Page 3 - Description of SMIP
www.vxitech.com SM7100 Preface 3 T ABLE OF C ONTENTS I NDTRODUCTION T ABLE OF C ONTENTS ................................................................................................................................................ 3 Certification ......................................................
Page 5 - Microwave Matrix; EMC; FCC Part 15 Subpart B Class A
www.vxitech.com SM7100 Preface 5 D E C L A R A T I O N O F C O N F O R M I T Y Declaration of Conformity According to ISO/IEC Guide 22 and EN 45014 M ANUFACTURER ’ S N AME VXI Technology, Inc. M ANUFACTURER ’ S A DDRESS 2031 Main Street Irvine, California 92614-6509 P RODUCT N AME Microwave Matrix M...
Page 6 - Service should only be performed by qualified personnel.; ERMS AND; WARNING; These symbols may appear on the product:; ATTENTION - Important safety instructions; ARNINGS; Use Proper Power Cord; To avoid hazard, only use the power cord specified for this product.; Use Proper Power Source
VXI Technology, Inc. 6 SM7100 Preface G ENERAL S AFETY I NSTRUCTIONS Review the following safety precautions to avoid bodily injury and/or damage to the product. These precautions must be observed during all phases of operation or service of this product. Failure to comply with these precautions, or...
Page 7 - Avoid Electric Shock; Ground the Product; To avoid injury, electric shock or fire hazard:; Improper Use
www.vxitech.com SM7100 Preface 7 W ARNINGS (C ONT .) Avoid Electric Shock To avoid electric shock or fire hazard, do not operate this product with the covers removed. Do not connect or disconnect any cable, probes, test leads, etc. while they are connected to a voltage source. Remove all power and u...
Page 8 - Technical Support; Visit
VXI Technology, Inc. 8 SM7100 Preface S UPPORT R ESOURCES Support resources for this product are available on the Internet and at VXI Technology customer support centers. VXI Technology World Headquarters VXI Technology, Inc. 2031 Main Street Irvine, CA 92614-6509 Phone: (949) 955-1894 Fax: (949) 95...
Page 9 - ECTION; NTRODUCTION; VERVIEW; The SM7100 Microwave Matrix is a member of the VXI Technology SMIP; ROGRAMMING; The SMIP
www.vxitech.com SM7100 Introduction 9 S ECTION 1 I NTRODUCTION O VERVIEW The SM7100 Microwave Matrix is a member of the VXI Technology SMIP II ™ ( Switch Modularity Interface Platform ) family. It offers a modular design allowing custom switching configurations in a single chassis. The SM7100 is a d...
Page 10 - PECIFICATIONS; RF; SMA
VXI Technology, Inc. 10 SM7100 Introduction Programmable Timing Delays A delay can be programmed between relay closures to allow for settling times of other system resources. When used with triggers, a controlled synchronous switching system can easily be configured. Safety Interrupt This is a progr...
Page 11 - SM7100 Preparation for Use; REPARATION FOR; II
www.vxitech.com SM7100 Preparation for Use 11 S ECTION 2 P REPARATION FOR U SE I NTRODUCTION When the SMIP is unpacked from its shipping carton, the contents should include the following items: (1) SMIP VXIbus module (1) SM7100 Microwave Matrix User’s Manual (this manual) All components should be im...
Page 12 - C D; BACK
VXI Technology, Inc. 12 SM7100 Preparation for Use S ETTING THE L OGICAL A DDRESS The logical address of the SMIP II is set by two rotary switches located on the top edge of the interface card, near the backplane connectors. Each switch is labeled with positions 0 through F. The switch closer to the...
Page 13 - Example 2; LA; FF; ELECTING THE
www.vxitech.com SM7100 Preparation for Use 13 Example 2 LA (decimal) Divide by 16 MSB LSB 200 200 / 16 = 12 w/ 8 remaining Divide by 16. = 1100 1000 Convert to MSB and LSB. = C 8 Convert to hexadecimal. Set the back switch to C and the front switch to 8. 0 1 2 3 4 5 6 7 8 9 A B C D E F 0 1 2 3 4 5 6...
Page 15 - SM7100 Module Configuration; WITCH; RONT; Programming; NOTE; Although
www.vxitech.com SM7100 Module Configuration 15 S ECTION 3 S WITCH C ONFIGURATION F RONT P ANEL C ONNECTION - SM7000 This section details the SM7100 schematics, relays, and pinouts. See Section 4, Programming , for information on relay addressing. NOTE Although pin numbers between the SM7000 and the ...
Page 16 - HP
VXI Technology, Inc. 16 SM7100 Module Configuration T ABLE 3-1: SM7100 F RONT -P ANEL E XTERNAL D RIVE C ONNECTOR P IN A SSIGNMENTS – J17 S IGNAL R ELAY N UMBER P IN N UMBER HP E QUIVALENT EXT 1 K49 J17-1 1 EXT 2 K51 J17-2 3 EXT 3 K53 J17-3 5 EXT 4 K55 J17-4 7 EXT 5 K57 J17-5 9 EXT 6 K59 J17-6 11 EX...
Page 19 - Offset
www.vxitech.com SM7100 Module Configuration 19 T ABLE 3-2: SM7100 R ELAY R EGISTER M AP Offset (Hex) 12 10 E C A 8 K68 K67 K66 K65 6 K64 K63 K62 K61 K60 K59 K58 K57 K56 K55 K54 K53 K52 K51 K50 K49 4 K48 K47 K46 K45 K44 K43 K42 K41 K40 K39 K38 K37 K36 K35 K34 K33 2 K32 K31 K30 K29 K28 K27 K26 K25 K24...
Page 21 - EGISTER; reads; and; writes; directly to the switch module registers. This; DDRESSING; then
www.vxitech.com SM7100 Programming 21 S ECTION 4 P ROGRAMMING R EGISTER A CCESS The SMIP II modules are VXIbus register-based devices for high-speed data transfers. Register- based programming is a series of reads and writes directly to the switch module registers. This eliminates the time for comma...
Page 22 - SMIP; OFFSET
VXI Technology, Inc. 22 SM7100 Programming T ABLE 4-1: SMIP II R EGISTER M AP - A16 OFFSET WRITE FUNCTION READ FUNCTION 3E Trace Advance Board Busy 3C Busy Trigger Control Busy Trigger Control 3A Trace RAM Control Trace RAM Control 38 TTL Trigger Polarity Reserved 36 Open Trigger Select Reserved 34 ...
Page 23 - Logical Address Register (0x00) — Write Only
www.vxitech.com SM7100 Programming 23 D ESCRIPTION OF R EGISTERS - A16 The following describes the registers shown in the SMIP II Register Map for A16 address space. ID Register (0x00) — Read Only D11-D0 Manufacturer's ID VXI Technology, Inc., set to F4B 16 D13-D12 Address Space A16/A24 = 00 2 A16/A...
Page 24 - Version Number Register (0x0E) — Read Only; Interrupt Status Register (0x1A) — Read Only; Note
VXI Technology, Inc. 24 SM7100 Programming Offset Register (0x06) — Read and Write D15-D0 A24/A32 Memory Offset The value written to this 16-bit register, times 256, sets the base address of the A24 memory space used by the module. The value written to this 16-bit register, times 65,536, sets the ba...
Page 25 - Interrupt Control Register (0x1C) — Read and Write
www.vxitech.com SM7100 Programming 25 Interrupt Control Register (0x1C) — Read and Write D15 Scan Function done mask bit 0 = enabled 1 = disabled D14 Openbus Active Event true mask bit 0 = enabled 1 = disabled D13-D9 Unused Data written to these bits has no effect D8 Module Busy Complete 0 = enabled...
Page 27 - Trace RAM Control Register (0x3A) — Read and Write
www.vxitech.com SM7100 Programming 27 Open Trigger Select Register (0x36) —Write Only D15-D8 Sets the TTLTRIG line or lines, which are configures as outputs, and will toggle when Relay Open condition occurs in the module. D15 corresponds to TTLTRIG7, D14 to TTLTRIG6, … and D8 to TTLTRIG0. Setting a ...
Page 28 - Reserved Registers — Read and Write
VXI Technology, Inc. 28 SM7100 Programming Busy Trigger Control Register (0x3C) — Read and Write D15-D8 TTLTRIG Select Sets the TTLTRIG Line or Lines, which are configured as outputs, and will toggle at the de-assertion of a Board Busy condition sent by the plug-in modules. D15 corresponds to TTLTRI...
Page 29 - ESCRIPTION OF; ODULE; Control Register - Read and Write; ADDR
www.vxitech.com SM7100 Programming 29 D ESCRIPTION OF SMIP II M ODULE R EGISTERS - A24 / A32 - E XTENDED M EMORY Each module is assigned 1 k (1024) bytes of memory as shown in the SMIP II Configuration/Relay Register Map for A24/A32 address space. The upper 512 bytes of memory space is used for modu...
Page 32 - Delay Register - Read and Write; Status Register - Read Only
VXI Technology, Inc. 32 SM7100 Programming Delay Register - Read and Write ADDR Plug-In LA+0x202 D15-D0 Data Bus 16 Bit This register is used to set the time that the plug-in module will hold the Board Busy signal active. The Board Busy signal is set every time the plug-in receives a Write to a rele...
Page 33 - ELAY; or; RITING TO THE; Relay Register Address,; data; Energize only one coil in a group of six at one time
www.vxitech.com SM7100 Programming 33 D EVICE M EMORY M AP R ELAY R EGISTER O FFSET The Relay Register Offset is located within the A24/32 address space of the module. When you send data to the register, the relay register offset is added to the A24/A32 base address and module base address: Relay Re...
Page 34 - Handle
VXI Technology, Inc. 34 SM7100 Programming P ROGRAMMING With the introduction of VISA, sending a command to a register-based device is as simple as sending a command to a message-based device. Whether the application is graphical or standard, sending commands to the register-based device is just as ...
Page 35 - NDEX
www.vxitech.com SM7100 Index 35 I NDEX A A16 address space.............................................................23 A16 Base Address.............................................................21 A16 Offset Register ..........................................................21 A16 Offset Regist...
