Verilux VF02 - Manual - manualsarea.com

Page 3 - SAVE THESE INSTRUCTIONS; Important Safety Instructions

3 SAVE THESE INSTRUCTIONS Thank you for purchasing the Original Natural Spectrum ® Floor Lamp. Please read the following safety information before using. To reduce the risk of fire, electrical shock or injury to persons:• Do NOT dismantle. • Do NOT alter power cord. • Turn off/unplug and allow to co...

Page 4 - Avertissements et Précautions

4 Avertissements et Précautions • Pour usage intérieur seulement. • La lampe est un dispositif électrique. NE PAS UTILISER PRÈS DE L’EAU. • Avant de brancher la lampe, vérifier que la tension de la prise murale ne dépasse pas 120 volts. • Ne pas utiliser avec des gradateurs de lumière, des minuterie...

Page 5 - Getting Started

5 Getting Started Main Parts & ControlsA. Ergonomic Handle B. Lamp Head C. High/Off/Low Switch D. Gooseneck E. Shaft F. Ergonomic Height Adjustment Lever G. Lamp Base H. Power Cord I. Ballast J. LED Indicator K. Bulb L. Parabolic Light Diffuser A B C D E F H G I Close-up of Lamp Head Close-up of...

Page 6 - Getting Started — continued; Please Read Instructions Carefully Before Using the EasyFlex

6 Getting Started — continued Please Read Instructions Carefully Before Using the EasyFlex ® . 1. Unpack lamp carefully, removing all packaging material, and confirm you have all parts shown in the diagram. For your convenience, the bulb has been inserted into the socket. 2. Remove all pieces from b...

Page 7 - Assembly Instructions

7 Assembly Instructions 1. Set the lamp base on the floor and insert the lamp shaft over the base support unit until the screw holes line up as shown in Fig. 1. Insert the screw using the tightening tool and turn clockwise to tighten. 2. Hold the upper shaft with one hand and release the ergonomic h...

Page 8 - Assembly Instructions — continued; Be sure all

8 Assembly Instructions — continued 3. Attach the lamp head gooseneck to the shaft until the screw holes line up as shown in Fig. 3. Use care when tucking the wire into the shaft. Form a loop with any excess wire prior to tucking it. Insert the screw using the tightening tool and turn clockwise to t...

Page 9 - Green LED indicator will not illuminate if; WARNING: Do not block vents on the

9 Assembly Instructions — continued 5. Attach the ballast to the power cord. Use care to align the 4-pin plug properly. DO NOT FORCE. The power cord is designed to connect only one way (Fig. 5). 6. Plug the ballast into a standard 120V 50/60Hz outlet and turn the lamp on. The green LED indicator (J)...

Page 10 - Bulb Replacement; Do not grip the bulb by the

10 Bulb Replacement Fig. 7 Correctly Seated Bulb Incorrectly Seated Bulb No Gap Notice Large Gap Fig. 8 B D C A Fig. 9 Removal1. Unplug the lamp from the power source. 2. To access the bulb, remove light diffuser by depressing the tab and lifting it out (Fig. 7). 3. Firmly hold the bulb base (B) and...

Page 11 - Troubleshooting; Before requesting service on your Verilux

11 Troubleshooting Before requesting service on your Verilux ® lamp, please read the following: • Make sure all power connectors, cords and plugs are inserted fully and securely. • Be sure the bulb is securely seated into the socket (see page 9). • Make sure there is power to the wall outlet or try ...

Page 12 - Troubleshooting – continued

12 Troubleshooting – continued Be sure the bulb is securely seated into the socket, repeat the bulb installation process. CAUTION: DISCONNECT LAMP FROM OUTLET PRIOR TO REPEATING THE BULB INSTALLATION PROCESS. MISE EN GARDE : DÉBRANCHER LA LAMPE DE LA PRISE DE COURANT AVANT DE POSER UNE NOUVELLE AMPO...

Page 14 - One Year Limited Warranty

Please visit our website at www.verilux.com or call our Customer Service Department at 1-800-786-6850 Representatives are available Monday — Friday, 9am — 5pm EST 340 Mad River Park, Waitsfield, VT 05673 One Year Limited Warranty ATTENTION! ONCE OPENED, PLEASE DO NOT RETURN THIS PRODUCT TO THE STORE...

Verilux VF02 - Manual

Table of Contents:

Summary

Other Verilux Models