VTech LS6125 - Manual

Quick start guide

Install the telephone base and

charger(s)

Install the telephone base and charger(s) as

shown below.

B a t t e r y i n s t a l l a t i o n a n d

charging

Install the battery as shown below. After

installing the batter y, you might be able

to make and receive short calls. For best

performance, charge the handset battery for

at least 16 hours before use.

NOTES:

Use only the power adapter(s) and

battery(ies) supplied with your VTech

telephone.
For complete feature instructions,

please refer to your user’s manual.

1.

2.

Outgoing announcement

The telephone is preset with a greeting that

answers calls with

“Hello, please leave a

message after the tone.” You can use this

preset announcement, or replace it with

your own.

To record your own announcement:

Press

ANNC

while the telephone is not

in use and the system will announce

“Announcement. Press

PLAY

or press

RECORD

.”

P r e s s

R E C O R D

a n d t h e s y s t e m

announces,

“Record after the tone. Press

STOP

when you are done.”

A f t e r t h e t o n e , s p e a k t o w a r d s t h e

m i c r o p h o n e a t t h e b o t t o m f r o n t o f

the telephone base from about nine

inches away.
Press

/PLAY/STOP

when finished.

The answering system will automatically

play the newly recorded announcement.

Press

/PLAY/STOP

to stop the playback

at anytime.

To play messages:

Press

PLAY/STOP

to play messages and

stop playback.
Press

X /DELETE

while a message is

playing to delete it.
Press

/SKIP

to skip to the next message.

Press

/REPEAT

to repeat the current

message.
Press

VOL

/

to raise or lower playback

volume.

1.

2.

3.

4.
5.

•

•

•
•

•

IMPORTANT!

If your product is not working properly:

Refer to the

Troubleshooting

section of

the user’s manual.

Visit our website at www.vtechphones.

com or call 1 (800) 595-9511. In Canada,

go to www.vtechcanada.com or 1 (800)

267-7377.

•

•

96-006809-010-100

Telephone base

Telephone line cord

Electrical outlet

not controlled

by a wall switch

Telephone base

power adapter

(large)

Telephone

wall jack

DSL filter (not

included) required

if you have DSL

high-speed

Internet service

Charger

Charger

adapter

(small)

Make, answer and end a call

Make a call

Press

/FLASH

or .

Dial the number.

-OR-

Dial the number.
Press

/FLASH

or .

Answer a call

Press

/

FLASH

, or any of the dialing

keys (

0

-

9

,

#

,

*

).

End a call

Press

OFF/CLEAR

or put the handset in

the telephone base or charger.

Activate the answering system

The answering system must be turned on

to answer and record messages. Press

ANS ON/OFF

to turn the answering system

on or off. When the answering system is

turned on, it will announce

“Calls will be

answered,” and the

ANS ON/OFF

light will be

on. When the answering system is turned off,

it will announce

“Calls will not be answered,”

and the

ANS ON/OFF

light will be off.

1.
2.

1.
2.

•

•

1

2

FLASH

CLEAR

SELECT

MENU

CID

VOL

CHARGE

light

3

4

for models LS6125/LS6125-2/

LS6125-3/LS6125-4/LS6125-5/

LS6126-3/LS6126-5

Plug the battery securely

into the plug inside

the handset battery

compartment, matching

the color-coded label.

Place the battery with the

label

THIS SIDE UP

facing

up and the wires inside

the battery compartment.

Align the cover flat

against the battery

compartment, then slide

it upwards until it clicks

into place.

Charge the handset by

placing it in the telephone

base or charger. The

CHARGE

light will be

on when the handset is

charging.