Wayne Dalton 3014 - Manual
Wayne Dalton 3014 – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 2 – Table of Contents; IMPORTANT SAFETY INSTRUCTIONS FOR; WARNING
- Page 3 – Step 1: Photoelectric Safety Sensor Bracket Installation
- Page 4 – DoorMasterTM; Step 2: Photoelectric Safety Sensor Wiring Installation For:
- Page 5 – Torsion; driveTM
- Page 6 – Step 4: Photoelectric Obstruction Sensing Test
- Page 7 – IMPORTANT SAFETY INSTRUCTIONS
Wayne-Dalton Corp.
P.O. Box 67 Mt. Hope, OH 44660
(888) 827-3667
www.wayne-dalton.com
Opener Models:
Torsion
i
drive™ models: 3651-372, 3750-372.
Quantum™/Classicdrive™ models: 3012, 3014, 3016, 3018, 3212, 3213, 3214, 3312, 3313, 3314, 3316, 3412, 3414, 3512, 3514.
DoorMaster™ models: BDOR-2000 & BIRW-2000
i
drive™ models: 3660-372, 3661-372, 3662-372, 3760-372, 3751-372.
Photoelectric Safety Sensors
Installation Instructions
and Owner’s Manual
© Copyright 2003 Wayne-Dalton Corp.
New 9/4/2003
Important Notice!
DOOR OPENER WILL NOT OPERATE PROPERLY UNTIL PHOTOELECTRIC
SENSORS ARE INSTALLED AND PROPERLY ADJUSTED! DO NOT OPERATE
DOOR OPENER UNTIL IT IS FULLY INSTALLED, ADJUSTED AND YOU ARE
INSTRUCTED TO DO SO!
Photoelectric Sensors
(1) Sender w/Wire: 260600
(1) Receiver w/Wire: 260597
Photoelectric Sensors Hardware: 297218
(2) 5/16 x 1-1/2” Lag Screws
(2) 1” Flat Head Nails
(2) 1/4-20 x 1/2” Carriage Bolts, Washers & Nuts
(2) Wall Mounting Brackets
(2) “U” Brackets
(1) Power Cord Clip (adhesive back)
(1) Jumper
Part No: 306736
WIRES ARE
PRE-ATTACHED
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
Table of Contents Important Safety Instructions For Installation And Use 2. Bracket Installation 3. Wiring Installation “Quantum™/Classicdrive™” 4. Wiring Installation “DoorMaster™” 4. Wiring Installation “ i drive™” 5. Wiring Installation “Torsion idrive™” 5. Photoelectric Safety Sensor Alignment 6...
WARNING DISCONNECT ALL POWER TO GARAGE DOOR OPENER BEFORE SERVICING ORINSTALLING ACCESSORIES OR PHOTOELECTRICSAFETY SENSORS. FOR ALL OPENERS, UNPLUG 120 VA C P O W E R C O R D F R O M R E C E P TA C L E . F O RDOORMASTER, ALSO UNPLUG TELEPHONE CORD TYPECOMMUNICATIONS CABLE. Select a mounting positio...
NOTE: If wires must be lengthened or spliced into prewired installation, use wire nuts or a suitableconnector. Pay attention to polarity. DoorMaster™ 4 Quantum™/Classicdrive™ FIG. 2 Wire Routing FIG. 1 Wire Routing Quantum™/Classicdrive™ models: 3012, 3014,3016, 3018, 3212, 3213, 3214, 3312, 3313, 3...
