Yazoo/Kees ZMB142180, ZMB148180, ZMKW48170, ZMKW48190, ZMKW48210, ZMKW52230, ZMKH52230, ZMKW61230 - Manual

6 SYMBOLS AND DECALS Symbols and Decals These symbols are found on the machine and in the operator’s manual.Study them carefully so that you know what they mean. WA RNING !X xx xx xx xx xx xx xx xx x x xx x xX xx xx xx xx xx xx .xx xx xx x xx x x xx xx xx x x x. Used in this publication to notify th...

7 SAFETY INSTRUCTIONS Safety Instructions These instructions are for your safety. Read them carefully. WARNING! This symbol means that important safety instructions need to be emphasized. Itconcerns your safety. General Use • Read all instructions in this operator’s manualand on the machine before s...

9 6003-004 Mow up and down, not side-to-side. Driving on Slopes SAFETY INSTRUCTIONS Driving on slopes is one of the operations wherethe risk is greatest that the driver will lose controlor the machine will tip over, which can result inserious injury or death. All slopes require extracaution. If you ...

12 • Never use the machine indoors or in spaces lacking proper ventilation. The exhaust fumes contain carbon monoxide, and odorless, poi- sonous, and lethal gas. • Stop and inspect the equipment if you run over or into anything. If necessary, make repairs before starting. • Never make adjustments wi...

13 PRESENTATION Presentation Thank you for buying YAZOO/KEES! Before operating your new mower, read, understandand follow the safety instructions and otherdirections in this manual. Lawnmowers and all power equipment, can bepotentially dangerous if used improperly.Safety requires good judgement, car...

14 SETUP AND ADJUSTMENTS WARNING: No settings or adjustments areto be made unless: Engine is stopped, keyhas been removed, park brake is on andbattery cable removed from battery. Setup Uncrate machine. Mount rear drive wheels using the lug nutsinstalled on the hubs. Check the tire pressure in all fo...

15 SETUP AND ADJUSTMENTS Mower Deck Leveling Position machine on a flat surface. Preferablylevel concrete. Check the tire pressure in all four tires. Inflationshould be 15 psi. Place 2x4’s on edge under the cutting deck fromfront to rear and lower the deck down onto2x4’s. Adjust the four upper chain...

16 SETUP AND ADJUSTMENTS Motion Control Linkage Adjustment This adjustment must be made with the rearwheels rotating. Raise the rear of the machineand block it up so the wheels are free to rotate. CAUTION: Keep hands, feet and clothingaway from rotating tires. Tilt seat forward and remove the seat r...

17 OPERATION Motion Control Lever Pattern (Right Side) FIG - 8 Run engine full throttle to make sure wheels donot rotate. Readjust if any rotation occurs. Repeat the whole process for the opposite sideand tighten the nuts against the ball joints. Turn machine off. Reinstall the seat rod and check th...

18 By moving the levers an equal amount forwardor back the machine will move in a straight linein that direction. FIG - 9. Movement of either lever forward will cause theright or left wheel to rotate in a forward direction.To stop movement pull both levers into theneutral position. To turn right whi...

19 Fuel shut off valve is located at the right rear of theseat. The valve has three positions a right tank, lefttank and center is the off position. FIG - 11. The pump release valves are located at the rightfront corner of the pumps. Used to release thesystem so the machine may be moved by handwhen ...

20 Hardware Check daily. Inspect the entire machine forloose or missing hardware. Air filter See engine manufacturers specifications forcleaning and replacement intervals. Hydraulic system Check oil level in tank daily. Oil level should be3/4” to 1” below the top of the tank. Check allfittings, hose...

23 Maintenance Schedule Maintenance Maintance Interval (hours)Daily 25 50 100 200 250 500 Engine (4) Check oil level X Change oil and filter (1)Clean the air filter’s (1) (3)Replace air filter’s (1) (3)Check for fuel and oil leakage X Clean cooling flanges (1) (3)Check cooling air inlet X Replace fu...

24 TROUBLE SHOOTING PROBLEM POSSIBLE CAUSES ENGINE WILL NOT START. Blade switch on.Drive levers not in the neutral slots.Operator not in seat.Park brake disengaged.Dead battery.Fuel valve closed or in the wrong position.No fuel.Spark plugs defective.Spark plug wires off. MACHINE WILL NOT MOVE OR MOV...

25 WIRING DIAGRAMS CONSOLE HARNESS Frame Harness Engine Clutch Left Motion Control Hour Meter Blade Switch Seat Starter Switch Right Motion Control P/N 104414

27 FRAME HARNESS WIRING DIAGRAMS Clutch Engine Pigtail Ground to Engine Starter Solenoid Park Brake Console Harness Brake Relay Start Relay Run Relay P/N 104964