3Com LANplex 6000 - Manual
3Com LANplex 6000 – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 2 – TRSM Description; TRSM Configurable; Stores and forwards packets from one attached LAN to another
- Page 3 – Transparent traffic is not forwarded while in this mode.
- Page 4 – TRSM Installation; Getting Started; Safety Information; Read if installing in
- Page 5 – To remove the faceplate:; Figure 1; LANplex 6004 with Blank Faceplates; Pull the faceplate away from the system.; Read if replacing; you can correctly re-connect them to the new module.
- Page 6 – Figure 2; Handles in Outward Position; Remove the module from the system.; Installing the TRSM; Only the LMM may be inserted in slot one of the LANplex system. The
- Page 7 – Figure 3; Ground Symbol for Static Discharge; Remove the TRSM from its antistatic bag.; Figure 4
- Page 8 – If the system is powered on when you are installing a module,; Figure 5; Guiding an TRSM Module into a LANplex 6012
- Page 9 – Figure 6; Guiding an TRSM Module into a LANplex 6004
- Page 10 – Figure 7; Tighten the TRSM’s securing screws using a flat-blade screwdriver.
- Page 11 – LED Activity; For 3Com Technical Support information, see Appendix B: Technical
- Page 12 – TRSM Components; Figure 8; TRSM Option Module
- Page 13 – Status LEDs; Each TRSM contains two; Module Status; LEDs and eight; Port Status
- Page 14 – Pin Assignments
- Page 15 – Documentation Comments; Please include the following information when commenting:
R
T
OKEN
R
ING
S
WITCHING
M
ODULE
I
NSTALLATION
G
UIDE
For the LANplex 6000
About This Guide
This guide includes:
■
An inventory of items shipped with your LANplex 6000 module
■
An overview of the Token Ring Switching Module ( TRSM)
■
Instructions for installing and replacing TRSM
■
A description of the TRSM’s components, including media options and
diagnostic LEDs
■
Pin-out information for the TRSM
Information on installing modules is also included in the
LANplex 6000
Getting Started
guide.
NOTE:
Prior to installing the TRSM module, LANplex system software revision
6.0 or later must be installed.
CAUTION:
In order to run software revision 5.0 or later on the LANplex 6000
you must have the new LMM Plus installed in your system. To verify if you
have an LMM Plus installed check the module’s ejector tab to ensure it says
LMM+
.
Audience
This guide is intended for trained technical personnel only.
Taking Inventory
Your package should contain the following items.
■
1 LANplex 6000 TRSM
■
1
LANplex 6000 Software Release Notes
■
1 disposable electrostatic discharge (ESD) wrist strap
■
Operational diskette(s) (UNIX and DOS)
■
MIB diskette(s) (UNIX and DOS)
Contact 3Com Customer Service Organization at 1-800-876-3266, option 2,
if any item is missing.
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
2 TRSM Description TRSM Description The Token Ring Switching Module ( TRSM) is designed to add Token Ring ( TR) switching functionality to the LANplex 6000, providing the most cost effective solution for introducing segmentation for today's Token Ring networks, while allowing you to prepare for futu...
TRSM Description 3 nonvolatile RAM so they will survive a power loss or system initialization. Source Routed traffic is not forwarded while in this mode. Source Routing (SR) In Source Routing (SR), the packet contains information in the Route Information Field (RIF), which specifies the route the pa...
4 TRSM Installation TRSM Installation This section describes the following: ■ Module safety information ■ Installation information ■ LED activity during installation ■ Pin-out information Information on installing modules is also included in the LANplex 6000 Getting Started guide. Safety Information...
