ADTRAN 2FXS/DPO PM - Manual
ADTRAN 2FXS/DPO PM – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
1
Section 61109.403L2-5, Issue 3
61109.403L2-5C
1.
GENERAL
This practice provides installation and maintenance
information for the ADTRAN
®
Intelligent 2-Wire Foreign
Exchange Station/Dial Pulse Originate (2FXS/DPO PM)
Dataport with Performance Monitoring, part number
1109403L2. It is a D4 compatible channel unit and
operates in any standard D4 channel bank. Intelligent
features requires the unit to be used in the ADTRAN ACT
2300, ACT 1900 , or standard WECO
®
D4 channel bank
using the ADTRAN LIU-3/PM common unit. The 2FXS/
DPO PM provides an interface between a D4 channel
bank Pulse Code Modulation (PCM) backplane interface
and a 2-wire voice frequency (VF) transmission and
signaling facility. Figure 1 is an illustration of the 2FXS/
DPO PM. The unit is multifunctional and can be
provisioned to operate in the following modes:
• 2-Wire Foreign Exchange Station (2FXS)
• Dial Pulse Originate (DPO)
• Tandem FXS Mode
• Private Line Auto Ringdown (PLAR)
Section 61109403L2-5
Issue 3, November 1997
CLEI Code: D4F1DFJ_ _ _
2FXS/DPO PM
FOREIGN EXCHANGE STATION/DIAL PULSE ORIGINATE DATAPORT
WITH PERFORMANCE MONITORING
INSTALLATION AND MAINTENANCE
PRACTICES
Figure 1. 2FXS/DPO
C A U T I O N !
SUBJECT TO ELECTROSTATIC DAMAGE
OR DECREASE IN RELIABILITY.
HANDLING PRECAUTIONS REQUIRED.
Using the FXS/DPO PM in an intelligent channel bank
provides additional features and functions such as:
• Local and Remote Provisioning using either the craft
interface or ADTRAN Site Manager through a menu
driven program called EASYMENU™
• Performance monitoring of the loop
• Network and customer side monitoring and analysis
• Enhanced Test Capabilities
Revision History
Revisions to this practice include CLEI code and dip
switch settings.
Features
• Backplane interface to the Pulse Code Modulation
(PCM) bus.
• On board coder/decoder (CODEC) uses
µ
-law
encoding/decoding.
• Nominal 600 ohm or 900 ohm 2-Wire VF interface with
DC isolation.
Trademarks: Any brand names and product names included in this document are trademarks, registered trademarks, or trade names
of their respective holders.
2FXS/DPO
1109403L2
PM
AP
REM
PM
TEST
BUSY
SW 4
SW 3
SW 2
SW 1
SW 7
CONTENTS
GENERAL ................................................................... 1
INSTALLATION ........................................................... 2
CONNECTIONS .......................................................... 4
TESTING ..................................................................... 4
MAINTENANCE .......................................................... 5
WARRANTY AND CUSTOMER SERVICE ................ 5
FIGURES
Figure 1. 2FXS/DPO ........................................................... 1
Figure 2. Circuit Path .......................................................... 3
Figure 3. Connector ............................................................ 4
TABLES
Table A. SW1 (Receive) and SW2 (Transmit) ................... 2
Table B. SW3, SW4, and SW5 Option Settings ................ 2
Table C. Manual Configuration Guide ................................ 3
Table D. Electronic Provisioning Settings .......................... 3
Table E. 2FXS/DPO Faceplate Indicators ......................... 4
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
