Weil-McLain UO-3 CV - Manual

Table of Contents:

• Page 2 – Potential for Fire, Smoke and Asphyxiation Hazards; To the Homeowner or Equipment Owner:; Oil Burner Manual
• Page 3 – Table of Contents
• Page 4 – Feature; Hazard Defi nitions; WARNING; carbon monoxide poisoning, soot or explosion.; NOTICE; CAUTION
• Page 5 – Do NOT Alter the Original; Tampering with or altering the burner design; Table 1 – Burner Specif cations; Impaired Burner Perfor-; Do NOT operate the burner beyond specif ca-; Thank you for purchasing a Beckett burner; Your Beckett burner will provide years of effi cient op-; mediately contact your quali f ed service agency; – Check the room in which your burner/appli-; Weekly; General Information
• Page 6 – General Specifi cations; Please read and understand the manual supplied with; Professional Service
• Page 7 – tion Hazard; INSULATED STAINLESS STEEL CHIMNEY LINERS; Inspect Chimney or Direct Vent System; Figure 2 – Chimney Design - Above the Roof; Correct; Inspect/Prepare Installation Site
• Page 8 – Failure to provide adequate air supply could; Failure to comply could result in impaired com-; Failure to comply could result in damage to the; confi ned space should have two (2) permanent
• Page 9 – Burner head type; Prepare the Burner; The AFG Low Firing Rate Baffl e (LFRB) reduces; Incorrect nozzles and fl ow rates; and potential fi re or asphyxiation hazards.
• Page 10 – Mount burner on appliance; Recommended nozzle spray angles
• Page 11 – Check/Adjust ‘Z’ Dimension for ‘F’ Heads; Burner Dimensions; Incorrect Adjustments could cause combus-; Adjust the ‘Z’ dimen-
• Page 12 – able for initial adjusting plate settings for V1; V1 heads (see Table below and Figure above for dimensions)
• Page 13 – Figure 7. – Mounting Burner in Appliance; Figure 8. – Inside Tank Gravity Feed System; To further protect the fuel supply sys-; Damage to the pump could cause impaired; Do Not Use Tef on Tape; Oil Leak and Fire Hazard; Install the oil tank following applicable stan-; to determine the proper fuel line size, refer; Fuel Line Valves and Filter; Install two high quality, oil duty rated, fusible; Failure to comply could cause Immediate pump; Do Not Install By-pass Plug
• Page 14 – Fuel supply below the level of the burner –; Always use f are f ttings.; not exceed 3 psig; Do NOT install valves in the return line.; Damage to the fi lter or pump seals could cause; If the residence is unattended in severely cold
• Page 15 – All heating appliances must have
• Page 16 – Typical Burner Sequence of Operation for GeniSys 7505 Control.; Burner Controls
• Page 17 – Table 2 - Reset Button Operation; Reset Button Operation; Table
• Page 18 – Control System Features; Figure 10. – Typical Burner Wiring
• Page 19 – Note that i; Start up burner/set combustion; Some Thermostats Are Polar-; could cause erratic cycling of the burner control.; Wire burner; Failure to prime the pump properly could result; Hot Gas Puff-Back and; Cad Cell Resistance Indicator; Resetting From Restricted or Hard Lockout
• Page 20 – Check Safety Features; Failure to follow these instructions; Explosion and Fire Hazard; Set combustion with instruments
• Page 21 – Perform regular maintenance; Tampering with or making incorrect; Annual Professional Ser-; IF THE BURNER IS SHUT DOWN
• Page 22 – Figure 12. Blower wheel assembly; Replace the blower wheel:
• Page 24 – * Contact your Beckett Representative for part num-; For best performance specify genuine; Beckett; replacement parts
• Page 25 – Limited; WARRANTY; For Residential, Commercial and Specialty Burners; BECKETT; CORPORATION