ADTRAN NetVanta 1024 - Manual

Quick Start Guide, 61200506L1-13A, March 2006

Technical Support 1-888-4ADTRAN (1-888-423-8726)

Copyright © 2006 ADTRAN, All Rights Reserved

For more detailed documentation, visit us online at

www.adtran.com

.

Quick Start Guide

®

NetVanta 1024 PWR Power over Ethernet Midspan

P/N 1200506L1

DATA & POWER

DATA

NetVanta 1024

Power over Ethernet

P

OWER

OVER

E

THERNET

The NetVanta 1024 PWR Power over Ethernet Midspan products provide a cost effective way to
offer power over Gigabit Ethernet to existing nonpowered switches. These units deliver 15.4 watts
per port (up to 370 watts), supporting power over Ethernet. This supplies 48 VDC to powered
devices (e.g., IP phones, wireless access points, IP cameras, etc.) over existing CAT5 cabling.
These NetVanta products are fully compliant with IEEE 802.3af Power over Ethernet (PoE)
standards, and they support legacy (pre-standard) PoE.

By default, the midspan products detect and provide power to nonpowered switches.

G

ETTING

S

TARTED

Two configuration methods are available for your NetVanta unit:

•

Web-based GUI

•

AOS Command Line Interface (CLI)

The GUI lets you configure the main unit settings and provides online guidance and explanations for
each setting. However, using the AOS CLI may be necessary for more advanced configurations.

A

CCESS

THE

GUI

You can access the web-based GUI from any web browser on your network by following these
steps:

1.

Connect the unit to your PC using the

ETH 0/0

port on the rear of the unit.

2.

Set your PC to a fixed IP address of

10.10.10.2

. If you cannot change the PC’s IP address, you

will need to change the unit’s IP address using the CLI. (Refer to the next two sections for
instructions.)

3.

Enter the unit’s IP address in your browser address line. The default IP address is

10.10.10.1

.

4.

You will then be prompted for the username and password (the default settings are

admin

and

password

).

5.

The initial GUI screen appears.

A

CCESS

THE

CLI

Access the AOS CLI via the

CONSOLE

port or a Telnet session. To establish a connection to the

NetVanta unit

CONSOLE

port, you need the following items:

•

VT100 terminal or PC (with VT100 terminal emulation software)

•

Straight-through serial cable with a DB-9 (male) connector on one end and the appropriate
interface for your terminal or PC communication port on the other end

1.

Connect the DB-9 (male) connector of your serial cable to the

CONSOLE

port on the rear

panel of the unit.

2.

Connect the other end of the serial cable to the terminal or PC.

3.

Insert the connector of the provided power cord into the power interface on the rear panel of
the unit, and plug the cord into a standard electrical outlet.

4.

Once the unit is powered up, open a VT100 terminal session using the following settings:
9600 baud, 8 data bits, no parity bits, and 1 stop bit. Press

<Enter>

to activate the AOS CLI.

5.

Enter

enable

at the

>

prompt.

6.

Enter the enable password when prompted. The default password is

password

.

C

ONFIGURE

THE

U

NIT

’

S

IP A

DDRESS

The following steps create an IP address and subnet mask for the

ETH 0/0

port. If you are not sure

what IP address to assign, please contact your network administrator.

1.

At the

#

prompt, enter

config terminal

.

2.

At the

(config)#

prompt, enter

interface eth 0/0

to access the configuration parameters for

the Ethernet interface.

3.

Enter

ip address 10.26.12.12 255.255.255.0

to assign an IP address to the Ethernet

interface using a 24-bit subnet mask.

4.

Enter

no shutdown

to activate the interface to pass data.

5.

Enter

exit

to return to the Global Configuration mode.

Depending on your configuration, you may need to set a default gateway
as well using the

(config)#ip default gateway

command. If IP routing is

enabled on the unit, do NOT set a default gateway.