced Default Static; Network Configuration Information Sheet; Save configuration to KT-400
D N 1 7 2 6 - 0 8 11 32 Configuring the KT-400 Ethernet Four-Door Controller with the Web Configuration Page This procedure is practical if you want to configure the KT-400 in advance before going on site. Optional Documentation Application Note, Networking Basics , DN1796. Before you start • The de...
Page 37 - It doesn’t require any installation.; on the; from the; Device; of the KT-400 then click on; Connect
D N 1 7 2 6 - 0 8 11 33 K T - 4 0 0 E t h e r n e t F o u r - D o o r C o n tr o l l e r I n s t a l l a t i o n M a n u a l Configuring the KT-400 Ethernet Four-Door Controller with the KT-Finder The KT-Finder is an application used to configure the KT-400 over the local area network (LAN) or the w...
Page 39 - For more details, refer to the EntraPass Reference Manual.; DHCP; or; Static; EntraPass Special Edition / Corporate Gateway
D N 1 7 2 6 - 0 8 11 35 K T - 4 0 0 E t h e r n e t F o u r - D o o r C o n tr o l l e r I n s t a l l a t i o n M a n u a l KT-400 Ethernet Four-Door Controller Network Configuration Information Sheet Please complete one sheet per KT-400 Ethernet Four-Door Controller Company Name: Site Name: LAN or...
Page 40 - EntraPass Site; EntraPass Gateway Ports:; KT-400 Ethernet Four-Door Controller Site; Static or
D N 1 7 2 6 - 0 8 11 36 Configuration in a Wide Area Network (WAN) EntraPass Site For more details, refer to the EntraPass Reference Manual. EntraPass Special Edition / Corporate Gateway IP Address: ______.______.______.______ Router Public IP Address:______.______.______.______ or Domain name: ____...
Page 41 - Installation Checklist
D N 1 7 2 6 - 0 8 11 37 K T - 4 0 0 E t h e r n e t F o u r - D o o r C o n tr o l l e r I n s t a l l a t i o n M a n u a l Installation Checklist To the Installer: If you are familiar with the installation, you can use the checklist with the symbol. Installing the KT-400 Ethernet Four-Door Control...
Page 42 - Inputs and Outputs Assignments Sheet; Doors
D N 1 7 2 6 - 0 8 11 38 Inputs and Outputs Assignments Sheet Doors DOOR 1 CONTACT REX DOOR 2 CONTACT REX DOOR 3 CONTACT REX DOOR 4 CONTACT REX Inputs DOOR Z1 NO or NC EOL, DRY or DEOL REX Z2 NO or NC EOL, DRY or DEOL INPUT Z3 NO or NC EOL, DRY or DEOL INPUT Z4 NO or NC EOL, DRY or DEOL DOOR Z5 NO or...
