Alliance PHM802N- User Manual

Alliance PHM802N

Alliance PHM802N– User Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.

1 Page 1
2 Page 2
3 Page 3
4 Page 4
5 Page 5
6 Page 6
7 Page 7
8 Page 8
9 Page 9
10 Page 10
11 Page 11
12 Page 12
13 Page 13
14 Page 14
15 Page 15
16 Page 16
17 Page 17
18 Page 18
19 Page 19
20 Page 20
21 Page 21
22 Page 22
23 Page 23
24 Page 24
25 Page 25
26 Page 26
27 Page 27
28 Page 28
29 Page 29
30 Page 30
31 Page 31
32 Page 32
33 Page 33
34 Page 34
35 Page 35
36 Page 36
37 Page 37
38 Page 38
39 Page 39
40 Page 40
41 Page 41
42 Page 42
43 Page 43
44 Page 44
45 Page 45
46 Page 46
47 Page 47
48 Page 48
49 Page 49
50 Page 50
51 Page 51
52 Page 52
53 Page 53
54 Page 54
55 Page 55
56 Page 56
57 Page 57
58 Page 58
59 Page 59
60 Page 60
61 Page 61
62 Page 62
63 Page 63
64 Page 64
Page: / 64

Table of Contents:

  • Page 3 – Table of; Safety Information; Mounting Bolt Installation Requirements; Startup
  • Page 4 – Maintenance
  • Page 5 – Explanation of Safety Messages; DANGER
  • Page 6 – NOTE: The WARNINGS and IMPORTANT
  • Page 7 – IMPORTANT: Ensure that the recommended; Safety Decals; Safety decals appear at crucial locations on the; WARNING
  • Page 8 – Operator Safety
  • Page 9 – Introduction; Model Identification; Information in this manual is applicable to these
  • Page 10 – Delivery Inspection; Nameplate Location - UniLinc Models; Figure 1; Replacement Parts; MODEL EXAMPLE OF NAMEPLATE LOCATION
  • Page 11 – Specifications and Dimensions; UW Models; Wash Cylinder Information
  • Page 14 – Machine Dimensions; Dimensional Clearances; Allow a minimum of 610 mm (24 inches) at the rear; Figure 2; Dimension; Table 1
  • Page 16 – Figure 3
  • Page 17 – Machine Foundation Requirements; Table 2; Figure 4; Machine Mounting and Grouting; To reduce the risk of fire, serious injury,
  • Page 19 – Floor Load Data; Dynamic load
  • Page 20 – Maximum vertical
  • Page 21 – NOTE: If installing epoxy bolts into an elevated; Figure 5
  • Page 22 – Figure 6; To avoid personal injury and/or property
  • Page 23 – Grout Placement
  • Page 24 – NOTE: Mounting holes marked “A” need to be; Mounting Bolt Hole Locations; IMPORTANT: All drawings are not to scale.; Figure 7; FRONT OF MACHINE
  • Page 25 – Figure 8
  • Page 26 – Figure 9
  • Page 30 – Gap Setting for Vibration Switch; Figures; Only trained personnel should perform this
  • Page 31 – 5 Pound Models
  • Page 32 – VIBRATION SWITCH
  • Page 33 – Drain Connection Requirements; IMPORTANT: Machines must be installed in; Table 3; NOTE: Installation of additional machines will; Table 4; DIRECT DRAIN SYSTEM; DRAIN TROUGH SYSTEM
  • Page 34 – IMPORTANT: Do not block the machine overflow; Number of drain outlets
  • Page 35 – Water Connection; Table 6; To prevent personal injury, avoid contact; Water Supply Information; Table 5
  • Page 36 – Water Supply Line Sizing
  • Page 37 – Electrical Installation Requirements; N, P AND R – VOLTAGE MODELS
  • Page 38 – IMPORTANT: Do NOT use fuses in place of a; CAUTION; MACHINES WITH ELECTRIC HEAT; MACHINES WITHOUT ELECTRIC HEAT
  • Page 39 – NOT AVAILABLE
  • Page 41 – For machines equipped with optional steam heat,; NOTE: Failure to install the supplied steam filter; Steam Supply Information; Steam inlet connection,
  • Page 42 – Chemical Injection Supply System
  • Page 43 – Connecting External Liquid Supplies; Number of dry supply compartments
  • Page 45 – External Supplies
  • Page 47 – Remove the red jumper wire installed by the; Do not attempt to increase fuse rating or
  • Page 48 – External Supply Signals
  • Page 49 – Basket Rotation; After installation is complete, run the machine through
  • Page 50 – Operation; NOTE: Door must be opened within 5 seconds of
  • Page 51 – not; Be careful around the open door,; For Technical Ser vice; Supply Set; Towels
  • Page 52 – Shakeout Routine; Programming Manual
  • Page 54 – NOTE: The drain step that occurs before an; Cycle Number; Table 9; NEVER insert hands or objects into basket
  • Page 55 – steam heat
  • Page 56 – Monthly; Service Schedule Menu; Quarterly
  • Page 57 – Daily; Beginning of Day; Weekly
  • Page 58 – NOTE: Disconnect power to the machine at its
  • Page 59 – NOTE: Disconnect power to the machine before
  • Page 60 – Care of Stainless Steel
  • Page 61 – Disposal of Unit
Loading the manual

Installation/Operation/Maintenance

www.alliancelaundry.com

Washer-Extractors

Pocket Hardmount

Refer to Page 7 for Model Numbers

PHM1420C

PHM798N

PHM802N

PHM798N

PHM802N

PHM1420C

Part No. F8423301ENR1

November 2012

Original Instructions
Keep These Instructions for Future Reference.

(If this machine changes ownership, this manual must accompany machine.)

"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.

Other Manuals for Alliance PHM802N

Summary

Page 3 - Table of; Safety Information; Mounting Bolt Installation Requirements; Startup

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT © Copyright 2012, Alliance Laundry Systems LLCAll rights reserved. No part of the contents of this book may be reproduced or transmitted in any form or by any means without the expressed written consent of the publisher. F8423301 (E...

Page 4 - Maintenance

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 2 F8423301 (EN) Maintenance ........................................................................................ 54 Daily ..................................................................................................... 55 B...

Page 5 - Explanation of Safety Messages; DANGER

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 3 F8423301 (EN) Safety Information Explanation of Safety Messages Precautionary statements (“DANGER,” “WARNING,” and “CAUTION”), followed by specific instructions, are found in this manual and on machine decals. These precautions ar...

Other Alliance Models