Page 2 - INTRODUCTION; Congratulations on the purchase of your Uniden FP101 Telephone.
2 INTRODUCTION Congratulations on the purchase of your Uniden FP101 Telephone. The FP101 has been designed and engineered to exacting standards for reliability, long life and outstanding performance. To obtain the full benefit from your new telephone, please read this OperatingGuide thoroughly. For ...
Page 4 - CONTENTS
4 Accessing Call Waiting (New Zealand Model only) . . . . . . .18Accessing Call Waiting (Australian Model only) . . . . . . . . . .18Mute . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19Placing a Call on Hold . . . . . . . . . . . . . . . . . . . . . . . . . . . .1...
Page 5 - IMPORTANT INFORMATION; Follow all warnings and instructions marked on the product.; IMPORT
5 IMPORTANT INFORMATION When using your telephone equipment, basic safety precautions should always befollowed to reduce the risk of fire, electrical shock, and injury to persons,including the following: 1. Read and understand all instructions. 2. Follow all warnings and instructions marked on the p...
Page 6 - CARING FOR YOUR TELEPHONE; Clean your telephone using a soft damp cloth.; CAUTION
6 9. Unplug this product and refer servicing to qualified service personnel under the following conditions:A. If liquid has been spilled into the product.B. If the product has been exposed to rain or water.C. If the product does not operate normally when following the operating instructions. Adjust ...
Page 9 - FEATURES
9 FEATURES FEATURES • Pre-Programmed Feature Buttons Instant access to some of Telecom’s / Telstra’s most popular network service features* have been factory programmed into this telephone for your convenience.* Some of these services will require subscription. • 15 One Touch Speed Dial Buttons Your...
Page 10 - Bright red LED provides visual indication of an incoming call.; FEA
10 • Hearing Aid Compatible Inductive transducer coil handsets provide hearing aid compatibility. • Status LED Bright red LED provides visual indication and differentiation for calls 'In Use' or 'On Hold'. • Call LED Bright red LED provides visual indication of an incoming call. • Pause Button Allow...
Page 11 - AUSTRALIAN MODELS
11 FUNCTIONS FUNCTIONS 6 3 7 2 1 4 5 AUSTRALIAN MODELS 1. Button 2. Button 3. Button 4. Button 5. Button 6. One Touch Speed Dial Buttons7. Memory Storage Card 6 3 7 2 1 4 5 NOTE: If required the Memory Storage Card can be turned over to give 20 One Touch memory buttons, as shown below NEW ZEALAND MO...
Page 12 - call
12 FUNCTIONS FUNCTIONS 8 13 9 10 15 16 17 18 19 20 21 22 8. Button 9. Button 10. Button 11. Button 12. Handset Retainer Tab13. Button 14. Telephone Number Card 15. Numeric Keypad 14 16. call LED 17. status LED 18. Button 19. Button 20. Not used21. tone Slide Switch 22. Telephone Line Jack23. ringer ...
Page 13 - INSTALLATION; HANDSET CORD CONNECTION
• Never install telephone wiring during a lightning storm. • Never touch uninsulated telephone wires or terminals unless the telephone line has been disconnected. • Use caution when installing or modifying telephone lines. CAUTION 13 INSTALLATION INST ALLA TION HANDSET CORD CONNECTION Plug one end o...
Page 14 - WALL MOUNTING
INST ALLA TION INSTALLATION WALL MOUNTING You can mount your phone directly on a wall. Before mounting your phone,consider the following:• Select a location away from electrical cables, pipes or other items behind the mounting location that could cause a hazard when inserting screws into the wall. •...
Page 15 - USING
MEMORY DIAL NUMBERS 20 one touch speed dial numbers can be stored into the memory of your telephone. STORING ONE-TOUCH MEMORIES 1. To program One-Touch Memories ( ~ ). a. Pickup the Handset.b. Press the button. c. Enter telephone number that you want to program.d. Press the button. e. Press the spee...
Page 16 - DIALING STORED NUMBERS; button. The telephone will dial; CHAIN DIALING; PAUSE; button counts as one digit. Pressing
DIALING STORED NUMBERS For example, to dial memory 3 from the telephone1. Pick up the Handset.2. Press the button. The telephone will dial the number stored in this memory location. 3. After you have completed the Phone call, place the Handset back on the Base. CHAIN DIALING On certain occasions, af...
Page 17 - ADJUSTING THE RINGER VOLUME CONTROL; slide control to the desired position.; LED indicators; LED indicator: Red light which flashes when the; status
17 USING YOUR FP101 USING YOUR FP101 ADJUSTING THE RINGER VOLUME CONTROL While the phone is ringing, you can adjust the ringer volume of your telephone bymoving the ringer switch to the desired low/medium/high position. ADJUSTING THE RINGER TONE CONTROL While the phone is ringing, you can adjust the...
Page 18 - PLACING A TELEPHONE CALL
18 USING YOUR FP101 USING YOUR FP101 PLACING A TELEPHONE CALL 1. Remove the Handset from the Base.2. Press the keypad buttons to dial the phone number you want.3. After you have completed the phone call, place the Handset back on the Base. REDIAL If you want to redial the last number dialed, simply ...
Page 19 - MUTE; Pick up the handset, wait for the dial tone then press the; Divert On
19 USING YOUR FP101 USING YOUR FP101 MUTE Press and hold down the button to turn off the Handset microphone, allowing private and confidential conversations in the same room without the call-ing party hearing. Release the button again to resume the conversation with the calling party. PLACING A CALL...
Page 20 - Pick up the handset, listen for the dial tone, then press the; Example; Pick up the handset, and listen for the dial tone and then press; Divert Off; button, then dial the number
20 USING YOUR FP101 USING YOUR FP101 Pick up the handset, listen for the dial tone, then press the button. The telephone will automatically dial the access code ‘161’ and will enable ‘immediate call diversion’ to the number you have assigned the divert to. Wait forthe ‘confirmation tone’ (long-short...
Page 21 - Call Back
21 USING YOUR FP101 USING YOUR FP101 Call Back When the party you are calling is engaged or doesn’t answer, hang up.Pick up the handset, then press the button. The telephone will automatically dial the access code *’51’ to enable the ‘autocallback’ feature. Listen for an interrupted dial tone and ha...
Page 22 - Block CID
22 USING YOUR FP101 USING YOUR FP101 USING THE PRE-PROGRAMMED FEATURE BUTTONS (Australian Model Only) Instant access to some of Telstra’s most popular network service features havebeen factory programmed into this telephone for your convenience. Block CID Each time you make a call, your telephone nu...
Page 23 - button and then hang up.; Call Return; if you would like to be connected to this number.; Message Bank; key. Once you reach the main menu press
23 USING YOUR FP101 USING YOUR FP101 Divert Off To cancel ‘Call Forward No Answer’ to another number.Pick up the handset, press the button and then hang up. The telephone will automatically dial the access code ‘#61#’ and will cancel thediversion. Call Return Telstra’s ‘Call Return’ Service lets you...
Page 24 - If you live outside the Sydney area, you will need to re-program the; Brisbane
USING YOUR FP101 USING YOUR FP101 If you live outside the Sydney area, you will need to re-program the button as follows; Brisbane : Pick up the handset, then press Melbourne : Pick up the handset, then press Adelaide : Pick up the handset, then press Perth : Pick up the handset, then press Telstra ...
Page 25 - TROUBLESHOOTING
TROUBLESHOOTING Problem Can’t make or receive calls. Can’t hear the telephone ringing. One Touch Speed Dial Numbers are not working correctly.Handset does not hang up in the wall mountposition. Suggestion • Make sure you use only the line cord supplied with this telephone. • Check that both ends of ...
Page 26 - Specifications for New Zealand Model; Specifications for Australian Model; Compliance; SPECIFICATIONS
26 Specifications for New Zealand Model Compliance PTC200 Size: 150mm(W) x 225mm(D) x 70mm(H) Weight: Approx. 536g Specifications, Features and availability of Optional Accessories shown are typicaland subject to change without notice. NOTE: FOR USE OF THIS DEVICE IN NEW ZEALAND 1. The grant of a Te...
Page 27 - One-Year Limited Warranty
WARRANTY W ARRANTY One-Year Limited Warranty Important: Evidence of original purchase is required for warranty service. WARRANTOR: Uniden Australia Pty Limited ACN 001 865 498 Uniden New Zealand Limited ELEMENTS OF WARRANTY : Uniden warrants to the original retail owner for the duration of this warr...
Page 28 - THANK YOU; FOR
UNIDEN © 1998 Uniden Australia Pty Limited © 1998 Uniden New Zealand Limited THANK YOU FOR PURCHASING A UNIDEN PHONE! FP101-OM.qxd 7/12/98 09:12 Page 28
