ADTRAN 3430 - Manual

Quick Start Guide, 61200820E1-13A, July 2006

Technical Support 1-888-4ADTRAN (1-888-423-8726)

Copyright © 2006 ADTRAN, All Rights Reserved

For more detailed documentation, visit us online at

www.adtran.com

.

Quick Start Guide

®

NetVanta 3430 Router

P/N 1200820E1

G

ETTING

S

TARTED

Two configuration methods are available for your NetVanta router:

•

Web-based GUI

•

AOS Command Line Interface (CLI)

The GUI lets you configure the main unit settings and provides online guidance and explanations
for each setting. However, using the AOS CLI may be necessary for more advanced
configurations.

A

CCESS

THE

GUI

You may access the web-based GUI from any web browser on your network by following these
steps:

1.

Connect the router to your PC using the

ETH 0/1

port on the back of the unit.

2.

Set your PC to a fixed IP address of 10.10.10.2. If you cannot change the PC’s IP address,
you will need to change the unit’s IP address using the CLI. (Refer to the next two sections for
instructions.)

3.

Enter the unit’s IP address in your browser address line. The default IP address is 10.10.10.1.

4.

You will then be prompted for the username and password (the default settings are

admin

and

password

).

5.

The initial GUI screen appears.

A

CCESS

THE

CLI

Access the AOS CLI via the

CONSOLE

port or a Telnet session. To establish a connection to the

NetVanta router

CONSOLE

port, you need the following items:

•

VT100 terminal or PC (with VT100 terminal emulation software)

•

Straight-through serial cable with a DB-9 (male) connector on one end and the appropriate
interface for your terminal or PC communication port on the other end

1.

Connect the DB-9 (male) connector of your serial cable to the

CONSOLE

port on the rear

panel of the unit.

2.

Connect the other end of the serial cable to the terminal or PC.

3.

Provide power to the unit as appropriate. See the

NetVanta 3000 Series Hardware Installation

Guide

(provided on the

ADTRAN OS System Documentation

CD) for more details.

4.

Once the unit is powered up, open a VT100 terminal session using the following settings:
9600 baud, 8 data bits, no parity bits, and 1 stop bit. Press

<Enter>

to activate the

AOS CLI.

5.

Enter

enable

at the

>

prompt.

6.

Enter the enable password when prompted. The default password is

password

.

C

ONFIGURE

THE

U

NIT

’

S

IP A

DDRESS

The following steps create an IP address and subnet mask for

ETH 0/1

. If you are not sure what IP

address to assign, please contact your network administrator.

1.

At the

#

prompt, enter

config terminal

.

2.

At the

(config)#

prompt, enter

interface eth 0/1

to access the configuration parameters for

the Ethernet port located on the rear of the unit.

3.

Enter

ip address 10.26.12.12 255.255.255.0

to assign an IP address to the Ethernet port

using a 24-bit subnet mask.

4.

Enter

ip route 0.0.0.0 0.0.0.0 192.22.72.2

to add a default route to the route table. If

necessary, contact your network administrator to obtain the IP address (and subnet mask) for
your particular configuration.

5.

Enter

no shutdown

to activate the interface to pass data.

6.

Enter

exit

to exit the Ethernet interface commands and return to the Global Configuration

mode.

The configuration parameters used in the examples outlined in this
document are for instructional purposes only. Please replace all
underlined entries (

example

) with your specific parameters to configure

your application.

Depending on your configuration, you may need to set a default gateway
as well using the

(config)#ip default gateway

command. If IP routing is

enabled on the unit, do NOT set a default gateway.