VTech CL84100 - Manual

Quick reference guide - handset CHARGE indicator On when the handset is charging in the telephone base or charger. q CID/-VOLUME Press q CID to show caller ID history. Press to scroll down while in menus. While entering names or numbers, press to move the cursor to the left.Press to decrease the lis...

Quick reference guide - handset Getting started p DIR/VOLUME+ Press p DIR to show directory entries. Press to scroll up while in menus. While entering names or numbers, press to move the cursor to the right. Press to increase the listening volume when on a call. OFF/CLEAR OFF/CLEAR During a call, pr...

Quick reference guide - handset Getting started Main menu The > symbol highlights a menu item. >Play messages Answering sys Main menu Play messagesAnswering sysDirectoryCall log RingersSettingsWebsite Using menus Press MENU/ SELECT to show the first menu item, Play messages . Press q CID or p ...

4 See pages 6-7for easy instructions. You must install and charge the battery before using the telephone. STOP! Installation Your product may be shipped with a protective sticker covering the handset or telephone base display - remove it before use.For customer service or product information, visit ...

IMPORTANT INFORMATION 1. Use only the power adapter(s) supplied with this product. To order a replacement power adapter, visit our website at www.telephones.att.com or call 1 (800) 222-3111 . In Canada, dial 1 (866) 288-4268 . 2. The power adapters are intended to be correctly oriented in a vertical...

6 Battery installation and charging Install the battery as shown on page 7. Once you have installed the battery, the screen indicates the battery status (see table below). If necessary, place the handset in the telephone base or charger to charge the battery. For best performance, keep the handset i...

Battery installation and charging Getting started 7 Step 1 Plug the battery connector securely into the socket inside the handset battery compartment, matching the color-coded label. Insert the supplied battery with the label THIS SIDE UP facing up as indicated. Step 2 Align the cover flat against t...

Adding and registering handsets Before using a new CL80100 handset, you must register it with the AT&T CL81100/CL81200/CL81300/CL82100/CL82200/CL82250/CL82300/CL82350/CL82400/CL82450/CL82500/CL82550/CL82600/CL84100/CL84200/CL84250/CL84300 telephone system (purchased separately). The telephone sy...

Adding the handset to your telephone base Adding and registering handsets To register a handset to your telephone base (for AT&T CL84100/CL84200/CL84250/CL84300 model) 1. Make sure the handset is out of the charger and alternately shows 1.Press HS LOC on base 4sec and 2.Then press # on handset b...

Deregistering a handset You may need to deregister your handsets if: You have 12 registered handsets and need to replace a handset. -OR- You wish to change the designated handset number of your registered handsets. You must first deregister ALL the handsets, and then register each handset you wish t...

Adding the handset to your telephone base 12 Deregistering a handset To deregister all handsets (for AT&T CL84100/CL84200/CL84250/CL84300 model) 1. Press and hold LOCATOR on the telephone base for about 10 seconds until the base screen shows Registering handset... followed by Deregister all hand...

Troubleshooting If you have difficulty with your phone, please try the suggestions below. For Customer Service, visit our website at www.telephones.att.com or call 1 (800) 222-3111 . In Canada, dial 1 (866) 288-4268 . The handset registration is unsuccessful. Follow the handset registration instruct...

Troubleshooting Appendix 14 If the previous suggestions do not work, disconnect the telephone base from the telephone jack and connect the jack to a different phone. If there is no dial tone on that phone either, the problem is in your wiring or local service. Contact your telephone service provider...

Troubleshooting Appendix Out of range OR No pwr at base appears on my cordless handset. Ensure you plug the telephone base in properly and the power is on.Place the cordless handset in the telephone base for one minute to allow the cordless handset and base to synchronize.Move the cordless handset c...

I get noise, static, or weak signals even when I’m near the telephone base. If you subscribe to high-speed Internet service (DSL - digital subscriber line) through your telephone lines, you must install a DSL filter between the telephone base and the telephone wall jack. The filter prevents noise an...

My cordless handset does not ring when I receive a call. Make sure that the ringer is not off. Refer to Ringer volume in the user’s manual provided with your CL81100/CL81200/CL81300/CL82100/CL82200/CL82250/CL82300/CL82350/CL82400/CL82450/CL82500/CL82550/CL82600/CL84100/CL84200/CL84250/CL84300 teleph...

Troubleshooting Appendix My calls cut in and out while I’m using my cordless handset. Other electronic products can cause interference with your cordless phone. Try installing your phone as far away from the following electronic devices as possible: television sets, VCRs, or other cordless telephone...

19 Troubleshooting Appendix System does not receive caller ID when on a call. Make sure you subscribe to caller ID with call waiting features from your telephone service provider. Caller ID features work only if both you and the caller are in areas offering caller ID service, and if both telephone s...

Troubleshooting Appendix The charge light is off or blinking. Make sure you plug the power and line cords in correctly and securely.Unplug the electrical power. Wait for 15 seconds, then plug it back in. Allow up to one minute for the cordless handset and telephone base to reset.Clean the cordless h...

Maintenance Taking care of your telephone Your cordless telephone contains sophisticated electronic parts, so you must treat it with care.Avoid rough treatment. Place the handset down gently. Save the original packing materials to protect your telephone if you ever need to ship it. Avoid water You c...

24 Pacemaker patients Should keep wireless telephones at least six inches from the pacemaker.Should NOT place wireless telephones directly over the pacemaker, such as in a breast pocket, when it is turned ON.Should use the wireless telephone at the ear opposite the pacemaker.WTR’s evaluation did not...

Appendix FCC Part 68 and ACTA This equipment complies with Part 68 of the FCC rules and with technical requirements adopted by the Administrative Council for Terminal Attachments (ACTA). The label on the back or bottom of this equipment contains, among other things, a product identifier in the forma...

Appendix 30 Limited warranty 7. Other limitations This warranty is the complete and exclusive agreement between you and the manufacturer of this AT&T branded PRODUCT. It supersedes all other written or oral communications related to this PRODUCT. The manufacturer provides no other warranties for...

Operation Operating time* Talk time (cordless handset) Up to seven hours Talk time (cordless handset speakerphone) Up to five hours Standby Up to seven days * Operating times vary depending on your actual use and the age of the battery. DECT 6.0 digital technology The AT&T DECT 6.0 products offe...