Page 3 - Important Safety Instructions
11. To reduce the risk of electric shock. do not Important Safety Instructions When using your telephone equipment, these basic safety precautions should always be followed to reduce the risk of fire, electrical shock, and injury topersons: 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. Read and understand all inst...
Page 4 - Battery Safety Precautions; Introduction; Features
Battery Safety Precautions Introduction Caution: To reduce the risk of fire or injury to persons by the battery read and follow these instructions: Congratulations on your purchase of the Uniden XC610 Series/XC710 Cordless Telephone. This phone is designed to exacting standards whichprovide reliabil...
Page 5 - Important Electrical Considerations; Range
Included with the XC610 Series/XC710 If any of these items are missing or damaged, contact the place of purchased. Handset Base Unit Rechargeable Battery or Telephone Cord Telephone Cord AC Adapter for Australia for New Zealand (AAD-600S) Important Electrical Considerations Unplug all electrical app...
Page 6 - Installation; Selecting a Location; You should charge your new phone for; Connecting the Telephone Cords
Radio Interference Radio interference may occasionally cause buzzing and humming in your cordless Handset, or clicking noises in the Base Unit. This interference is caused by external sources such as TV, refrigerator, vacuumcleaner, fluorescent lighting, or electrical storm. Yourunit is NOT DEFECTIV...
Page 7 - Applying Power to the Base Unit; Desk or Tabletop Installation; TEL LINE
Applying Power to the Base Unit All the XC610 Series/XC710 Cordless Telephone requires an AC outlet, and the included AC adapter. To relieve strain on the DC plug when the phone is placed on a desk or table, connect the adapter asshown below. Important Wrap the power cord around the convenient notch...
Page 8 - Wall Installation
Wall Installation Before mounting your phone, consider the following: l Select a location away from electricalcables, pipes, or other items behind the mounting location that could cause a hazard when inserting screws into the wall. l Make sure the wall material is capable of supporting the weight of...
Page 9 - Setting the Handset Retainer
7. Plug the other end of the telephone line cord into the wall jack. 8. Plug the AC Adapter into a standard 2 3 0 / 240 AC wall outlet. Setting the Handset Retainer The handset retainer holds the Handset in place ifyour phone is mounted on a wall. The steps below describe how to remove and replace t...
Page 10 - Setting Up Your Phone; Extending the Antenna; Cleaning the Battery Contacts; not
Setting Up Your Phone Extending the Antenna Before using your phone, be sure to raise its antenna to the vertical position. Installing the Handset Battery Pack 1. 2. 3. Press in on the Battery Cover Release. Slide the battery compartment coverdown. Align the plastic connector of the Nickel-Cadmiumba...
Page 11 - Charging the Battery Pack; Initial Battery Charging; Charging from the Charging Cradle; CHARGE LED
Charging the Battery Pack Initial Battery Charging The rechargeable Nickel-Cadmium battery pack must be fully charged before using your phone for the first time. We recommend that the battery packcharge for approximately 15-20 hours, without interruption, before plugging the phone line into yournew ...
Page 12 - Continuous Battery Charging; Low Battery Indicator; During a Call; TONE; Adjusting Ringer Controls
Continuous Battery Charging For the best battery performance, return the Handset to the Base Unit at the end of the day. This keepsthe battery fully charged, so your phone works best. Low Battery Indicator When the Battery Pack in the Handset is very low and needs to be charged, the TALK/BATT LOW LE...
Page 13 - Automatic Digital Code Security
You can also select one oftwo different ringer tonesfor the Handset. Press @ to select a different ringer tone whenthe phone is not in use. To adjust the receivervolume, press while you are on a call. Handset Ringer Tone Select Button Handset Receiver Volume Control Automatic Digital Code Security T...
Page 14 - CHARGE; Using Your Phone; Making and Receiving Calls; press
4. When the beepingstops, briefly remove the Handset again, and then return it to the Base Unit. Mote: The CHARGELED will blink to indicate that the DigitalSecurity Code is set toone of the more than65,000 codes. If the Base Unit loses power while the Handset is off the Base, the Digital Code may be...
Page 15 - FIND; Programming Your Phone; Storing a Number in Memory
PRESS THESE YOU WILL HEAR KEYS Press A click similar to Note: Change when is channels to help pressed. CHANGING eliminate CHANNELS backgroundnoise. Changing Channels, Flash, and Page/Find To change channels or access call waiting while the phone is in use, or to use the one-way page to locate the Ha...
Page 16 - Storing a Mixed Number
4. If a pause is needed during dialing toaccess a long distance service press Note: The button counts as one digit. Pressing more than once increases the length of the pause between numbers. 5. Press again. 6. Enter the memory location (0-9). A tone indicates that the number is stored. Storing a Mix...
Page 17 - Dialing a Stored Number
4. Press on the Handset. 5. Enter the number to in tone 6. If a pause is needed during dialing toaccess a longdistance service, press The button counts as one digit. Pressing more than once increases the length of the pause between numbers. 7. Press again. 8. Enter the memory location (0-9). A tone ...
Page 19 - Troubleshooting
Troubleshooting If your XC610 Series/XC710 Cordless Telephone is not performing to your expectations, please try these simple steps. If you are still unable to resolve theproblems, contact Uniden Customer Service forassistance. Problem Suggestion Chanrge light won’t come l Make sure AC on when Hands...
Page 20 - General
Specifications WARRANTY General Frequency Control Modulation Operating Temperature Base Unit ReceiveFrequency Transmit Frequency PowerRequirements Size Weight Handset ReceiveFrequency Transmit Frequency PowerRequirements Size Weight Battety PLL F M - 10˚C to 50˚C 39.775 to 40.000 MHz (10 Channels) 3...
