Page 2 - Table of Contents
Table of Contents Important Safety Instructions ................................................... 1 Battery Cautionary Instructions ............................................... 3 Features ..................................................................................... 5 Installation .........
Page 3 - Important Safety Instructions
Important Safety Instructions When using your telephone equipment, basic safety pre- cautions should always be followed to reduce the risk of fire, electrical shock, and injury to persons including the following: 1. Read and understand all instructions. 2. Follow all warnings and instructions marked...
Page 4 - SAVE THESE INSTRUCTIONS
this product, but take it to a qualified serviceman when some service or repair work is required. Opening or removing covers may expose you to dangerous voltages or other risks. Incorrect reassembly can cause electric shock when the appliance is subsequently used. 10. Unplug this product from the wa...
Page 5 - Battery Cautionary Instructions
Battery Cautionary Instructions CAUTION - To Reduce the Risk of Fire or Injury to Persons, Read and Follow these Instructions. 1. Use only the following type and size of battery: Four (4) AAA size 1.5 volt (24A) carbon zinc or alkaline batteries. 2. Do not dispose of the battery in a fire. The cell ...
Page 7 - Features; Telephone Features
Features Congratulations on your purchase of the AT-200HT headset telephone with Caller-ID. This product allows you to take advan- tage of the Caller ID service available from your telephone com- pany. If you do not already have this service, you must contact the telephone company and have it instal...
Page 8 - Installation; Getting Started; Battery Installation; phone line before inserting or replacing batteries.; NEW CALL; Proceed immediately to set the display lan-
Installation Getting Started Unpack the unit and check to make sure you have all the items that come with your telephone. • AT-200HT headset telephone. • Headset with cord. • 7 foot long telephone line cord. • Belt Clip Battery Installation The AT-200HT requires the installation of four AAA size, 1....
Page 9 - will appear and the letter; Figure 2
Figure 1 Setting the Display Language After inserting the battery and connecting the handset coiled cord, "SET LANGUAGE" will appear and the letter "E" will flash in the display for 30 seconds. Figure 2 ENGLISH Use tip of ball point pen to remove the battery cover Belt clip 7
Page 11 - Setting the Time and Date; not necessary
1. Press the review ! or q buttons as required to set the first digit of your area code. Press the ERASE button to move to the second digit. 2. Press the review ! or q buttons as required to set the sec- ond digit of your area code. Press the ERASE button to move to the third digit. 3. Press the rev...
Page 12 - ERASE; Installing the Belt Clip; HEADSET
4. Press and hold the ERASE button, then press the review "# button while in Stand-By Screen mode. Installing the Belt Clip A belt clip has been supplied with your headset telephone. It can be easily installed or removed as required. See Figure 1 1. Insert the belt clip mounting tabs into the co...
Page 13 - Figure 3; With one hand grasp the cushioned speaker and carefully
Figure 3 3. With one hand grasp the cushioned speaker and carefully pull the microphone boom downward. Adjust it into position so that the microphone is in front of or slightly to the side of your mouth. 4. The microphone boom is flexible so that it can be bent to position it approximately 1 to 2 in...
Page 15 - Figure 5
1. Connect one end of the telephone line cord (supplied) into the TEL. LINE jack located at the rear of the unit. 2. Connect the remaining end of the telephone line cord into an existing telephone wall jack. Telephone Jack Headset Jack Tel. Line Jack 13 Figure 5
Page 16 - Operation; Setting the Tone/Pulse switch; TONE; Figure 6; RINGER
Operation Setting the Tone/Pulse switch The AT-200HT telephone can operate in tone or pulse dialing mode. 1. Set the PULSE/TONE switch located on the side of the telephone to the desired position. See Figure 6 2. If you're not sure which service you have, set the PULSE/ TONE switch to the TONE posit...
Page 17 - Figure 7; Making Calls; TALK
1. Set the ringer OFF/LOW/HI switch to the LOW position to lower the ringer sound level. 2. Set the ringer OFF/LOW/HI switch to the OFF position to turn off the ringer sound completely. Figure 7 Making Calls To make a call, put on the headset and adjust it for your comfort. 1. Adjust the headset mic...
Page 18 - button to hang; Figure 8
5. The number being dialed will be appear in the display. 6. When called party answers, begin speaking normally into the headset microphone. 7. After completing your call, push the TALK button to hang up. The IN USE/MUTE LED will go out. Receiving Calls IMPORTANT: Allow at least two rings to occur p...
Page 19 - Using the Redial button
1. The NEW CALL icon will appear on the display. 2. If you choose not to answer the call, after approximately 15 seconds after the last ring is received, the display will change to Stand-By Screen mode. 3. The NEW CALL LED will flash, confirming new calls have been received. 4. The Stand-By Screen w...
Page 21 - Using the Call Timer; Using the Pause feature; REDIAL; Reviewing Call Records
Using the Call Timer The AT-200HT has a built in timer that will automatically begin to indicate length of your call five seconds after pressing the TALK button to make or receive a call. The call timer will turn off after you press the TALK button again to hang up. Using the Pause feature The pause...
Page 23 - Line Error; The display will indicate; Out of Area Calls; When a call is received from someone whose area code does
Line Error The display will indicate "LINE ERROR" if a call is received that has an error in the transmission or reception of data. Important: Always wait for at least two rings to occur prior to answering a call. Out of Area Calls When a call is received from someone whose area code does no...
Page 24 - Erasing Individual Calls; Erasing All Calls
Erasing Individual Calls When reviewing the call records, any individual call can be deleted by quickly pressing the ERASE button twice within one second. 1. The displayed call record will be erased and the new call re- cord will appear in the display. 2. A call record cannot be retrieved once it ha...
Page 25 - Low Battery Indication; The
Low Battery Indication The "LOW BATTERY" icon is displayed when the battery volt- age is low or if the batteries are not installed. When changing the batteries, the unit will retain programming and stored call records for about 15 seconds. If you take longer, you will have to reprogram your ...
Page 26 - Care and Maintenance
24 Care and Maintenance Your AT-200HT Caller-ID telephone has been designed to give years of trouble free service. To assure its longevity, please read the following maintenance instructions. 1. Keep away from heat, high temperatures can shorten the life of the electrical components as well as disto...
Page 27 - Troubleshooting; Have Dial Tone but Cannot Dial Out.
25 Troubleshooting No Dial Tone. • The telephone line cord is not plugged in properly at the telephone jack or at the telephone. • Test the telephone using a different telephone jack, if it works, the first jack may be defective. Have Dial Tone but Cannot Dial Out. • Check that the PULSE/T ONE switc...
