Page 2 - ViewSonic; Compliance Information; CE Conformity for European Countries
ViewSonic WPD-100 i Compliance Information For U.S.A. This device complies with part 15 of FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may c...
Page 3 - ii; FCC Radiation Exposure Statement
ViewSonic WPD-100 ii FCC Radiation Exposure Statement This equipment should be installed and operated with minimum distance 20cm between the radiator & your body.This wireless module device complies with part 15 of FCC Rules. Operation is subject to the following two conditions: (1) this device ...
Page 4 - iii; Declaration of RoHS Compliance; specifically mentioned in the Annex of RoHS Directive.
ViewSonic WPD-100 iii Declaration of RoHS Compliance This product has been designed and manufactured in compliance with Directive 2002/95/ EC of the European Parliament and the Council on restriction of the use of certain hazardous substances in electrical and electronic equipment (RoHS Directive) a...
Page 5 - iv; Copyright Information; Copyright © ViewSonic; Product Registration; Wireless Presentation Dongle; Product disposal at end of product life
ViewSonic WPD-100 iv Copyright Information Copyright © ViewSonic ® Corporation, 2010. All rights reserved. ViewSonic ® , the three birds logo, OnView ® , ViewMatch ™ , and ViewMeter ® are registered trademarks of ViewSonic ® Corporation. Disclaimer: ViewSonic ® Corporation shall not be liable for te...
Page 6 - C A T A L O G
ViewSonic WPD-100 C A T A L O G CHAPTER I: Product Information................................................................................. 1 1-1 Introduction and safety information....................................................................... 1 1-2 Safety Information .....................
Page 7 - WMM function: control the bandwidth required for different
ViewSonic WPD-100 1 CHAPTER I: Product Information 1-1 Introduction and safety information Thank you for purchasing ViewSonic WPD-100! Excepting common wireless standards 802.11b/g, it is also able to access 802.11n wireless networks - data transfer rate is 150Mbps, and that’s three times faster tha...
Page 8 - -2 Safety Information; This is
ViewSonic WPD-100 2 1-2 Safety Information In order to keep the safety of users and your properties, please follow the following safety instructions: 1. This WPD-100 is designed for indoor use only. DO NOT expose it to direct sun light, rain, or snow. 2. DO NOT put WPD-100 at or near hot or humid pl...
Page 9 - -3 System Requirements; performance will be greatly reduced)
ViewSonic WPD-100 3 1-3 System Requirements An empty USB 2.0 port (May not be able work with USB 1.1 port, and performance will be greatly reduced) Windows XP, Vista, or WIN7 operating system CD-ROM drive At least 100MB of available disk space
Page 10 - -4 Package Contents
ViewSonic WPD-100 4 1-4 Package Contents Before you starting to use WPD-100, please check if there’s anything missing in the package, and contact your dealer of purchase to claim for missing items: 1 - WPD-100 (1 pcs) 2 - Protection Cap (1 pcs) 3 - Quick Start Guide (1 pcs) 4 - CD (with Driver/Utili...
Page 12 - CHAPTER II: Driver Installation and Configuration
ViewSonic WPD-100 6 CHAPTER II: Driver Installation and Configuration 2-1 WPD-100 Installation Please follow the following instructions to install WPD-100. 1. Insert the WPD-100 into an empty USB 2.0 port of your computer when computer is switched on. Never use force to insert the WPD-100, if you fe...
Page 14 - -2 Connect to Wireless Access Point; Wireless connection is established, good signal reception.
ViewSonic WPD-100 8 2-2 Connect to Wireless Access Point After the driver is correctly installed, you could use the utility to connect a specific wireless access point you wish to connect. The current status of wireless connection will be displayed by WPD-100 utility icon: Wireless connection is est...
Page 15 - computer desktop and then clicks ‘Launch Config Utility’.; Menu
ViewSonic WPD-100 9 2-2-1 Using WPD-100 Utility Please follow the following instructions to use WPD-100 utility to connect to wireless access point. 1. Right-click the WPD-100 utility icon located at lower-right corner of computer desktop and then clicks ‘Launch Config Utility’. 2. WPD-100 utility w...
Page 16 - know its encryption key.
ViewSonic WPD-100 10 2-2-1-1 Scan for Other Wireless Devices There are two kinds of wireless connection mode: Infrastructure and Ad-Hoc. Infrastructure mode is used by wireless access points, which is able to establish wireless connection for you and other wireless / wired network clients. Ad-Hoc mo...
Page 17 - The SSID (Service Set Identifier) of wireless device. If nothing is; A B
ViewSonic WPD-100 11 Please launch WPD-100 setup utility and it will scan for wireless access points near by: Scan results will be displayed here, please check if the wireless device (access point or another computer) with the SSID you wish to connect is shown here. Scan result includes 6 types of i...
Page 18 - Note: When the access point supports WPS and WPS icon is appeared,
ViewSonic WPD-100 12 ‘n’ for 802.11n , ‘g; for 802.11g , and ‘b’ for 802.11b . WPS icon will appear when the access point supports WPS. If the access point uses encryption, a key icon will appear. Note: When the access point supports WPS and WPS icon is appeared, you will not see the key icon here e...
Page 19 - There are 4 types of technical information:
ViewSonic WPD-100 13 There are 4 types of technical information: General: Displays basic information about this access point, such as SSID, MAC Address, authentication / encryption type, channel etc. WPS: If this access point supports WPS (Wi-Fi Protected Setup), related information will be displaye...
Page 20 - Item Name
ViewSonic WPD-100 14 And here are descriptions of every setup item in setup area: Item Name Description Sorted by >> You can decide how to sort all listed access point by ‘SSID’, ‘Channel’, or ‘Signal’ (signal strength). Show dBm Check this box to show the signal strength of access point, inst...
Page 22 - symbol appears in front of the name of wireless device.
ViewSonic WPD-100 16 4. Please ask the owner of the wireless access point you want to connect, and input the correct key here and then click ‘OK’. If the value you inputted here is wrong, you will not be able to connect to this wireless access point. Authentication type will be selected by the authe...
Page 25 - RTS Threshold
ViewSonic WPD-100 19 Power Save Mode Please select CAM (constantly awake mode, keep wireless radio activity even when not transferring data), or PSM (Power saving mode, switches radio off when not transferring data). It’s recommended to choose ‘PSM’ if you’re using this network card with notebook co...
Page 32 - If you can see ‘Connected’ message, the connection between your
ViewSonic WPD-100 26 8. If you can see ‘Connected’ message, the connection between your computer and wireless access point is successfully established.
Page 33 - -3 Advanced Settings
ViewSonic WPD-100 27 2-3 Advanced Settings This wireless network card provides several advanced settings for experienced wireless users. Here are descriptions of every setup item: Item Name Description Wireless mode Display the wireless operation mode of the network card. Enable Tx Burst Check this ...
Page 34 - -4 View Network Statistics
ViewSonic WPD-100 28 2-4 View Network Statistics This section provides information about network statistics and link status. All connection-related statistics is displayed here. You can click ‘Transmit’ or ‘Receive’ tab, to view the statistics of transmitted or received packets. You can also click ‘...
Page 36 - -6 WPS Configuration
ViewSonic WPD-100 30 2-6 WPS Configuration Wi-Fi Protected Setup (WPS) is the latest wireless network technology which makes wireless network setup become very simple. If you have WPS-enabled wireless access point, and you want to establish a secure connection to it, you don’t have to configure the ...
Page 38 - it happens, you can click ‘PBC’ button few more times to try again.
ViewSonic WPD-100 32 3. Start PBC pairing procedure at access point side (please refer to the instruction given by your access point’s manufacturer), then click ‘PBC’ button in wireless configuration utility to start to establish wireless connection by WPS. Please be patient (This may take a period ...
Page 40 - Enable Pre-Logon Connectivity
ViewSonic WPD-100 34 2-7 SSO Single sign-on (SSO) is a property of access control of multiple, related, but independent software systems. With this property a user logs in once and gains access to all systems without being prompted to log in again at each of them. Here are descriptions of every setu...
Page 41 - Enable Radio Measurements: When you’re
ViewSonic WPD-100 35 2-8 CCX CCX is a wireless feature developed by Cisco used to improve the wireless performance with CCX compatible wireless devices. Here are descriptions of every setup item: Enable CCX 1. Enable Radio Measurements: When you’re connecting to CCX-compatible access point, check th...
Page 43 - Click this button to view on-line help documents.
ViewSonic WPD-100 37 2-11 On-line Help If you need to know the directions of how to use specific function in the utility, please click ‘Help’ button. On-line help documents will be presented in Windows help format. Click this button to view on-line help documents.
Page 44 - -1 Switch to AP Mode and Basic Configuration
ViewSonic WPD-100 38 CHAPTER III: Soft-AP Function Excepting become a wireless client of other wireless access points, this wireless card can act as a wireless service provider also! You can switch this wireless card’s operating mode to ‘AP’ mode to simulate the function of a real wireless access po...
Page 46 - Hide SSID
ViewSonic WPD-100 40 2: SPAIN 3: FRANCE 4: MKK 5: MKKI (TELEC) 6: ISERAL (Channel 3 to 9) 7: ISERAL (Channel 5 to 13) Please note that only change the country code if you are in different country. For example: when operating this product in US, only channels 1~11 can be operated. Selection of other ...
Page 47 - -2 Security Setting
ViewSonic WPD-100 41 3-2 Security Setting This wireless card supports wireless encryption in AP mode, which will encrypt the data being transferred over the air to enhance data security level. It’s recommended to enable data encryption unless you wish to open your computer (and its internet connecti...
Page 48 - Wep Key
ViewSonic WPD-100 42 data will not be encrypted and people with some networking knowledge will be able to read the data you transfer with proper tool. WPA Pre-shared Key Please input the WPA pre-shared key here. Only clients with the same pre-shared key you inputted here will be able to connect to y...
Page 50 - MAC address
ViewSonic WPD-100 44 Reject All: Reject wireless clients with MAC address listed here to be connected to this access point. MAC address Input the MAC address of the wireless client you wish to allow or reject here. No colon (:) or hyphen (-) required. Add Add the MAC address you inputted in ‘MAC add...
Page 51 - -4 Connection Table
ViewSonic WPD-100 45 3-4 Connection Table If you want to see the list of all wireless clients connected to this access point, please select ‘Mac Table’ tab from the utility. Here are descriptions of every field: Item Name Description MAC Address Displays the MAC address of this wireless client. AID ...
Page 54 - -8 Open Diagnostic Testing Mode
ViewSonic WPD-100 48 3-8 Open Diagnostic Testing Mode The function is to check if utility, driver, and network all work fine.
Page 55 - CHAPTER IV: Appendix; Cisco CCX Support
ViewSonic WPD-100 49 CHAPTER IV: Appendix 4-1 Specification Standards: IEEE 802.11b/g Interface: USB 2.0 (USB 1.1 Compatible) Frequency Band: 2.4000 ~ 2.4835GHz (Industrial Scientific Medical Band) Data Rate: 11b: 1/2/5.5/11Mbps 11g: 6/9/12/24/36/48/54Mbps 11n (20MHz): MCS0-7 (up to 72Mbps) 11n (40M...
Page 58 - Customer Support; You will need the product serial number.
ViewSonic WPD-100 52 Customer Support For technical support or product service, see the table below or contact your reseller. NOTE: You will need the product serial number. Country/Region Website T = Telephone F = FAX Email Australia/New Zealand www.viewsonic.com.au AUS= 1800 880 818 NZ= 0800 008 82...
Page 59 - Limited Warranty; to get warranty information.
ViewSonic WPD-100 53 Limited Warranty Please go to the Customer Support table in this guide for the ViewSonic website in your region to get warranty information.
