Uniden XS1415/1415+1 - Manual

7 Installing.the.Phone Choosing.the.Best.Location When choosing a location for your new phone, here are some important guidelines you should consider: Note: For maximum range: Keep both the base and handset antennas free of obstruction.When the handset is not in use, place the handset in an upright ...

9 Installing.the.Base.Unit.and.Charging.Cradle.(XS1415+1.only).. ) Connect each AC adapter to the DC.IN.9V jack and to each standard 240V AC wall outlet. Note:.•.. Use.only.the.supplied.PS-S0921YL3.AC.adapter. for.the.base.unit.and.AAD-600S(M).for.the.charging.cradle.(XS1415+1.only)...Do.not.use.any...

Mounting.the.Base.Unit.on.a.Wall Standard.wall.plate.mounting This phone can be mounted on any standard wall plate. ) Plug the AC adapter to the DC.IN.9V jack. 2) Plug the AC adapter into a standard 240V. AC wall outlet. 3) Plug the telephone cord into the TEL.LINE jack. 4) Route the telephone cord ...

2 Direct.wall.mounting If you don’t have a standard wall plate, you can mount your phone directly to the wall. Before doing this, consider the following: Avoid electrical cables, pipes, or other items behind the mounting location that could cause a hazard when inserting screws into the wall.Try to m...

3 Register.Handsets.to.the.Main.Base.before.Using!.(XS1415+1.only) Both handsets will need to be registered to the main base unit before use. Whichever handset you choose to charge in the base unit will automatically register to the base unit. The handset charging in the extra charging cradle MUST a...

4 When.to.Re-register.Handsets.(XS1415+1.only) In some cases, it may be necessary to re-register your handsets. To re-register your handsets, please follow registration steps outlined on page 3. Re-registration is required in the following scenarios:) You’ll need to re-register both handsets (follow...

5 Basic.Setup There are four basic options that you will need to set up: AutoTalk, CIDCW (Caller ID on Call Waiting),Name Tag and Insert 0. CIDCW option can only be set by using Handset . If you try to set by using Handset 2, you will not see these options listed on the LCD screen. (Handset shows in...

20 4) Enter a name according to the instructions below, then press [select/channel] (XS45+) or [select] (XS45). If no name is required, go to step 5. The name can be up to 3 characters.Use [ /tone/ ] and [#/ ] to move the cursor to the desired location. Press [delete/transfer] (XS45+) or [delete/cha...

27 Using.Call.Waiting If you have Call Waiting service, you can receive calls while on the line. If a call comes in while you are on the phone, you will hear a call waiting tone. If you have CIDCW activated, you will see the nameand number of the incoming caller. Australia: Press [talk/flash] key an...

32 Changing.the.Digital.Security.Code To protect you against misbilled calls which might result from your phone being activated by other equipment, the cordless phone provides Random Code digital security which automatically selects one of over 262,000 digital security codes for each handset and the...

33 Maintenance Specifications Operating.temperature -0°C to +50°C (+4°F to +22°F) AC.Adapter For.the.base For.the.charger Part.number PS-S092YL3 AAD-600S(M) Input.Voltage 240V AC 50Hz 240V AC 50Hz Output.Voltage 9V DC 20mA 9V DC 20mA Battery Part.number BT905s Capacity 500mAh, 3.6V Note:.To.avoid.da...

36 Troubleshooting Traveling.Out-of-Range During a call, as you begin to move your handset too far from your base unit, noise increases. If you pass the range limits of the base, your call will terminate within one minute. Common.Issues If your phone is not performing to your expectations, please tr...

37 Symptom Suggestion Can’t make or receive calls. Re-register both handsets (see page 3).Check both ends of telephone cord.Make sure the AC adapter is plugged into the base and wall outlet.Disconnect the AC adapter for a few minutes, then reconnect it.Change the digital security code (see page 32)....

38 Symptom Suggestion The Caller ID does not display. The call was answered before the second ring.The call was placed through a switchboard.Charge the handset.Your Caller ID service may not be active; contact your local telephone service provider. •••• A handset is not working. Make sure the batter...

40 Index A AC adapter information.................. 33 B Basic setup .................................... 5 Battery pack Information ................................. 33 Installing ...................................... 8 Preparing and charging ........... 8, 9 Replacement and handling ........ 35 C...