Weil-McLain Radiant Heater - Manual
Weil-McLain Radiant Heater – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 2 – AlumiPex Radiant Tubing; Hazard Definitions
- Page 3 – Above Floor Installation Guide; TYPICAL SEQUENCE; ABOVE FLOOR INSTALLATION
- Page 4 – A. Tube Layouts for Radiant Heating; Radiant Floor Heatng; Figure 1 - Heat flow from tube through slab
- Page 5 – Figure 2 - Typical tube routing for an above floor installation; Constant Spacing
- Page 6 – UT; BT; TUBE LAYOUT DRAWING -; Figure 6 - Typical tube layout drawing
- Page 7 – B. Obtain Tube Layout Drawing; tube routing; Note Tube Routing
- Page 8 – floor plan design has not been changed.; C. Meet with General Contractor
- Page 9 – Additional Materials; AlumiPex Heat Emission Plates
- Page 10 – Obtain Special Equipment; Tubing Uncoiler; Assists in tube installation.; AlumiPex Tube Cutter; With a scale range of 150 psig.
- Page 11 – G. Mark Floor Plan and Tube Layout on Subfloor; Subfloor must be installed.; Water if no freeze concern.
- Page 12 – Attach the manifold to a plywood panel.
- Page 13 – MANIFOLD MOUNTING; AlumiPex Manifold, Typical; Min; SUPPLY
- Page 14 – Install the Tubing; See Figure 11 for typical details.; Figure 9 - Tubing penetration hole, typical; Subfloor
- Page 15 – Figure 10 - Typical sleeper layout and installation; SLEEPER LAYOUT - ABOVE FLOOR; SLEEPERS; SPACERS; TUBING PATH
- Page 16 – Figure 11 - Typical above floor installation
- Page 17 – Pressure Test the Finished Tubing Installation; Observe the pressure on the gauge.
- Page 18 – K. Pressurize Tubing for Observation; Review traffic recommendations.; Make a record of your installation; Connect System Piping & Heating System Components; Don’t solder within 18 inches of tubing.
- Page 19 – O. Inspection, Repair and Troubleshooting; Repair of kinked or crushed tubing:; N. Inspect Tubing Before Finished Flooring Installation; Repair any damage you find.
Part No. 650-000-221/0298
Above Floor
Installation Guide
AlumiPex
®
Radiant Tubing
These Instructions must be used only by a qualified installer/service
technician. Read these instructions completely before beginning. Failure to
follow these instructions can cause severe personal injury, death or substantial
property damage.
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
AlumiPex Radiant Tubing Part Number 650-000-221/0298 2 Hazard Definitions Indicates presence of hazards that will or cancause minor personal injury or propertydamage. Indicates special instructions on installation,operation or maintenance that are importantbut not related to personal injury or prope...
Above Floor Installation Guide Part Number 650-000-221/0298 3 Tube Layouts for Radiant Heating Obtain Tube Layout Drawing Meet with General Contractor Obtain Materials Obtain Special Equipment Pre-Installation Check List Mark Tube Layout on Subfloor Mount Manifold(s) Install the Tubing Before Leavin...
AlumiPex Radiant Tubing Part Number 650-000-221/0298 4 A. Tube Layouts for Radiant Heating 1. Radiant Floor Heatng a. Hot water flowing in the radiant tubing under thefinished flooring heats the flooring and the heatemission plates. The heat emission plates helpspread the heat evenly across the floo...
