3M MT7 - Manual

3M MT7

3M MT7 – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.

1 Page 1
2 Page 2
3 Page 3
4 Page 4
5 Page 5
6 Page 6
7 Page 7
8 Page 8
9 Page 9
10 Page 10
11 Page 11
12 Page 12
13 Page 13
14 Page 14
15 Page 15
16 Page 16
17 Page 17
18 Page 18
19 Page 19
20 Page 20
21 Page 21
22 Page 22
23 Page 23
24 Page 24
25 Page 25
26 Page 26
27 Page 27
28 Page 28
29 Page 29
30 Page 30
31 Page 31
32 Page 32
33 Page 33
34 Page 34
35 Page 35
36 Page 36
37 Page 37
38 Page 38
39 Page 39
40 Page 40
41 Page 41
42 Page 42
43 Page 43
44 Page 44
45 Page 45
46 Page 46
47 Page 47
48 Page 48
49 Page 49
50 Page 50
51 Page 51
52 Page 52
53 Page 53
54 Page 54
55 Page 55
56 Page 56
57 Page 57
58 Page 58
59 Page 59
Page: / 59

Table of Contents:

  • Page 3 – Contents
  • Page 4 – Chapter 5
  • Page 5 – About This Manual; Introduction; CAUTION
  • Page 6 – M Touch Systems Support Services
  • Page 7 – C H A P T E R 1; Installing MT 7 Software; MT 7 Software Overview; Touch Drivers
  • Page 8 – Whether you hear a sound when you touch the sensor.; Online Help; For Linux® use; Multiple Display Manager; Typical Install (basic features needed to support touch)
  • Page 9 – To install MT 7 software:; Driver Selection
  • Page 10 – User Interface; The User Interface provides the following components:
  • Page 11 – Utilities and Tools; Performing a Silent Install
  • Page 12 – Customizing Your Settings
  • Page 13 – C H A P T E R 2; MT 7 Software Control Panel; Overview; You can open the MT 7 control panel by clicking:; use StartCP; to launch the control panel
  • Page 14 – Main Tab; Calibration; You should calibrate the sensor in the following cases:
  • Page 15 – Calibrating the Sensor
  • Page 16 – Testing the Calibration; Support Information; Controller ID
  • Page 17 – Controller Type
  • Page 18 – Touch Settings Tab; Touch Modes
  • Page 19 – Touchdown Mode; Touch Sound
  • Page 20 – Edge Adjustment Tab
  • Page 21 – Edge Adjustment Setting
  • Page 23 – Tools Tab; Component Versions
  • Page 24 – Draw Test; You must be in Draw mode for this to work properly.; Restore Factory Settings; Software
  • Page 25 – Reset Controller; Important Note; : Executing the Advanced Options may alter the performance of your
  • Page 26 – Controller Tab
  • Page 27 – Linearization; Linearization Process
  • Page 28 – To exit this program at any time during the process, press Escape.
  • Page 29 – Sensor Frequency; This option applies to capacitive EX series controllers.
  • Page 30 – Changing this field will affect your multiple display setup.
  • Page 31 – C H A P T E R 3; Windows® CE Overview; Installation Instructions; Go to
  • Page 32 – Welcome
  • Page 33 – Select Installation Folder
  • Page 34 – Confirm Installation
  • Page 35 – Instructions for Platform Builder for Microsoft Windows® CE 6.0 R3; Device Drivers
  • Page 36 – Supporting Multiple Windows® CE Versions
  • Page 37 – Slow Draw Anomalies
  • Page 39 – C H A P T E R 4; Windows® XP Embedded Overview
  • Page 40 – MT 7 Components
  • Page 41 – C H A P T E R 5; MT 7 for Linux® Overview; System Requirements; Hardware Prerequisites
  • Page 42 – Before Driver Installation; MT 7.13 Build 3 only supports X Server releases of rev 1.10 and before.; General Instructions; su
  • Page 43 – Normal Installation; or; Installing on Write-Protected Systems
  • Page 44 – UdevDir; InitDir h
  • Page 45 – the appropriate path.; XorgDir; and; Error Messages During Installation; Not all will be the same depending on which version you are running
  • Page 46 – The second method is to edit the var-file. Copy the file
  • Page 47 – script. If it cannot find any of these, this message; TWDrvStartup; Removing MT 7 For Linux
  • Page 48 – Troubleshooting Touch Behavior
  • Page 49 – Calibration Messages Are Unreadable; xlsfonts; command or other suitable utility that; export MT7FontSansSerif; If you find a suitable font, change your system login script, such as; Known Issues
  • Page 51 – A P P E N D I X A
  • Page 55 – A P P E N D I X B; Troubleshooting the Touch System
  • Page 56 – Multiple Display Support; Cursor Jumps or Bounces Suddenly Across the Display
  • Page 57 – Drawing Lines Are Not Straight and Smooth; This option applies to Windows® only.; Touch Is Not Working
  • Page 58 – Check the following items:; Touch Driver Did Not Load; Between these two lines, add a new line:
  • Page 59 – A Previous Version of TouchWare Software Was Detected; Programs
Loading the manual

3M Touch Systems, Inc. Proprietary Information – 25695M

3M

™

MicroTouch

™

Software MT 7

User Guide

For Microsoft® Windows®, Windows® CE,

and Linux® Operating Systems

Read and understand all safety information

contained in this document before using this product.

3

"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.

Summary

Page 3 - Contents

3M™ MicroTouch™ Software MT 7 User Guide 3 3M Touch Systems, Inc. Proprietary Information – 25695M Contents About This Manual Introduction ................................................................................................................ 5 Sensor Care and Cleaning ........................

Page 4 - Chapter 5

4 3M™ MicroTouch™ Software MT 7 User Guide 3M Touch Systems, Inc. Proprietary Information – 25695M Chapter 5 MT 7 for Linux® Overview System Requirements ............................................................................................... 41 Installation Instructions ........................

Page 5 - About This Manual; Introduction; CAUTION

3M™ MicroTouch™ Software MT 7 User Guide 5 3M Touch Systems, Inc. Proprietary Information – 25695M About This Manual Introduction This manual describes how to: • Install 3M™ MicroTouch™ Software MT 7 for your touch system and specific operating system. • Use the MT 7 control panel to customize your ...

Other 3M Models

All 3M Other