Uniden UDW-10003 - Manual

5 Check the Video Signal As soon as the receiver powers on, it detects the camera and shows the video on the display. The icons at the top of the screen tell you what’s going on with the camera and receiver. The table below shows the different status icons and what they mean. Since the icons appear ...

6 Learning Your System Get to Know the Camera What the buttons do Button What it does POWER Turn the camera on. Press and hold to turn it off. LINk Enter pairing mode. What the lights mean Power Status light State What it means On The camera is on. Off The camera is off. Link Status light State What...

7 Using the camera mount The camera has a built-in stand so you can place it on any flat surface. If you want to place your camera on a wall or a ceiling (or even if you just want to secure it to a flat surface), you can use the included camera mount. (You might want to bring the receiver along when...

8 Get to Know the Receiver What the buttons do Button What it does MENU/Ok Open and close the menu - LEFT In zoom mode: pan to the left side of the zoom area. In the menu: cycle through the available options for the selected menu item. In quad display: go to channel 4. - - - RIGHT In zoom mode: pan ...

9 Button What it does DOWN In zoom mode: pan to the bottom of the zoom area. In the menu: move the cursor down one line. In quad display: go to channel 2. - - - SELECT CAMERA Cycle through the active cameras. From the pairing menu: link to the selected camera. - - ZOOM Enter and exit zoom mode. - PO...

10 Using the Menu Item Use it to Audio Vol Adjust the volume of the audio from the camera. Choose a value from 0 (off) through 20 (maximum). Scan Time Set the length of time the receiver spends on each active camera during a scan (see page 15) or activate quad display (see page 16). CAM1 – CAM4 Turn...

11 Using Zoom Mode The receiver can zoom in so you can see the video better. In zoom mode, the receiver increases the pixel size and focuses on the center of the picture. You will also see the ZOOM icon in the upper right corner of the display. Pan and tilt in zoom mode Once in zoom mode, you can pa...

12 Connecting to Your TV You can connect the receiver to any standard television with RCA composite video inputs. To use bandwidth efficiently, the system compresses the video signal using Motion-JPEG; the system then digitizes the signal before transmitting it to provide a secure video link. This m...

13 Multiple Camera Features Your receiver supports a total of four active cameras at a time. You can mix and match any of the accessory cameras. (See our website for compatible camera options.) Pairing Cameras Pairing is like introducing the camera and the receiver so they can communicate. You’ll pe...

14 Changing to a Different Camera On the receiver, press to cycle through the enabled channels from CAM1 through CAM4 . After the last enabled channel, the receiver goes back to the first camera. Each time you press , the receiver goes to the next enabled channel, regardless of whether there is a ca...

15 Setting Up a Scan You can have the receiver automatically cycle through the enabled channels. Open the menu, and scroll down to select Scan time . Use RIGHT or LEFT to select the amount of time you want the receiver to stay on each camera. Choose 5 seconds , 10 seconds , 15 seconds , or 20 second...

16 Using Quad Display In quad display, the receiver puts all four channels on the screen at the same time. The channels appear in the positions shown to the right: If a channel is disabled or there is no signal from the camera, that channel's section of the quad display will be blank. To enter quad ...

17 Solving Problems If you have any trouble with your system, try these simple steps first. If you still have a question, call our Customer Care Line listed on the front cover. If… Try.. The image on the display is too bright. Adjusting the brightness on the receiver (in the System Setup sub- menu)....

18 If… Try.. None of the buttons on the receiver respond when I press them. Resetting the receiver. - Unstable or Weak Signal If the video seems to lag and or the audio sounds weak, the camera and the receiver do not have a strong, clear signal between them. There are several causes for a weak signa...

19 Signal Level Icon Data Rate (kbps) Frames per second (approx) QVGA (Zoom) VGA (Normal) Perfect 1062~1280 15~20 5~10 Good 725~1062 12~16 3~5 Fair 543~725 8~12 2~4 Low 250~543 0~5 0~1 Zero 0~250 0 0 If the suggestions above don’t provide enough improvement in the the signal quality, you may want to...

20 If the static is only on 1 camera If the static is on all cameras Check near the camera for one of the common interference sources. Try moving the camera away from a suspected source, or try moving the suspected source so it’s not between the camera and the receiver. Try moving closer to the rece...

21 Additional Information Product Specifications Radio Frequency Transceiver RF Frequency 2402 Mhz ~ 2483.5 Mhz Modulation GFSK Spread spectrum Frequency Hopping Anti Interference Clean Channel Dynamic Select Selectable camera channel 4 Data rate 2 Mbps Channel bandwidth 2 MHz Transmitting range 200...

22 System Specifications Camera Receiver Low light solution 11 IR LEDs, 1 Low light sensor Low light sensitivity 1-8 lux Picture sensor OV7725 1/4’ Color CMOS Lens F3.6mm H:53 V:40 Output Jacks AV OUT : 3.5 mm headset jack to RCAUSB : USB 1.1 or above Polymer-Lithium Battery Warning CAUTION! Risk of...

23 FCC Compliance Information Part 15 Compliance Statement This device complies with Part 15 of the FCC Rules. Operation is subjected to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference...

One-year Limited Warranty Important: Evidence of original purchase is required for warranty service. WARRANTOR: UNIDEN AMERICA CORPORATION (“Uniden”) ELEMENTS OF WARRANTY: Uniden warrants, for one year, to the original retail owner, this Uniden Product to be free from defects in materials & craf...