Wayne WLS100 - Manual

Wayne WLS100 – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.

Page 2 – CONNECTION TO WATER SOURCE; Electrical Connections; Installation
Page 3 – Maintenance; DRAINING FOR WINTER; Operation; PRIMING THE PUMP
Page 4 – Troubleshooting Chart; WIRING CHART - RECOMMENDED WIRE AND FUSE SIZES
Page 5 – Part Number for Models:
Page 6 – Operating Instructions and Parts Manual; Limited Warranty; You; MUST; send a; copy; for return authorization and instructions.; DO NOT MAIL THIS FORM TO WAYNE.; Use this form only to maintain your records.; ATTACH YOUR RECEIPT HERE
Page 7 – PROPOSITION 65 DE CALIFORNIE; Instructions d’Utilisation et Manuel de Pièces de Rechange; INSTALLATION DE LA TUYAUTERIE; MÉMENTO : Gardez votre preuve datée d‘achat à fin de la garantie !
Page 8 – BRANCHEMENT À LA SOURCE D’EAU
Page 9 – Entretien; PURGER POUR L’HIVER; Fonctionnement; AMORÇAGE DE LA POMPE; Vis de mise à la terre
Page 10 – Guide De Dépannage; TABLEAU D’INSTALLATION DE FILS - TAILLES DE FILS ET FUSIBLES
Page 11 – S’il vous plaît fournir l’information suivante:; No
Page 12 – Garantie Limitée; DEVEZ
Page 13 – PROPOSICIÓN 65 DE CALIFORNIA; Instalación; INSTALACION DE LAS TUBERIAS; Adjúntela a este manual o archívela en lugar seguro.
Page 14 – CONEXION A LA FUENTE DE AGUA
Page 15 – Mantenimiento; DURANTE EL INVIERNO; Conecciones Eléctricas; CABLES DE CONEXIÓN; Funcionamiento; PARA CEBAR LA BOMBA
Page 16 – Manual de Instrucciones y Lista de Repuestos; Diagnóstico de Averías; TABLA DE ALAMBRADO - ALAMBRES Y FUSIBLES RECOMENDADOS
Page 17 – Sírvase suministrarnos la siguiente información:; Descripción
Page 18 – Notas
Page 20 – Garantía Limitada; DEBE; enviarnos una; copia; Use este documento sólo para mantener sus records.; ANEXE SU RECIBO AQUI

Loading the manual

Lawn Sprinkler
Pump

Please read and save these instructions. Read carefully before attempting to assemble, install, operate or
maintain the product described. Protect yourself and others by observing all safety information. Failure to
comply with instructions could result in personal injury and/or property damage! Retain instructions for
future reference.

Description

This pump is a high capacity, self-
priming centrifugal pump suitable for
lawn sprinkling or other applications
where large quantities of water are
required. Flammable liquids such as
gasoline, chemicals or corrosive liquids
should never be used with this pump.

Safety Guidelines

This manual contains information that
is very important to know and
understand. This information is
provided for SAFETY and to
PREVENT EQUIPMENT PROBLEMS. To
help recognize this information,
observe the following symbols.

Danger

indicates

an imminently

hazardous situation which, if not avoided,
will result in death or serious injury.

Warning

indicates

a potentially

hazardous situation which, if not avoided,
could result in death or serious injury.

Caution indicates a

potentially hazardous

situation which, if not avoided, may result
in minor or moderate injury.

Notice

indicates

important

information, that if not followed, may
cause damage to equipment.

General Safety
Information

CALIFORNIA PROPOSITION 65

This product or its

power cord may

contain chemicals, including lead, known
to the State of California to cause cancer
and birth defects or other reproductive
harm. Wash hands after handling.

GENERAL SAFETY INFORMATION

1. Read these rules and

instructions carefully. Failure
to follow these instuctions
could cause serious bodily
injury and/or property damage.

Operating Instructions and Parts Manual

WLS75, WLS100

WLS150, WLS200

This pump is non-

submersible.

Pump

only clear water. Do not pump
flammable or explosive fluids
such as gasoline, fuel oil,
kerosene, etc. Do not use in a flammable
and/or explosive atmosphere. Personal
injury and/or property damage could result.

This pump is not

designed to handle

salt water, brine, laundry discharge or
any other application which may
contain caustic chemicals and/or foreign
materials. Pump damage could occur if
used in these applications and will void
warranty.

All wiring must be
performed by a qualified
electrician. The pump must
be installed in compliance with all local
and national codes.

2. Connect this product to a grounded

circuit equipped with a ground fault
interruptor device.

3. Before installing this product, have

the electrical circuit checked by an
electrician to ensure proper
grounding.

4. BE CERTAIN the pump

power source is
disconnected before
installing or servicing
pump.

5. Check motor voltage setting on

motor end plate and make sure the
line voltage of the electrical current
supply is correct.

6. Be sure the water source and piping

is clear of sand, dirt and scale.
Debris will clog pump and void
warranty.

7. Failure to protect pump and piping

from freezing could cause severe
damage and will void the warranty.

320201-001 4/09

8. Do not run pump dry. Follow

priming instructions.

Installation

Protect pump from the elements by
installing in a basement, garage, tool
shed or pump house. Install the pump
so the center line of the pump is as close
as possible to the water level. Keep
installation area clear to provide access
for service and maintenance. Protect the
pump against flooding and excess
moisture.

Make sure the pump has adequate
ventilation. The surrounding
temperature should not exceed 100°F
(38°C) or nuisance tripping of the motor
may occur.

PUMP PIPING INSTALLATION

Use new pipe for best results.
Galvanized or plastic pipe can be used.
When using galvanized pipe, provide
independent supports for both suction
and discharge piping near the pump to
avoid strain on the pump. Minimize use
of elbows and fittings to reduce friction
loss. Refer to the friction loss chart for
specific information.

Increase diameter of suction or discharge
piping if length is over 50 feet.

SUCTION PIPING

Install foot valve

or strainer screen

over intake of suction piping.

Never use pipe smaller than 2” in
diameter for suction piping.

The suction

pipe must be kept free of air leaks. For
horizontal runs, lay pipe from the water
source so the upward slope is at least 1/2”
per foot. This eliminates trapped air. The
threaded inlet of the pump is 2” NPT.

Do not install suc-

tion piping near

swimming areas.

MANUAL

For parts, product & service information

visit

www.waynepumps.com

REMINDER: Keep your dated proof of purchase for warranty purposes!

Attach it to this manual or file it for safekeeping.

"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.

Summary

Page 2 - CONNECTION TO WATER SOURCE; Electrical Connections; Installation

2 Operating Instructions and Parts Manual DISCHARGE PIPING Install a 1-1/2” pipe tee in the pump discharge to allow easy priming. Plug the end of the tee opposite the pump to allow the branch piping to go to the spray nozzles (See Figure 1). Remove the pipe plug to fill the pump with water for primi...

Page 3 - Maintenance; DRAINING FOR WINTER; Operation; PRIMING THE PUMP

If the pump does not operate after repeated attempts, check the following: 1. Vertical distance of pump to water level must not be over 25 feet. 2. Suction piping must be air tight. 3. Be sure valve(s) are open if used in discharge or suction piping. Never run the pump with a closed or clogged disch...

Page 4 - Troubleshooting Chart; WIRING CHART - RECOMMENDED WIRE AND FUSE SIZES

Operating Instructions and Parts Manual 4 1-1/4 2.6 3.9 5.5 9.4 14.1 1-1/2 1.2 1.9 2.6 4.4 6.7 9.4 15.9 2 0.6 0.8 1.3 2.0 2.8 4.7 7.1 10.0 2-1/2 0.6 0.8 1.2 1.3 3.0 4.2 * Multiply by 1.8 for steel pipe psi Friction Loss in 100 Feet of Plastic Pipe* Pipe (Gallons per Hour) Size 1200 1500 1800 2400 30...