ADTRAN 340 - Manual
ADTRAN 340 – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
INSTALLING THE NETVANTA 340 ROUTER
P/N 1200422L1
For more detailed documentation, visit us online at
Quick Start Guide
Quick Start Guide, 61200422L1-13C, December 2004
Technical Support 1-888-4ADTRAN (1-888-423-8726)
Copyright
©
2004 ADTRAN, All Rights Reserved
•
If pressed during boot up, the default switch (pointed out in the illustration
above) will cause the unit to stay in bootstrap mode. Since the unit has no
serial port, Telnet has been built in to the boot code. The default IP address
is 10.10.10.1.
•
If pressed and held for 5 seconds after boot, the
E
THERNET
interface will
default to 10.10.10.1, and all access policies will be removed from that
interface.
•
If pressed for 30 seconds, a default configuration will overwrite your
existing configuration and reboot the unit.
F
ACTORY
D
EFAULT
S
WITCH
C
ONNECT
TO
THE
N
ET
V
ANTA
340
1. Connect the NetVanta 340
E
THERNET
interface to the PC using the appropriate
Ethernet cable.
2. Supply power to the PC and the NetVanta 340 and begin the operating system boot
up process. During boot up, the PC obtains an IP address from the NetVanta 340
DHCP server. By default, both the DHCP and HTTP Servers are enabled. The
default IP address is 10.10.10.1.
3. Open your internet browser and enter 10.10.10.1. in the URL field. The NetVanta 340
login window appears.
4. Enter the default username (
admin
) and password (
password
), and click the
OK
button.
C
ONFIGURE
THE
ATM PVC
1. Click on the
Getting Started
link under the
System
menu.
This willl bring up a side bar page.
2. Click on
Step 1 - Configure the Public Interface
at the top of
the side bar page to open the ATM PVC page.
3. Fill in the PVC number and select an
Interface Mode
. This is
usually PPP or PPPoE; however, if
IP routing
is chosen, you
will need to enter an IP address.
4. Click
Apply
. If PPP or PPPoE
is selected as the
Interface
Mode
, you will be taken to the PPP page after clicking
Apply
.
Here you will need to select the type of authentication needed,
authentication passwords, and the
Address Type
. In most
cases you will want the
Address Type
to be
Negotiated
. Click
Apply
when all the information is complete.
•
One integrated 10/100 Ethernet port
•
ADSL Network Interface - ITU 992.1, 992.2, ANSI T1.413 Issue 2
•
WAN Protocol: ATM
•
Integrated IP Router with Bridging
•
Command Line Interface (CLI)
•
SNMP Management
•
Web Based Management
•
Front panel LEDs
•
Dying gasp capability
•
Dynamic rate adaption support
F
EATURES
5. By default, the NetVanta 340 comes with an ADSL and an ATM (Asynchronous
Transfer Mode) port already configured and enabled. The service provider should
provide a PVC (VPI / VCI) number which will be used to configure the ATM PVC.
For security purposes, you should set up an
admin
password immediately.
Use the
Passwords
page of the Web GUI to change this password.
The default switch must be pressed WHILE the power light is
blinking green. Do not press the default switch BEFORE the
power light is blinking green, as this will cause boot to be missed.
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
