Weed Eater G26LRV - Manual - manualsarea.com

Page 2 - SAFETY RULES

2 SAFETY RULES DANGER: THIS CUTTING MACHINE IS CA PA BLE OF AMPUTATING HANDS AND FEET AND THROWING OBJECTS. FAILURE TO OBSERVE THE FOL LOW ING SAFETY INSTRUCTIONS COULD RESULT IN SERIOUS INJURY OR DEATH. I. GENERAL OPERATION • Read, understand, and follow all instructions on the machine and in the m...

Page 3 - TABLE OF CONTENTS

3 CONGRATULATIONS on your purchase of a new Grass Catcher. It has been designed, en gi neered and manu fac tured to give you the best pos sible de penda bil ity and per form ance.Should you experience any prob lems you can not easily remedy, please contact your nearest au tho rized service center/ d...

Page 4 - KNOW YOUR GRASS CATCHER; UNPACKING INSTRUCTIONS; PARTS IDENTIFICATION

4 NOTE : When right hand (R.H.) and left hand (L.H.) are mentioned in this manual, it means when you are seated on the riding mower, in the operator's position. KNOW YOUR GRASS CATCHER READ THIS OWNER'S MANUAL AND SAFETY RULES BEFORE ASSEMBLING OR OPERATING YOUR GRASS CATCH ER. Compare the illustrat...

Page 5 - ASSEMBLY

5 PULL OUT ON STOP BRACKET TO REMOVE SUPPORT ASSEMBLY TO REMOVE THE SUPPORT ASSEMBLY (See Fig. 2B) 1. Pull outward on the stop bracket enough to allow support assembly to be lifted up and away from drawbar. SHOULDER BOLTS SUPPORT ASSEMBLY REAR MOUNTING BRACKET (See Fig. 2A and 2B) NOTE: Your new dra...

Page 6 - MOUNTING COVER ASSEMBLY TO

6 CONTAINER MOUNTING (See Fig. 4) 1. Install one container to left side first. Install other container to right side. NOTE : Left edge of right con tain er should always over lap right edge of left con tain er at center sup port.2. Close cover and lock latch over center support tube. To lock and rel...

Page 7 - INSTALL DEFLECTOR GUARD

7 INSTALL DEFLECTOR GUARD (See Fig. 5) 1. Using the deflector guard as a template, hold deflector guard on the top of the deflector aligning edge with the holes with bottom of writing and angled end with the rear of the deflector as pictured. 2. Mark locations of (4) holes and drill using supplied #...

Page 8 - BLADE

8 UPPER CHUTE (See Fig. 7A and 7B) 1. Lower mower to its lowest cutting position.2. Assemble upper chute by inserting curved end into hole in back of cover. TIP: Holding upper chute as shown and twisting while ins- talling in cover will help keep the rubber seal in place. NOTE : Handle carefully so ...

Page 9 - LEVEL MOWER DECK

9 COUNTERWEIGHT (See Fig. 9) 1. Lower mower to lowest position to allow access to front axle. 2. Turn steering wheel all the way to the right, for access to left side of axle 3. With extension and socket, insert bolt, lock washer, and washer through hole in axle. NOTE : Insert hardware from rear of ...

Page 10 - TIPS FOR IMPROVED BAGGING OPE RA TION:; OPERATION

10 TIPS FOR IMPROVED BAGGING OPE RA TION: Follow the mower operation instructions in your riding mower owner's manual.When operating your grass catcher on a lawn where grass and leaf bagging equipment has not been used, you are picking up thatch and debris that has accumulated for long periods of ti...

Page 11 - GENERAL RECOMMENDATIONS; BLADE CARE; STORAGE; CUSTOMER RESPONSIBILITIES

11 GENERAL RECOMMENDATIONS Always observe safety rules when performing any main- te nance.• Before each use check for loose fasteners.• Clean unit thoroughly after each use. BLADE CARE For best results, mower blade must be kept sharp. Re place bent or damaged blade.• See BLADE CARE instructions in y...

Page 12 - REPAIR PARTS

12 29 532 17 01-65 Bolt, Shoulder 5/16-18 31 532 17 40-83 Plug, Tubing End 32 532 17 97-46 Bagger, Frame 33 532 19 27-86 Pin, Hinge 34 532 12 75-34 Gasket, Cover 35 532 42 91-13 Container 38 532 13 08-95 Latch Handle, Cover 39 532 15 50-42 Strip, Reinforcement 40 532 42 85-80 Blade 41 532 43 39-68 D...

Weed Eater G26LRV - Manual

Table of Contents:

Summary

Other Weed Eater Models