Page 4 - TABLE OF CONTENTS
IMPORTANT SAFETY INFORMATION 1 WALL HOOD INSTALLATION 4 DESIGNER WALL HOOD INSTALLATION 11 CROWNSOUND ™ INSTALLATION 16 REMOTE BLOWER INSTALLATION 18 OPERATION 20 CHANGING PARTS 21 FREQUENTLY ASKED QUESTIONS 32 TROUBLESHOOTING 35 WARRANTY 38 TABLE OF CONTENTS
Page 5 - IMPORTANT SAFETY INFORMATION; for the safety of your home and the people living in it.
1 Gener al Safet y IMPORTANT SAFETY INFORMATION WARNING If the information in this manual is not followed exactly, a fire or explosion may result causing property damage, personal injury, or death. • Before beginning installation, please read and follow these important instructions for the safety of...
Page 6 - the duct to prevent back drafting.
2 Gener al Safet y • Sufficient air is needed for proper combustion and exhausting of gases through the duct to prevent back drafting. • Before servicing or cleaning the unit, fully disconnect the range hood from power to avoid risk of electric shock and injury. • Ducted range hoods MUST ALWAYS be v...
Page 7 - and meet industry standards and regulations.
3 Gener al Safet y • When cleaning stainless steel, only use a stainless steel cleaner product with a soft sponge, or use a cloth with a warm soap and water solution. Never use abrasive powders or liquids. • To reduce the risk of fire and to disperse air properly, make sure to vent air outside. DO N...
Page 8 - WALL HOOD INSTALLATION
4 W all Hood Measur ements 30”-36” 36” Height V aries 16”-max 3 1½” NOTE: The recommended height to install your hood is 30˝ minimum and 36˝ maximum above the range top or cook top. For outdoor range hood installation, the unit must be installed at a minimum of 36˝ and a maximum of 42” above the gri...
Page 10 - Ducting; DUCTING
6 Ducting DUCTING NOTES: • Ducting is not provided with your ZLINE range hood. It’s recommended to use solid ducting made of galvanized steel or another appropriate rigid metal ducting whenever possible for the lowest noise and highest flow. • Use a maximum of 40’ of ductwork. Try to minimize the us...
Page 11 - MOUNTING DIRECTIONS
77 Mounting Dir ections MOUNTING DIRECTIONS 1. Based on the width of your hood, measure to find the center of the wall. Mark a line and measure to the left and right to find your two mounting points. Make sure the mounting points are level and mark the with a pen. It is recommended to install the ho...
Page 12 - Ducting and Electrical Connections
8 5. Install the transition piece on top of the range hood by securing it with screws (E) provided. Some hoods require 4 screws, others require 6. Figure 4 6. Secure your ducting connection to the transition piece using foil-backed tape to hold it into place top of the hood. Try and minimize the use...
Page 13 - Figure 7
99 Installing th e Chimney 8. Install the two-part telescoping chimney on top the hood. Slide the inside section up until the vertical vent slots are visible, then attach the top portion to the mounting bracket with 2 screws (F). Secure the lower portion to the hood with 2 screws (F). NOTE: Screw (E...
Page 14 - Figure 9; Cr
10 10 If you purchased specialty crown molding to install with your range hood, follow these instructions before attaching the ducting and chimney sections.1. Secure the crown molding bracket to the ceiling directly above the range hood by using the hardware provided with the crown molding (note: fo...
Page 15 - Designer W; DESIGNER WALL HOOD INSTALLATION
11 30”-36” 36” Height V aries Max 36” Scan for a designer wall hood installation tutorial video 11 Designer W all Hood Measur ements DESIGNER WALL HOOD INSTALLATION
Page 18 - Figure 3
14 14 Ducting and Electrical Connections 5. Install the transition piece on top of the range hood by securing it with screws (E) provided. Some hoods require 4 screws, others require 6. Figure 3 6. Secure your ducting connection to the transition piece using foil-backed tape to hold it into place to...
Page 19 - by using the hardware provided with the crown molding.
15 15 Installing th e Chimney 8. After precisely measuring the distance between the top of the range hood and your ceiling, have a trained professional cut your one-piece designer chimney to the desired length; you must leave a 2 1/4” gap between the chimney and ceiling in order to install the crown...
Page 20 - ELECTRIC POWER RATING; Installation Tutorial Video; Recirculating your range hood is not possible with CrownSound; chimney. When the connection is successful, a chime will sound.; CROWNSOUND
16 ELECTRIC POWER RATING Frequency: 120VAC/60 HZPower: 10W NOTE: Installation Tutorial Video Recirculating your range hood is not possible with CrownSound ™ installation. 1. Attach crown molding bracket to ceiling using hardware provided. Figure 1 Figure 1 2. Attach ducting and electrical connection...
Page 21 - Figure 4; moldings carry a one-year parts warranty. Replacement speakers
17 3. Extend the chimney up to the transformer. Slide the crown molding onto the crown bracket and secure into place. The crown should cover the gap. Ensure that it installs properly and is level. Figure 3 Figure 3 4. Open the phone’s Bluetooth settings and find “ZLINE Audio.“ When the connection is...
Page 22 - Remote Blower Installation; hood installed in your kitchen.; REMOTE BLOWER INSTALLATION
18 18 Remote Blower Installation If you’ve purchased a remote blower-type range hood, please use the following installation instructions. Before beginning installation, be sure to connect the electrical cord to the hood and plug the blower motor in to test the unit. You will find the power cord insi...
Page 23 - Remote Blower Ducting; Unit Connection Cord; T85 Remote Blower — Single Motor
19 19 Remote Blower Ducting REMOTE BLOWER INSTALLATION Unit Connection Cord Unit Connection Cord Single and dual-motor remote blowers are designed to reduce noise by installing them in a separate location inside the home, up to 20’ away from the range hood. T85 Remote Blower — Single Motor This moto...
Page 24 - Turn ON/OFF the range hood and activate the power-off delay timer.; Turn ON/OFF the range hood and activate power-off delay timer.; ation; OPERATION
20 Button functions (some models have different control panel layouts): Button Control Panel Operational Manual ! ! ! Power Power-Off Delay Low Speed Medium 1 Speed Light High SpeedMedium 2 Speed Blower Speed Indicator Power: Turn ON/OFF the range hood and activate the power-off delay timer. Light: ...
Page 25 - Replacing th; CHANGING PARTS
21 HOW TO REPLACE THE BUTTON PANEL 1. Remove baffle filters from underneath the hood. 2. Locate the back of the button panel. 3. Remove screws from each side of the button panel. 4. Disconnect the panel from the cord connecting to the circuit board, an overlay of which is included below. WARNING Nev...
Page 27 - Replacing Light Bulbs; HOW TO REPLACE THE LIGHT BULBS IN YOUR RANGE HOOD
23 23 Replacing Light Bulbs HOW TO REPLACE THE LIGHT BULBS IN YOUR RANGE HOOD 1. Turn the power off at the breaker and unplug the range hood.2. Remove baffle filters from underneath the hood.3. Squeeze the LED light assembly out until it falls out of the socket as noted in the images below. 4. Disco...
Page 29 - HOW TO REPLACE THE TRANSFORMER
25 25 Replacing th e T ransformer CHANGING PARTS HOW TO REPLACE THE TRANSFORMER 1. Turn the power off at the breaker and unplug the range hood.2. Remove screws from the circuit board (circled in blue) cover in a similar fashion. Figure 1 3. Locate the wire coming from the transformer (circled in pin...
Page 30 - SINGLE MOTOR ELECTRICAL DIAGRAM
26 26 Electrical and Cir cuit Boar d Diagr am CHANGING PARTS SINGLE MOTOR ELECTRICAL DIAGRAM ground ground
Page 32 - Replacing Baffle Filter; HOW TO REPLACE PROFESSIONAL SERIES BAFFLE CHANNELS AND FILTERS; The baffle channels may already be in place.
28 28 Replacing Baffle Filter s CHANGING PARTS HOW TO REPLACE PROFESSIONAL SERIES BAFFLE CHANNELS AND FILTERS Covering models 696, 697, and KECOM. ZLINE’s professional series range hoods are equipped with two removable dishwasher-safe baffle channels in which the filters rest. To install the channel...
Page 33 - HOW TO REPLACE SPRING-LOADED BAFFLE FILTERS; Release
29 29 Replacing Baffle Filter s CHANGING PARTS WARNING Edges on the baffle filters and baffle channels may be sharp — please use caution when installing and removing. Use of gloves during installation is highly recommended. Do not attempt to disassemble baffle filters, as the process may result in i...
Page 34 - HOW TO REPLACE OR CHANGE CHARCOAL FILTERS
30 30 Replacing Char coal Filter s CHANGING PARTS HOW TO REPLACE OR CHANGE CHARCOAL FILTERS It is recommended to use ducting to direct vent your range hood whenever possible If your situation does not allow for a direct vent installation, carbon filters are available to recirculate the air through y...
Page 35 - HOW TO CLEAN AND REPLACE THE GREASE CUP; Slide into place
31 31 Replacing th e Gr ease Cup CHANGING PARTS HOW TO CLEAN AND REPLACE THE GREASE CUP A removable plastic grease cup is designed to catch excess grease at the bottom of the motor. It’s recommended to remove it every 2-3 months, wash it, then re-install it. To remove or install the grease cup, remo...
Page 36 - Are ZLINE range hoods considered type 1 or type 2?; FREQUENTLY ASKED QUESTIONS
32 32 Frequently Ask ed Questions Are ZLINE range hoods considered type 1 or type 2? Type 1 — these types of range hoods are used with ranges, cook tops, and appliances that produce grease and smoke. Why is my range hood white? This is a protective layer that is placed on all ZLINE range hoods to pr...
Page 37 - No — unfinished wood range hoods are only compatible with paint.
33 33 Fr equently Ask ed Questions Can my hood be ductless? It is better to duct your range hood to the outside, but if this is not possible, ductless is an acceptable alternative. Many ZLINE range hoods have the capability to be converted to ductless. Ductless is when the air circulates through cha...
Page 38 - Only 1 device can sync at a time.
34 34 Frequently Ask ed Questions How do I clean my baffle filters and how often? Your baffle filters should be washed with hot water and soap once per month or placed in a dishwasher for cleaning. Make sure filters are completely dry before reinstalling. Re-place the filters if they become damaged ...
Page 39 - TROUBLESHOOTING; ISSUE
35 Tr oublesh ooting TROUBLESHOOTING ISSUE POSSIBLE CAUSE SOLUTION “ZLINE Audio” won’t appear in the Bluetooth settings. Check if the electrical connections are secure. A chime will sound if the connection is successful. Turn off and on your smart phone’s Bluetooth settings to allow time for the Cro...
Page 41 - Outdoor units should be at least 1 size larger, if not 2.
37 Tr oublesh ooting TROUBLESHOOTING ISSUE POSSIBLE CAUSE / SOLUTION My range hood is not pulling. Was the unit plugged in and was the fan checked before installation? What distance is the hood mounted above the cook top? Make sure the distance is 30”-36” (indoor) or 36”-42” (outdoor). Is the range ...
Page 42 - WARRANTY
COVERAGE ZLINE Kitchen and Bath range hood parts will be warrantied for three years from the original purchase date for the original purchaser of the product. ZLINE will provide free-of-charge, non-consumable replacement parts for the components that failed due to manufacturing defects. Additionally...
