ADTRAN 1200130L1 - Manual - manualsarea.com

Page 2 - 01 Explorer Boulevard

This product includes software developed by the University of California, Berkeley,and its contributors. 901 Explorer Boulevard P.O. Box 140000 Huntsville, AL 35814-4000 Phone: (205) 963-8000 © 1997 ADTRAN, Inc. All rights reserved. Printed in USA.

Page 3 - ABOUT THIS MANUAL

ABOUT THIS MANUAL This manual is arranged so you can quickly and easily find theinformation you need. The following is an overview of thecontents of this manual: • Chapter 1, Introduction, familiarizes you with frame relay networks and FSU highlights and gives a brief explanation ofoptions that may ...

Page 4 - Notes provide additional useful information.

Notes provide additional useful information. Cautions signify information that could prevent service interruption. Warnings provide information that could prevent damage to theequipment or endangerment to human life.

Page 6 - CANADIAN EMISSIONS REQUIREMENTS

FEDERAL COMMUNICATIONS COMMISSION RADIO FREQUENCY INTERFERENCE STATEMENT: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant toPart 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interferencewhen ...

Page 9 - Table of Contents

6 1 2 0 0 . 1 3 0 L 1 - 1 F S U U s e r M a n u a l i Table of Contents Chapter 1. IntroductionUnderstanding Frame Relay ................................................................................................. 1Product Overview ..................................................................

Page 10 - Chapter 4. Applications

Table of Contents i i F S U U s e r M a n u a l 6 1 2 0 0 . 1 3 0 L 1 - 1 View Statistics (STATS) ................................................................................... 19Diagnostics (DIAG) ......................................................................................... 19Save ...

Page 15 - Chapter 1; UNDERSTANDING FRAME RELAY

6 1 2 0 0 . 1 3 0 L 1 - 1 F S U U s e r M a n u a l 1 Chapter 1. Introduction Chapter 1 Introduction UNDERSTANDING FRAME RELAY Frame relay is a wide area network (WAN) service designed tominimize physical connections. This is accomplished by usingvirtual connections within the frame relay cloud and ...

Page 16 - PRODUCT OVERVIEW; The major features of the FSU are as follows:

2 F S U U s e r M a n u a l 6 1 2 0 0 . 1 3 0 L 1 - 1 Chapter 1. Introduction equipment. This DLCI is valid until the call is disconnected andmay be assigned a different value each time a call is requested. PRODUCT OVERVIEW The FSU provides a low cost solution for the CPE equipment in aprivate or pu...

Page 17 - DDS OPERATION

6 1 2 0 0 . 1 3 0 L 1 - 1 F S U U s e r M a n u a l 3 Chapter 1. Introduction relay DTE MIB), RFC 1213 (MIB II), and ADTRAN EnterpriseMIB. • DCE port supporting rates of up to 512 kbps.• Optional integrated 56/64 DDS DSU/CSU.• Telnet-provided remote terminal management control.• FLASH code space for...

Page 18 - WARRANTY AND CUSTOMER SERVICE

4 F S U U s e r M a n u a l 6 1 2 0 0 . 1 3 0 L 1 - 1 Chapter 1. Introduction WARRANTY AND CUSTOMER SERVICE ADTRAN will replace or repair this product within five yearsfrom the date of shipment if it does not meet its publishedspecifications or fails while in service. For detailed warranty,repair, a...

Page 19 - Chapter 2; Receiving Inspection; integrated DSU option is installed (part number 1200130L2)

6 1 2 0 0 . 1 3 0 L 1 - 1 F S U U s e r M a n u a l 5 Chapter 2. Installation Chapter 2 Installation UNPACK, INSPECT, POWER UP Receiving Inspection Carefully inspect the FSU for any damage that may have oc-curred in shipment. If damage is suspected, file a claim immedi-ately with the carrier and con...

Page 20 - Power Up

6 F S U U s e r M a n u a l 6 1 2 0 0 . 1 3 0 L 1 - 1 Chapter 2. Installation Power Up Each FSU unit is provided with a captive eight-foot power cord,terminated by a three-prong plug which connects to a grounded115 VAC power receptacle. Power to the FSU must be provided from a grounded 115 VAC, 60 H...

Page 21 - Item; FSU Rear View

6 1 2 0 0 . 1 3 0 L 1 - 1 F S U U s e r M a n u a l 7 Chapter 2. Installation CONTROL MAIN BACKUP TELCO DCE ON OFF 115VAC 60Hz DTE 2 DTE 1 DSU/CSU ENTER 1 2 3 4 5 6 7 8 9 # 0 * CANCEL SHIFT QUICK D A E B F C R S C S T D R D C D A L M T S T DSU III AR Frame Relay VT 100 Terminal DTE Device DTE Device...

Page 22 - DCE Connector

8 F S U U s e r M a n u a l 6 1 2 0 0 . 1 3 0 L 1 - 1 Chapter 2. Installation DCE Connector The connector labeled DCE provides connection to an externalDSU/CSU. The pinouts for this connector are shown in theappendix Pinouts. The connection between the FSU and an external DSU is a directconnection. ...

Page 23 - Control Port

6 1 2 0 0 . 1 3 0 L 1 - 1 F S U U s e r M a n u a l 9 Chapter 2. Installation Control Port The eight-position modular jack labeled CONTROL providesconnection to a VT 100 RS-232 compatible interface. This enablesthe FSU to be configured through a terminal instead of the frontpanel. Use the VT 100 ter...

Page 25 - Chapter 3; FRONT PANEL; Displays menu items and messages in 2 lines by 16 characters.; to select the active menu item.

6 1 2 0 0 . 1 3 0 L 1 - 1 F S U U s e r M a n u a l 1 1 Chapter 3. Operation Chapter 3 Operation FRONT PANEL The FSU faceplate is shown in Figure 3-1. Descriptions of eachpart of the front panel follow. LCD Window Displays menu items and messages in 2 lines by 16 characters. Enter Selects active men...

Page 26 - Up

1 2 F S U U s e r M a n u a l 6 1 2 0 0 . 1 3 0 L 1 - 1 Chapter 3. Operation To activate a menu item designated by an alpha character ratherthan a number, place the cursor on the menu item using the Upand Down Arrows or press Shift and then the letter. Theflashing cursor indicates which parameter is...

Page 27 - FSU Front Panel

6 1 2 0 0 . 1 3 0 L 1 - 1 F S U U s e r M a n u a l 1 3 Chapter 3. Operation Figure 3-1 FSU Front Panel SHIFT CANCEL ENTER * 7 D 4 A 1 8 0 E 5 B 2 QUICK FSU # 9 F 6 C 3 TD1 RD1 TD2 RD2 TDN RDN ALM TST DEL NEXT PREV ADD Numeric Keypad Activates menu items and enters numeric information. TD2 LED Activ...

Page 30 - Front Panel Operation; to select the item. The following steps and Figure 3-2

1 6 F S U U s e r M a n u a l 6 1 2 0 0 . 1 3 0 L 1 - 1 Chapter 3. Operation Front Panel Operation To choose a menu item, press the corresponding number oralpha character on the keypad. Press Shift to activate menuitems with alpha selections. Scrolling to the selection by press-ing either the Up or ...

Page 31 - VT 100 Terminal Connection and Operation

6 1 2 0 0 . 1 3 0 L 1 - 1 F S U U s e r M a n u a l 1 7 Chapter 3. Operation VT 100 Terminal Connection and Operation To control the FSU using a VT 100 terminal, perform the follow-ing procedure: 1. Set the FSU baud rate to match the terminal through the front panel. Select 1 CONFIG, then 4 CONTROL ...

Page 32 - Terminal Login Menu

1 8 F S U U s e r M a n u a l 6 1 2 0 0 . 1 3 0 L 1 - 1 Chapter 3. Operation Figure 3-3 Terminal Login Menu Figure 3-4 Terminal Main Menu

Page 33 - FSU MENU STRUCTURE; The Logout selection is available on the VT 100 interface only.; Main Menu; Definitions for the branches of the Main menu follow:

6 1 2 0 0 . 1 3 0 L 1 - 1 F S U U s e r M a n u a l 1 9 Chapter 3. Operation FSU MENU STRUCTURE The opening menu is the access point to all other operations.The Main menu branches are Configuration, Statistics, Diagnos-tics, Save, Abort, and Logout. See Figure 3-2. Each Main menuitem has several fun...

Page 34 - This parameter saves the currently selected configuration.

2 0 F S U U s e r M a n u a l 6 1 2 0 0 . 1 3 0 L 1 - 1 Chapter 3. Operation Save Configuration (SAVE) This parameter saves the currently selected configuration. Configuration changes are not implemented until the Save Configura-tion (SAVE) option is selected. Abort Changes (ABORT) This parameter ca...

Page 35 - Chapter 4; SNA/SDLC with Local Spoofing

6 1 2 0 0 . 1 3 0 L 1 - 1 F S U U s e r M a n u a l 2 1 Chapter 4. Applications Chapter 4 Applications This chapter provides examples of some common FSU applica-tions. The examples include SNA/SDLC with local spoofing,SNMP/Telnet management, bisync point-to-point and multi-point, and transparent app...

Page 36 - SNA /SDLC with Local Spoofing

2 2 F S U U s e r M a n u a l 6 1 2 0 0 . 1 3 0 L 1 - 1 Chapter 4. Applications In all cases, the FSU is transparent to the XID (exchange identifica-tion) negotiation between any two network devices. The FSU uses LLC protocol (mode 2) to transport SDLC informa-tion frames. This protocol ensures a re...

Page 37 - Configuration Settings for SNA/SDLC Application

6 1 2 0 0 . 1 3 0 L 1 - 1 F S U U s e r M a n u a l 2 3 Chapter 4. Applications Table 4-A Configuration Settings for SNA/SDLC Application HOST FSU REMOTE FSU DTE Port 1 P r o t o c o l SDLC SDLC Physical Layer CONN=RS232 CONN=RS232 O p t i o n s RATE=19.2K RATE=19.2K IDLE=ONES IDLE=ONES Protocol FOR...

Page 38 - SNA and LAN Application with SNMP/Telnet Management; RIP and inverse ARP are not used for the FSU DTE frame relay port.

2 4 F S U U s e r M a n u a l 6 1 2 0 0 . 1 3 0 L 1 - 1 Chapter 4. Applications SNA and LAN Application with SNMP/Telnet Management When used in a mixed environment consisting of both SNA andLAN networks, the FSU serves as a concentrator, allowing bothnetworks access to one frame relay link. The exa...

Page 40 - Configuration Settings for SNA and LAN Application

2 6 F S U U s e r M a n u a l 6 1 2 0 0 . 1 3 0 L 1 - 1 Chapter 4. Applications Table 4-B Configuration Settings for SNA and LAN Application HOST FSU REMOTE FSU DTE Port 1 P r o t o c o l SDLC SDLC P h y s i c a l CONN=RS232 CONN=RS232 O p t i o n s RATE=19.2K RATE=19.2K IDLE=ONES IDLE=ONES Protocol...

Page 41 - Bisync Application

6 1 2 0 0 . 1 3 0 L 1 - 1 F S U U s e r M a n u a l 2 7 Chapter 4. Applications Bisync Application The FSU can be used to connect IBM 3780/2780 (see IBM manualnumber GA27-3004-2) bisync controllers and a host across aframe relay network. Point-to-point and multi-point configura-tions are supported a...

Page 43 - Configuration Settings for Multi-Point Bisync Application

6 1 2 0 0 . 1 3 0 L 1 - 1 F S U U s e r M a n u a l 2 9 Chapter 4. Applications Table 4-C Configuration Settings for Multi-Point Bisync Application HOST FSU REMOTE FSU DTE Port 1 P r o t o c o l BISYNC BISYNC P h y s i c a l CONN=RS232 CONN=RS232 O p t i o n s RATE=9600 RATE=9600 Protocol LINE=MULTI...

Page 44 - Transparent Application; Transparent BOP Application

3 0 F S U U s e r M a n u a l 6 1 2 0 0 . 1 3 0 L 1 - 1 Chapter 4. Applications Transparent Application In cases when the user protocol is not supported by the FSU, thetransparent mode may be used. Transparent bit-orientedprotocol (BOP) or transparent asynchronous protocol may beselected. This can b...

Page 45 - Configuration Settings for Transparent BOP Application; Transparent Async Application

6 1 2 0 0 . 1 3 0 L 1 - 1 F S U U s e r M a n u a l 3 1 Chapter 4. Applications Table 4-D Configuration Settings for Transparent BOP Application HOST FSU REMOTE FSU DTE Port 1 P r o t o c o l TRANS BOP TRANS BOP Physical Layer CONN=V.35 CONN=V.35 O p t i o n s RATE=64K RATE=64K IDLE=FLAGS IDLE=FLAGS...

Page 46 - Configuration Settings for Transparent Async Application

3 2 F S U U s e r M a n u a l 6 1 2 0 0 . 1 3 0 L 1 - 1 Chapter 4. Applications Table 4-E Configuration Settings for Transparent Async Application HOST FSU REMOTE FSU DTE Port 1 P r o t o c o l TRANS ASYNC TRANS ASYNC Physical Layer CONN=RS232 CONN=RS232 O p t i o n s BAUD=38.4K BAUD=38.4K DATA BITS...

Page 47 - Chapter 5; LOCAL AND REMOTE CONFIGURATION

6 1 2 0 0 . 1 3 0 L 1 - 1 F S U U s e r M a n u a l 3 3 Chapter 5. Configuration Overview Chapter 5 Configuration Overview LOCAL AND REMOTE CONFIGURATION The FSU can be configured locally or, when using the VT 100interface, communications can be established so a local FSU canconfigure a remote FSU. ...

Page 48 - VT 100 Configuration Menu

3 4 F S U U s e r M a n u a l 6 1 2 0 0 . 1 3 0 L 1 - 1 Chapter 5. Configuration Overview The FSU contains a default set of configuration options stored inread-only memory (see the appendix Default ConfigurationProfile). The unit is shipped from the factory with this profileloaded into the current (...

Page 49 - Front Panel Configuration Menu Tree

6 1 2 0 0 . 1 3 0 L 1 - 1 F S U U s e r M a n u a l 3 5 Chapter 5. Configuration Over view Figure 5-2 Front Panel Configuration Menu Tree DISABLEDFRAME RELAYS D L C 1 PROTOCOL TRANS BOPBISYNC 1 DTE PORT 1 TRANS ASYNC 2 PHYS LYR OPT PPP SYNC 2 DTE PORT 2 3 PROTOCOL OPT These selections are dependent ...

Page 51 - VT 100 Configuration Menu Tree

6 1 2 0 0 . 1 3 0 L 1 - 1 F S U U s e r M a n u a l 3 7 Chapter 5. Configuration Over view Figure 5-3 VT 100 Configuration Menu Tree 1 PORT DISABLED2 FRAME RELAY3 SDLC4 TRANSPARENT BOP 1 PROTOCOL 5 BISYNC 6 TRANSPARENT ASYNC 1 DTE PORT 1 7 PPP SYNCHRONOUS 2 PHYSICAL LAYER OPTIONS 8 PPP ASYNC9 SLIP 2...

Page 53 - Chapter 6; VT 100 Port Configuration Menu

6 1 2 0 0 . 1 3 0 L 1 - 1 F S U U s e r M a n u a l 3 9 Chapter 6. DTE Port Configuration Chapter 6 DTE Port Configuration Configure the protocol, physical layer options, protocol options,and protocol address table for the two DTE ports located on therear of the FSU by selecting DTE PORT 1 or DTE PO...

Page 54 - Front Panel Protocol Menu Tree

4 0 F S U U s e r M a n u a l 6 1 2 0 0 . 1 3 0 L 1 - 1 Chapter 6. DTE Port Configuration When configuring the DTE ports, select the protocol first. Thisselection determines which parameters will be available in theother three categories (Physical Layer Options, Protocol Options,and Protocol Address...

Page 55 - Port Disabled Menu Tree; Protocol options are not available when the port is disabled.

6 1 2 0 0 . 1 3 0 L 1 - 1 F S U U s e r M a n u a l 4 1 Chapter 6. DTE Port Configuration Port Disabled Protocol (DISABLED) Follow the menu tree shown in Figure 6-3 to disable the DTEport protocol. If only one of the DTE ports is in use, select PORTDISABLED for the unused port. 1 PROTOCOL 1 PORT DIS...

Page 56 - Frame Relay Protocol

4 2 F S U U s e r M a n u a l 6 1 2 0 0 . 1 3 0 L 1 - 1 Chapter 6. DTE Port Configuration Frame Relay Protocol The frame relay protocol is a synchronous protocol used toconcentrate two different devices into a common frame relay linkto the network. While configured for frame relay protocol, theFSU a...

Page 57 - Frame Relay Protocol Menu Tree

6 1 2 0 0 . 1 3 0 L 1 - 1 F S U U s e r M a n u a l 4 3 Chapter 6. DTE Port Configuration 1 PROTOCOL 2 FRAME RELAY 1 DTE PORT 1 2 PHYSICAL LAYER OPTIONS 1 INTERFACE TYPE 1 RS2322 V.35 1 CONFIG 1 2400 bps 2 DTE PORT 2 2 4800 bps3 9600 bps4 19.2 Kbps5 38.4 Kbps6 56 Kbps 2 SYNCHRONOUS BIT RATE 7 64 Kbp...

Page 59 - Edit the next entry in the address table.

6 1 2 0 0 . 1 3 0 L 1 - 1 F S U U s e r M a n u a l 4 5 Chapter 6. DTE Port Configuration Setting the IP address to 0.0.0.0 and setting the Mng DLCI to avalue not used by the attached frame relay device disables thisfeature. IP Address (IP ADDR) Enter the FSU IP address. Each port capable of carryin...

Page 60 - Edit the previous entry in the address table.; Delete the current entry in the address table.; SDLC Protocol

4 6 F S U U s e r M a n u a l 6 1 2 0 0 . 1 3 0 L 1 - 1 Chapter 6. DTE Port Configuration Edit Previous Entry (PREV key on front panel) Edit the previous entry in the address table. Delete This Entry (DEL key on front panel) Delete the current entry in the address table. Add New Entry (ADD key on fr...

Page 62 - SDLC Protocol Menu Tree

4 8 F S U U s e r M a n u a l 6 1 2 0 0 . 1 3 0 L 1 - 1 Chapter 6. DTE Port Configuration 1 PROTOCOL 3 SDLC 1 DTE PORT 1 1 INTERFACE TYPE 1 RS2322 V.35 1 CONFIG 2 PHYSICAL LAYER OPTIONS 1 2400 bps 2 DTE PORT 2 2 4800 bps3 9600 bps4 19.2 Kbps5 38.4 Kbps6 56 Kbps 2 SYNCHRONOUS BIT RATE 7 64 Kbps8 112 ...

Page 63 - Set the minimum time between transmission frames.

6 1 2 0 0 . 1 3 0 L 1 - 1 F S U U s e r M a n u a l 4 9 Chapter 6. DTE Port Configuration Poll/Response Timeout (TIMEOUT) Set the amount of time the FSU waits for a poll response beforeissuing another poll. Minimum Poll Timer This parameter defines the minimum time (ms) between con-secutive polls to...

Page 65 - Transparent BOP Menu Tree

6 1 2 0 0 . 1 3 0 L 1 - 1 F S U U s e r M a n u a l 5 1 Chapter 6. DTE Port Configuration Transparent BOP (TRANS BOP) Transparent BOP is a synchronous mode which can accept anyHDLC-like protocol as input. This setting allows the FSU toconnect to devices even if the FSU does not understand theirproto...

Page 67 - Bisync Protocol; Bisync Protocol Menu Tree

6 1 2 0 0 . 1 3 0 L 1 - 1 F S U U s e r M a n u a l 5 3 Chapter 6. DTE Port Configuration Bisync Protocol The Bisync protocol option enables the FSU to connect IBM2780/3780 bisync controllers to the host across frame relay. Bothpoint-to-point and multi-point configurations are supported. The FSU can...

Page 68 - Enable the FSU to transmit flags or all ones.

5 4 F S U U s e r M a n u a l 6 1 2 0 0 . 1 3 0 L 1 - 1 Chapter 6. DTE Port Configuration Physical Layer Options Interface Type (CONN) Select the connector type for the DTE interface. The choices areV.35 and RS-232. Synchronous Bit Rate (RATE) Select the operating speed of the DTE interface. These s...

Page 71 - Transparent Async Protocol Menu Tree

6 1 2 0 0 . 1 3 0 L 1 - 1 F S U U s e r M a n u a l 5 7 Chapter 6. DTE Port Configuration Transparent Async Protocol (TRANS ASYNC) Transparent Async protocol frames up async characters totransport across a frame relay network. This protocol is usedwhen the device connected to the FSU is an async dev...

Page 74 - PPP Synchronous Protocol Menu Tree

6 0 F S U U s e r M a n u a l 6 1 2 0 0 . 1 3 0 L 1 - 1 Chapter 6. DTE Port Configuration 1 PROTOCOL 7 PPP SYNCHRONOUS 1 DTE PORT 1 2 PHYSICAL LAYER OPTIONS 1 INTERFACE TYPE 1 RS2322 V.35 1 2400 bps 2 DTE PORT 2 2 4800 bps3 9600 bps 2 SYNCHRONOUS BIT RATE 4 19.2 Kbps 5 38.4 Kbps6 56 Kbps7 64 Kbps8 1...

Page 75 - Enter the IP address of the attached PPP device.

6 1 2 0 0 . 1 3 0 L 1 - 1 F S U U s e r M a n u a l 6 1 Chapter 6. DTE Port Configuration Synchronous Bit Rate (RATE) Select the operating speed of the DTE interface. The selectionsare 2400, 4800, and 9600 bps and 19.2, 38.4, 56, 64, 112, 128, 168,192, 224, 256, 280, 320, 384, 448, and 512 kbps. Spe...

Page 76 - PPP Async Protocol

6 2 F S U U s e r M a n u a l 6 1 2 0 0 . 1 3 0 L 1 - 1 Chapter 6. DTE Port Configuration PPP Async Protocol The PPP Async Protocol functions the same as the PPP Synchro-nous Protocol except for the port is in async format, connected toan async device. Special control characters are used to deter-mi...

Page 77 - PPP Asynchronous Protocol Menu Tree

6 1 2 0 0 . 1 3 0 L 1 - 1 F S U U s e r M a n u a l 6 3 Chapter 6. DTE Port Configuration Hardware Flow Control (HDW FLOW CTRL) When enabled, the FSU uses CTS to temporarily disable transmitdata to the FSU. 1 PROTOCOL 8 PPP ASYNC 1 DTE PORT 1 2 PHYSICAL LAYER OPTIONS 1 INTERFACE TYPE 1 RS2322 V.35 1...

Page 78 - Enter the internet protocol (IP) address of the FSU DTE port.

6 4 F S U U s e r M a n u a l 6 1 2 0 0 . 1 3 0 L 1 - 1 Chapter 6. DTE Port Configuration Protocol Address Table IP Address (IP ADDR) Enter the internet protocol (IP) address of the FSU DTE port. Subnet Mask Enter the subnet number of the network formed by the FSU andthe Peer PPP station. Peer IP Ad...

Page 79 - Slip Protocol

6 1 2 0 0 . 1 3 0 L 1 - 1 F S U U s e r M a n u a l 6 5 Chapter 6. DTE Port Configuration Slip Protocol The Slip Protocol is an asynchronous protocol which encapsu-lates and routes IP traffic to and from a SLIP device. Specialcontrol characters are used to define frame boundaries. SeeFigure 6-11 for...

Page 80 - Slip Protocol Menu Tree

6 6 F S U U s e r M a n u a l 6 1 2 0 0 . 1 3 0 L 1 - 1 Chapter 6. DTE Port Configuration Hardware Flow Control (HDW FLOW CTRL) When enabled, the FSU uses CTS to temporarily disable transmitdata to the FSU. 1 PROTOCOL 9 SLIP 1 DTE PORT 1 2 PHYSICAL LAYER OPTIONS 1 INTERFACE TYPE 1 RS232 2 V.35 1 CON...

Page 81 - Enter the IP address of the attached SLIP device.

6 1 2 0 0 . 1 3 0 L 1 - 1 F S U U s e r M a n u a l 6 7 Chapter 6. DTE Port Configuration Protocol Address Table IP Address (IP ADDR) Enter the internet protocol (IP) address of the FSU DTE port. Subnet Mask Enter the subnet number of the network formed by the FSU andthe Peer SLIP station. Peer IP A...

Page 83 - Chapter 7; NETWORK PORT

6 1 2 0 0 . 1 3 0 L 1 - 1 F S U U s e r M a n u a l 6 9 Chapter 7. Configuring the Network Port Chapter 7 Configuring the Network Port NETWORK PORT Access the Network Port menus by selecting Network Port fromthe Configuration menu. See the menu tree in Figure 7-1. Thenetwork port is always used in f...

Page 84 - Network Port Configuration Menu Tree

7 0 F S U U s e r M a n u a l 6 1 2 0 0 . 1 3 0 L 1 - 1 Chapter 7. Configuring the Network Port When connecting to an external DSU, the FSU emulates an externallytimed DTE interface connected directly to the DCE interface of theexternal device. Therefore, the connection between the FSU and theDSU is...

Page 85 - VT 100 Network Port Configuration Menu; Select a loop rate of either 56k or 64k.

6 1 2 0 0 . 1 3 0 L 1 - 1 F S U U s e r M a n u a l 7 1 Chapter 7. Configuring the Network Port Figure 7-2 VT 100 Network Port Configuration Menu Interface Type (INT TYPE) Select the connector type for the network interface. The choicesare V.35 and RS232. If the internal DSU is installed, the NETsel...

Page 86 - VT 100 Network Port Frame Relay Options Menu

7 2 F S U U s e r M a n u a l 6 1 2 0 0 . 1 3 0 L 1 - 1 Chapter 7. Configuring the Network Port Clock Source Configure the FSU clocking source as either the master or slave(usually slave). The following physical layer option is available when theselected interface type is V.35 or RS232: Bit Rate Sel...

Page 87 - Set the time between polls to the frame relay network.

6 1 2 0 0 . 1 3 0 L 1 - 1 F S U U s e r M a n u a l 7 3 Chapter 7. Configuring the Network Port Signaling Type (SIGNAL) Set the signaling type option to match the network signalingtype. T391 Set the time between polls to the frame relay network. N391 Determine how many link integrity polls occur in ...

Page 88 - Optional tool for detecting the status of an LLC2 connection.

7 4 F S U U s e r M a n u a l 6 1 2 0 0 . 1 3 0 L 1 - 1 Chapter 7. Configuring the Network Port LLC2 Options (LLC2 OPT) The VT 100 screen in Figure 7-4 appears when LLC2 (LogicalLink Control Type 2) Options is selected from the Network PortConfiguration menu. LLC2 ACK Timeout (ACK TO) Timeout value ...

Page 89 - VT 100 Network Port LLC2 Options Menu

6 1 2 0 0 . 1 3 0 L 1 - 1 F S U U s e r M a n u a l 7 5 Chapter 7. Configuring the Network Port Figure 7-4 VT 100 Network Port LLC2 Options Menu Local IP Address (LOCAL IP ADDR) Enter the internet protocol (IP) address of the FSU Network port. Subnet Mask Enter the subnet number of the network forme...

Page 90 - Process Received RIP Packets

7 6 F S U U s e r M a n u a l 6 1 2 0 0 . 1 3 0 L 1 - 1 Chapter 7. Configuring the Network Port Process Received RIP Packets Enable or disable the FSU's reply to the request from the peerrouters or FRADs to issue RIP messages. Priority Queue Ration (N:1) Define the ratio that SDLC frames have over o...

Page 91 - Chapter 8; IP ROUTING WITH THE FSU

6 1 2 0 0 . 1 3 0 L 1 - 1 F S U U s e r M a n u a l 7 7 Chapter 8. IP Routing Chapter 8 IP Routing IP ROUTING WITH THE FSU The FSU contains an IP router function to resolve paths for IPpackets received. This function is used regardless of encapsula-tion protocol and port received from. The heart of ...

Page 93 - IP Route Table; IP Routing Table Menu

6 1 2 0 0 . 1 3 0 L 1 - 1 F S U U s e r M a n u a l 7 9 Chapter 8. IP Routing IP Route Table Use these menu options to build a table of addresses for routingdata packets based on their IP address. When a packet with thespecified IP address is received, it is sent out through the se-lected port on th...

Page 95 - Enter the port from which the gateway can be reached.

6 1 2 0 0 . 1 3 0 L 1 - 1 F S U U s e r M a n u a l 8 1 Chapter 8. IP Routing Gateway IP Address (GW IP ADD) Enter the Gateway IP address. If an IP packet with an unknownIP address is received, the FSU sends it to the Gateway (which isa router or another FRAD). Gateway Port (GW PORT) Enter the port ...

Page 97 - Chapter 9; SYSTEM CONFIG

6 1 2 0 0 . 1 3 0 L 1 - 1 F S U U s e r M a n u a l 8 3 Chapter 9. System Configuration Chapter 9 System Configuration SYSTEM CONFIG Access System Configuration selections by first choosing 1CONFIGURATION from the Main menu. Then choose SYSTEMCONFIGURATION from the Configuration Menu. Full menutrees...

Page 98 - System Configuration Menu; Change Password

8 4 F S U U s e r M a n u a l 6 1 2 0 0 . 1 3 0 L 1 - 1 Chapter 9. System Configuration Figure 9-1 System Configuration Menu Change Password Enter a new password of nine digits or less. The default pass-word is adtran. Read Community Name (RD COM NAME) Enter the authentication strings used for SNMP ...

Page 101 - Statistics; Viewing Statistical Information with the VT 100 Interface

6 1 2 0 0 . 1 3 0 L 1 - 1 F S U U s e r M a n u a l 8 7 Chapter 10. Statistics Chapter 10 Statistics For descriptions of the VT 100 statistics menus see the followingsection, Viewing Statistical Information with the VT 100 Interface.For front panel menu descriptions, see the section ViewingStatistic...

Page 102 - View Statistics Menu; DTE and Network Port Statistics

8 8 F S U U s e r M a n u a l 6 1 2 0 0 . 1 3 0 L 1 - 1 Chapter 10. Statistics Figure 10-1 View Statistics Menu DTE and Network Port Statistics The following sections describe the information given on theDTE port and Network port statistics menus. See Figures 10-2through 10-5.

Page 105 - DTE Port Statistics Menu-Frame Relay Protocol

6 1 2 0 0 . 1 3 0 L 1 - 1 F S U U s e r M a n u a l 9 1 Chapter 10. Statistics Figure 10-2 DTE Port Statistics Menu-Frame Relay Protocol Figure 10-3 DTE Port Statistics Menu-Transparent Async Protocol

Page 106 - DTE Port Statistics Menu-All Other Protocols

9 2 F S U U s e r M a n u a l 6 1 2 0 0 . 1 3 0 L 1 - 1 Chapter 10. Statistics Figure 10-4 DTE Port Statistics Menu-All Other Protocols Figure 10-5 Network Port View Statistics Menu

Page 107 - DLCI Statistics

6 1 2 0 0 . 1 3 0 L 1 - 1 F S U U s e r M a n u a l 9 3 Chapter 10. Statistics Figure 10-6 View DLCI Statistics Menu-Network Port and Frame Relay Protocol Only DLCI Statistics This menu lists every DLCI number for each frame relay portand classifies it as A (active), I (inactive), or U (unknown). Se...

Page 108 - Protocol Statistics Menu; Hot Keys

9 4 F S U U s e r M a n u a l 6 1 2 0 0 . 1 3 0 L 1 - 1 Chapter 10. Statistics placed in the Other Protocols section and are divided intosignaling frames/bytes and frame/byte totals on the networkside. See Figure 10-7. Figure 10-7 Protocol Statistics Menu Hot Keys Once you have entered one of the st...

Page 109 - Press the F key to freeze the current statistics.

6 1 2 0 0 . 1 3 0 L 1 - 1 F S U U s e r M a n u a l 9 5 Chapter 10. Statistics Protocol Stats (P) - DTE and Network Port Menus only When in any Port Statistics menu, press P to view the ProtocolStatistics menu shown in Figure 10-7. Current Stats (C) Press C to resume viewing current status informati...

Page 110 - Viewing Statistical Information with the Front Panel Interface; RS; Control Signal Status Screen

9 6 F S U U s e r M a n u a l 6 1 2 0 0 . 1 3 0 L 1 - 1 Chapter 10. Statistics Viewing Statistical Information with the Front Panel Interface Select STATS from the Main menu. From this menu, choose toview DTE 1, DTE 2, Network, or System statistics. The firstStatistics screen displays. Scroll throug...

Page 111 - Total received frames since last reset.

6 1 2 0 0 . 1 3 0 L 1 - 1 F S U U s e r M a n u a l 9 7 Chapter 10. Statistics Frames In Total received frames since last reset. Frames Out Total transmitted frames since last reset. Errored Frames Total errored frames received since last reset. Overrun Errors Receive FIFO (first in first out) overr...

Page 112 - Signal State Screen; Total timeouts that have occurred since the last reset.; Total signal errors received since last reset.

9 8 F S U U s e r M a n u a l 6 1 2 0 0 . 1 3 0 L 1 - 1 Chapter 10. Statistics Statistics Available Only for the Network Port The following information is available only when the Networkport is selected from the STATS menu. Signal State Current state of frame relay port (up or down). See Figure 10-9...

Page 113 - to return to the STATS menu.

6 1 2 0 0 . 1 3 0 L 1 - 1 F S U U s e r M a n u a l 9 9 Chapter 10. Statistics System Statistics Select SYS from the STATS menu to display the software versionand checksum. This screen is shown in Figure 10-10. PressCancel to return to the STATS menu. VERSION CHKSUMVER 2.200 17AB Figure 10-10 System...

Page 115 - Diagnostics; DIAGNOSTICS; VT 100 Diagnostics Menu

6 1 2 0 0 . 1 3 0 L 1 - 1 F S U U s e r M a n u a l 1 0 1 Chapter 11. Diagnostics Chapter 11 Diagnostics DIAGNOSTICS This menu allows you to perform diagnostics by sending pingrequests and performing loopback tests. See Figure 11-1 for theVT 100 Diagnostics menu. See Figure 11-2 for the Front Panelm...

Page 116 - Front Panel Diagnostics Menu; Ping

1 0 2 F S U U s e r M a n u a l 6 1 2 0 0 . 1 3 0 L 1 - 1 Chapter 11. Diagnostics 1 PINGS SENT 1 PING ADDRESS 2 RESPONSES 1 PING 2 START PING 3 MIN TIME 3 DIAG 4 MAX TIME 2 LOOPBACK DISENA 5 AVG TIME Figure 11-2 Front Panel Diagnostics Menu Ping Select 1 PING to send a ping request to a specific add...

Page 119 - Appendix A

6 1 2 0 0 . 1 3 0 L 1 - 1 F S U U s e r M a n u a l 1 0 5 Appendix A. Pinouts Appendix A Pinouts The following tables give the pin assignments for the connectorslocated on the back of the FSU. For more information on theconnectors, see the chapter Installation.

Page 120 - DTE/DCE Connector Pin Assignments

1 0 6 F S U U s e r M a n u a l 6 1 2 0 0 . 1 3 0 L 1 - 1 Appendix A. Pinouts Table A-A DTE/DCE Connector Pin Assignments DB25 Pin# V.35 Pin# Function DTEx Port Direction DCE Port Direction 1 A FGND 2 TD(RS232) I O 3 RD(RS232) O I 4 C RTS I O 5 D C T S O I 6 E D S R O I 7 B GND 8 F D C D O I 9 NEG 1...

Page 121 - Main Connector Pin Assignments; Control Connector Pin Assignments; female V.35 connector

6 1 2 0 0 . 1 3 0 L 1 - 1 F S U U s e r M a n u a l 1 0 7 Appendix A. Pinouts Table A-B Main Connector Pin Assignments Pin Name Description 1 R1 Transmit Data from DSU to Network-Ring 1 2 T1 Transmit Data from DSU to Network-Tip 1 3-6 - Not Used 7 T Receive Data from Network to DSU-Tip 8 R Receive D...

Page 123 - Appendix B; SPECIFICATIONS AND FEATURES; Frame relay utilizing DDS or FT1 circuits

6 1 2 0 0 . 1 3 0 L 1 - 1 F S U U s e r M a n u a l 1 0 9 Appendix B. Specifications Summary Appendix B Specifications Summary SPECIFICATIONS AND FEATURES This section describes the standard specifications and featuresincorporated in the FSU. Operating Modes Frame relay utilizing DDS or FT1 circuits...

Page 124 - Each DTE interface may be assigned one of the following

1 1 0 F S U U s e r M a n u a l 6 1 2 0 0 . 1 3 0 L 1 - 1 Appendix B. Specifications Summary DCE & DTE Interfaces RS-232V.35 via adapter cable SNMP Internal SNMP agentMIB II RFC 1213Frame relay DTE MIB RFC 1315ADTRAN enterprise MIBTelnet Access Clocking Normal DDS or private network tributary (s...

Page 125 - CSU and DSU loopbacks

6 1 2 0 0 . 1 3 0 L 1 - 1 F S U U s e r M a n u a l 1 1 1 Appendix B. Specifications Summary Diagnostics Network CSU and DSU loopbacks User All Port Loopback ModePing Test Mode Line Line Requirements Loop transmission parameters as defined in:AT&T PUB 62310: Dedicated DDS Line Interface RJ-48S, ...

Page 126 - Operating temperature: 0 to 50

1 1 2 F S U U s e r M a n u a l 6 1 2 0 0 . 1 3 0 L 1 - 1 Appendix B. Specifications Summary LLC ANSI/IEEE 802.2 PPP RFC 1661RFC 1662 SLIP RFC 1055 SNMP MIB RFC 1315RFC 1213 Environment Operating temperature: 0 to 50 o C (32 to 122 o F) Storage: -20 to 70 o C (-4 to 158 o F) Relative humidity: Up to...

Page 127 - Acronyms and Abbreviations; phony and Telegraphy

6 1 2 0 0 . 1 3 0 L 1 - 1 F S U U s e r M a n u a l 1 1 3 Acronyms and Abbreviations Acronyms and Abbreviations ACK ........................................................ acknowledgmentANSI ....................................................... American National Standards InstituteAR ...............

Page 131 - Glossary; American National Standards Institute (ANSI)

6 1 2 0 0 . 1 3 0 L 1 - 1 F S U U s e r M a n u a l 1 1 7 Glossary Glossary 2-wire Switched 56 A Northern Telecom proprietary 56 kbps switched digital data service offered bytelco service providers, and delivered to users over a single pair of copper wires.Compatible with the ADTRAN DSU III S2W and ...

Page 133 - See Channel Service Unit.

6 1 2 0 0 . 1 3 0 L 1 - 1 F S U U s e r M a n u a l 1 1 9 Glossary CRC Cyclic redundancy check. A computational means to ensure the accuracy offrames transmitted between devices in a frame relay network. The mathematicalfunction is computed, before the frame is transmitted, at the originating device...

Page 134 - DSU

1 2 0 F S U U s e r M a n u a l 6 1 2 0 0 . 1 3 0 L 1 - 1 Glossary data link connection identifier (DLCI) A unique number assigned to a PVC end point in a frame relay network.Identifies a particular PVC endpoint within a user's access channel in a framerelay network and has local significance only t...

Page 135 - file server

6 1 2 0 0 . 1 3 0 L 1 - 1 F S U U s e r M a n u a l 1 2 1 Glossary file server In the context of frame relay network supporting LAN-to-LAN communications,a device connecting a series of workstations within a given LAN. The deviceperforms error recover and flow control functions as well as end-to-end...

Page 136 - hop

1 2 2 F S U U s e r M a n u a l 6 1 2 0 0 . 1 3 0 L 1 - 1 Glossary hop a single trunk line between two switches in a frame relay network. Anestablished PVC consists of a certain number of hops, spanning the distance formthe ingress access interface to the egress access interface within the network. ...

Page 137 - packet

6 1 2 0 0 . 1 3 0 L 1 - 1 F S U U s e r M a n u a l 1 2 3 Glossary packet A message containing both control information and data. The controlinformation is used for routing the packet through a network to its finaldestination. Contrast with frame relay frame. packet-switching network A telecommunica...

Page 139 - synchronous

6 1 2 0 0 . 1 3 0 L 1 - 1 F S U U s e r M a n u a l 1 2 5 Glossary synchronous Communications in which the timing is achieved by sharing a single clock. Eachend of the transmission synchronizes itself with the use of clocks andinformation sent along with the transmitted data. synchronous data link c...

Page 141 - Index; Symbols

6 1 2 0 0 . 1 3 0 L 1 - 1 F S U U s e r M a n u a l 1 2 7 Index Index Symbols 56/64 DDS DSU 2, 3, 5, 69 A abort 20abort changes 20abort frames 97aborts rcv 90Ack TO network port 74 activating menu items 16adapter cable 8ADD key 11, 12add new entry bisync protocol 56frame relay protocol 46IP routing ...

Page 153 - Product Support Information

Product Support Information Pre-sales Inquiries and Applications Support Please contact your local distributor, ADTRAN ApplicationsEngineering, or ADTRAN Sales: Applications Engineering (800) 615-1176Sales (800) 827-0807 Post-Sale Support Please contact your local distributor first. If your local di...

ADTRAN 1200130L1 - Manual

Table of Contents:

Summary

Other ADTRAN Models