Vermont Casting RADVTEB - Manual

Table of Contents:

• Page 2 – Radiance Direct Vent Gas Heater; Table of Contents
• Page 3 – In the Commonwealth of Massachusetts:; • All gas fitting and installation of this heater shall only be; Installation & Operating Instructions
• Page 4 – RADVT Models; RADVTC Models; Radiance Direct Vent Stove Dimensions; Proposition 65 Warning:; Fuels used in gas, woodburning; Radiance Direct Vent
• Page 5 – Installation Requirements; Possible stove locations.; Direct Vent System Only; Stardance; Clearance Requirements; Minimum Clearances to Combustible Materials; Locating The Stove
• Page 6 – Parallel installation, minimum back and side clear-; Corner installation, minimum corner clearances and; Minimum wall centerline.; Sidewall Clearance; Direct Vent Only
• Page 7 – Gas Specifications
• Page 8 – Vertical Termination; NOTE: The restrictor; Vertical vent termination window.; Restrictor Plate Adjustment; restrictor plate; Loosen screw to adjust restrictor plate.; Examples for Extended Run/Restrictor Plate Settings; ” (70 mm) from center of screw to top edge of plate
• Page 9 – Vent Termination Clearances; IMPORTANT
• Page 10 – General Venting Information - Termination Location; Canadian Installations
• Page 11 – Termination clearances.; Outside Corner; Termination Clearances; with no side wall; of Caps
• Page 12 – Venting Requirements and Options; Approved Vent System Components; Simpson DuraVent Components; Minimum Horizontal Vent Kit; Selkirk Corporation Vent Components
• Page 13 – Vertical Termination Cap; CFM Vent Components; and all of the other Vertical Termination parts.
• Page 14 – Slide stove back just far enough to access rear leg; Assembly Procedures; Failure to position the parts in accor-; WARNING; Tools Required; Carefully tip stove onto back legs. Leave pallet under
• Page 15 – JUV; Attach the fan rheostat.; Install the Optional Fan; Remove rear shroud.; Fan kit components.; Steps 3 and 4 do not apply to RADVTC series; Attach blower assembly and snapstat.; Attach the control knob to the rheostat shaft.
• Page 16 – Venting System Assembly; For Canadian installations:; Connect the inner starter with the next section of in-; Dry fit the Inner Pipe assembly to the stove for; Attach inner assembly to flue collar.; attach inner assy; install outer adpater; Install the Vent Adapter Pipe; Discard the inner starter pipe
• Page 17 – Simpson DuraVent - install inner adpater pipe.; Install Vent Adapter Pipe; Vent Opening; Combustible Wall; Locate vent opening.; CFM System; leave air space on top side of cut out.; For DuraVent pipe only:
• Page 18 – Zero Clearance Sleeve; Assemble the wall sleeve and firestop.; measure vertical vent; Determine the vertical pipe length.; measure thru wall; Measure the horizontal length.; install pipe thru wall; Install the horizontal pipe and wall plate parts.; install wall terminal; Install the vent terminal.
• Page 19 – Vent Termination Below Grade; If the; snorkel detail; Use extension brackets to mount snorkel against; install snorkel; Snorkel kit installation.; Vent Assembly
• Page 20 – Install firestops and attic insulation shield.; vent thru roof; Roof support and flashing.; Selkirk Direct-Temp Metalbestos Direct; Installation Instructions; Model DT Ceiling Support (CS) Cathedral Ceiling Wall Thimble; Use of Sealant
• Page 21 – Inlet End; Fig. 36 Selkirk Venting Components
• Page 22 – Supporting DIRECT-TEMP: Horizontal Support; Horizontal Installation
• Page 23 – Below grade installation.; As a general rule, the wall thimble is optional in; When installed in Canada, a; The wall thimble accommodates wall thickness-; Horizontal Termination; Vinyl siding standoff and horizontal termination.
• Page 24 – If a vertical rise is necessary on the exterior side; do not back fill; Vertical Installation; Frame openings to the dimensions specified; Typical vertical venting configuration.; If the cathedral ceiling support box assembly is
• Page 25 – Minimum; Fig. 45 Minimum Height Above Roof Requirements; Whenever DIRECT-TEMP penetrates through a; Remove the stove front.; Install Log Set; each piece for damage.; Release the latches to remove the glass frame.
• Page 26 – Install the front left and right logs
• Page 27 – Connect the Gas Supply Line; Gas connection should be made in ac-; CAUTION
• Page 28 – Install ON/OFF Switch; The switch assembly parts are found in the parts bag.; PILOT; attach switch; Attach switch wires to valve.; THIS APPLIANCE SHOULD BE CON-; attach switch assy; Attach switch assembly to rear shroud.; Use only a thermostat rated for 500 - 750 millivolts.; Install the Mesh and Grille; Thermostat; Operation; Install the wall thermostat in the desired location and; Your First Fire
• Page 29 – Pilot Assembly location.; Flame & Temperature Adjustment; Flame adjustment knob for SIT valve.; Pilot flame; SIT Pilot; Correct pilot and burner flame appearance.; RADVT Series; Flame Characteristics
• Page 30 – FOR YOUR SAFETY READ BEFORE LIGHTING; WHAT TO DO IF YOU SMELL GAS; To Turn Off Gas To Heater; Lighting and Operating Instructions; Lighting Instructions; Lighting instructions
• Page 31 – Troubleshooting the Gas Control System (RADVT Series); NOTE; SIT NOVA 820 MILLIVOLT VALVE
• Page 32 – RADVTC Series; comfort valve; Transmitter diagram.; Honeywell; Comfort control valve.
• Page 33 – If an Error Code 3 is observed while performing the; Blower; Comfort Valve wiring diagram.
• Page 34 – Local Path
• Page 35 – above; Auto Path; below
• Page 36 – Conversion Precautions; Fuel Conversion Instructions; attach gas line; Attach the gas line to the right side of the valve.; Conversion Procedure; WARNING: Do not overtighten the; LP Configuration; RADVTC Series Models
• Page 37 – gas conversion; Remove pilot hood.; Gas Conversion; Remove pilot orifice.; Jefferson; Rf pilot Conversion; Remove pilot hood. (Your pilot may have a different; Depress and turn center plunger.; Pilot Orifice Conversion
• Page 38 – Burner Orifice Conversion; Carefully remove ember bed by tilting the right side; RF Pilot conversion; Bottom View; Remove injector orifice from left burner bracket with; Tilt ember bed slightly to correctly place on venturi; All Models; Replace burner making sure venturi on bottom of
• Page 39 – Table 3. Air Shutter Adjustment; Conversion to Natural Gas
• Page 40 – Maintenance; painted surfaces; Remove the Stove Front.
• Page 41 – Gasket Replacement; Determine the correct length of gasket by laying it; Inspect the Vent System Annually; glass gasket detail; Wrap the gasket material around the outside edge of
• Page 42 – BLK; rdv connections diag.; Schematic Diagram; Wiring Diagrams; On/off switch and optional thermostat circuit.
• Page 45 – Fuel Conversion Kits
• Page 46 – Shell Enamel Parts - Radiance Direct Vent
• Page 47 – Optional Accessories; Fan Kits
• Page 51 – PLATED PARTS AND ACCESSORIES:; LIMITED LIFETIME WARRANTY
• Page 52 – CFM Corporation