Uniden EXS 9995 - Manual

3 INCLUDED IN YOUR PACKAGE To get the most from yourphone, please read thisowner’s manual thoroughly.Be sure to complete andmail the productregistration form. If any of these items aremissing or damaged,contact the Uniden PartsDepartment at (800) 554-3988. Hours are from 8:30a.m. to 5:00 p.m. Centra...

Before choosing a location for your new phone, read the Installation Considerationsincluded in the Precautions and Important Safety Instructions brochure. Here aresome important guidelines you should consider: • The location should be close to both a phone jack and a continuous poweroutlet. (A conti...

1. Plug the AC adapter cord into the 10V DC input jack on the back of the base. 2. Wrap the AC adapter cord around the strain relief notch. 3. Plug the AC adapter into a standard 120V AC wall outlet. 4. Charge the battery (refer to Charging the Battery Pack, page 9). 5. Plug one end of the long tele...

▼ Standard wall plate mounting This phone can be mounted on any standard telephone wall plate. 1. Snap the wall mount adapter into the bottom of the base as shown. 2. Plug the AC adapter into the base. 3. Place the AC adapter cord inside the molded wiring channel. Wrap the cord around the strain rel...

1. Press the battery cover release. Slide cover off. 2. Install the nickel-cadmium battery with the label down. 3. Slide the battery cover forward until it snaps into place 8 INSTALLING THE HANDSET BATTERY PACK Use only Uniden Battery(model BT-999) suppliedwith your phone. EXS9995 11/9/00 15:54 Page...

▼ Initial battery charging Before connecting your phone for the first time, charge the rechargeable battery packfor 15-20 hours without interruption. 1. Place the handset on the base. 2. Make sure that status LED lights. If the LED doesn’t light, be sure the ACadapter is plugged in and the handsetma...

▼ Low battery indicator When the battery pack is very low and needs tobe charged, the phone is programmed toeliminate some functions to save power. If thephone is not in use, <Low Battery> flashes. If the phone is in use, <Low Battery> flashes and the handset beeps. 10 CLEANING THE BATTE...

▼ Handset ringer volume Remove the handset from the base. Press the vol ▲ or ▼ key on the handset to set the handset ringer volume. There are two ringervolume settings; high and low. To select the high volume setting, press vol ▲ key. The following screen displays: To select the low volume setting, ...

▼ To attach the beltclip Insert the beltclip into the holes on eachside of the handset.Press down until it clicks. ▼ To remove the beltclip Pull both side of the tabs from the holes. 12 INSTALLING THE BELTCLIP If you have wall mountedthe base, you must removethe beltclip to charge thehandset with fa...

▼ Basic 2-line operation 14 USING YOUR NEW PHONE Fold out the front cover ofthis owner’s manual to usethe CONTROLS ANDFUNCTIONS diagram for reference. MAKING AND RECEIVING CALLS Handset On Base AutoTalk On - Pick up handset. AutoTalk Off - Pick up and press line 1 or line 2 . To answer a call Handse...

When you have connected power and a telephone line to your EXS 9995, the phone is in “ Standby mode ”, ready to receive and make calls. For clarity, the instructions in this User’s Manual designates line 1 unless theprocedure requires using line 2. The same instructions apply to line 2. 15 ANSWERING...

1. The handset rings and the following screen appears: 2. Press line 1 to answer your call. Current volume setting appears on theLCD display. 3. When you finish the call press line 1 on the handset, or return the handsetto the base. 16 ANSWERING A CALL FROM THE HANDSET MAKING A CALL FROM THE HANDSET...

▼ Dialing from Standby Mode 1. Pick up the handset. 2. Use one of the memory features. (See Using Memory Dialing, page 32). 3. Press line 1 . 4. When you finish the call, press line 1 , or return the handset to the base. 17 USING THE TONE FEATURE FLASH AND CALL WAITING You may enter a pause in the d...

Use the redial key to recall the last 3 numbers dialed. The redialed number can be up to 32 digits long. To redial from the handset: Press redial repeatedly to display the number you want to dial, then press line 1 . Or, press line 1 before redial, only the last number dialed can be accessed for red...

You can mute your conversation from the base. This prevents the party you arespeaking to from hearing what you, or someone else in the room, is saying. For example, to use this privacy feature while using line 1. 1. Press mute . The line 1 LED flashes red. You can hear the party on line 1, but they ...

▼ From the Base to the Handset 1. Press page/int’com on the base. The handset beeps. (If no answer, press page/int’com again to disconnect.) 2. Press int’com/p on the handset. Speak into the mouthpiece to answerthe page. To hang up at the base: Press page/int’com . To hang up at the handset: Press i...

▼ From Handset to Base 1. To transfer a call on line 1 from the handset to the base, press hold . The line 1 LED turns red on the base. 2. On the handset, press int’com/p . The status LED flashes on the base. The following screen appears: 3. Answer at the base by pressing page/int’com . You may then...

Your EXS 9995 stores up to 30 name/numbers in the handset.Memory locations are shared by both lines. ▼ On the Handset 1. Remove the handset from the base. 2. Press and hold mem for two seconds. The following screen appears: 3. Use the ▲ and ▼ keys, or enter a two digit number (01-30), to choose them...

To edit a number you have stored in the handset: 1. Remove the handset from the base. 2. Press and hold mem for two seconds. The display shows the Memory Storescreen and any saved name/numbers. 3. Use the ▲ and ▼ keys or enter a two digit number (01-30) to select thememory location you would like to...

After erasing a number, you may add a new address to memory. ▼ From the Handset 1. Remove the handset from the base. 2. Press and hold mem for two seconds. The handset shows the Memory Store screenwith saved name/numbers displayed. 3. Use the ▲ and ▼ keys, or enter a two digit number (01-30), to sel...

Follow the steps below to dial a number using a programmed memory location: ▼ Standby Mode Dialing from the Handset 1. Press mem . The handset displays your programmedmemory locations. 2. Use the ▲ and ▼ keys to select the memory location you would like to dial.Or, you may enter a two digit number(0...

You must subscribe to Caller ID from your phone company to usethis feature. ▼ Setting up Caller ID options There are three Caller ID options available; they are AutoTalk, CIDCW, and Area Code. AutoTalk allows you to answer the phone without pressing line 1 or line 2 . If the phone rings when AutoTal...

Your EXS 9995 2-Line answering system operates independently for each phone line.To review messages and record personal greetings, you must first select theappropriate line using the “ msg line select ” key. ▼ Turning the answering system on/off Press “ msg line select ” to select line 1 or line 2 ....

3. Next, press skip or repeat until you hear the correct hour setting. (Numbers 1 through 12 display on the base as each hour is announced.) Press clock again to select the correct time. 4. Press skip or repeat until you hear the correct time setting. (Numbers 0 through 59 display on the base as eac...

You can set your answering system to record messages up to one or four minuteslong. There are two separate REC TIME switches on the side of the base unit, one foreach line. One minute option: move the REC TIME switch to 1. Four minutes option: move the REC TIME switch to 4. ▼ Announce only feature: ...

The ring time switch is common for line 1 and line 2 . The ring time/toll saver switch allowsyou to set the number of rings the callerhears before the answering system playsyour greeting message. You can set theswitch to answer after two rings or afterfour rings. Once the greeting hasstarted, you ca...

▼ Playing your messages The base display shows the number of total messages received on each line. If thedisplay is blinking, then there are new messages waiting for you. The EXS 9995 isdesigned to play your new messages first. After you play your new messages, you canthen play your old messages.Pre...

1. Press play/stop to review your message. The number of stored messages is announced. 2. After a message has played for a few seconds, press repeat to repeat the message. 3. Press play/stop at anytime to stop reviewing messages and return to standby. Themessage counter LED shows the totalnumber of ...

▼ Deleting individual message Press “ msg line select ” to select line 1 or line 2 . The selected line LED lights. 1. Press play/stop to review your message. 2. If you decide to delete a message, press delete anytime during the message. The system beeps and immediately goes to thenext message. 3. Af...

Press “ msg line select ” to select line 1 or line 2 . The selected line indicator lights. You can record up to 10 minutes of conversation while you are making your call. 1. During the conversation, press and hold voice memo on the base. When it starts recording, the LED blinks. A beepthat can be he...

You can operate your answering system from a remote location using any touch-tonetelephone. Use this function to check for recorded messages, to play or deletemessages, even to record a new greeting message, and to monitor sounds in the room. 1. Call your telephone number. (Either line 1 or line 2 )...

You can call your answering system from any touch-tone phone and monitor soundsin the room where your base is installed. 1. Call your telephone number. (Either line 1 or line 2 ) 2. While the answering machine is activated, press # and your PIN code. 3. The answering system begins announcing the tim...

If your phone is not performing to your expectations, please try these simple stepsbefore calling Uniden customer service at (800) 297-1023 . 53 QUICK REFERENCE CHART TROUBLESHOOTING YOUR NEW PHONE PROBLEM SUGGESTION The charge light won’tcome on when thehandset is placed inthe base. • Make sure the...

At Uniden, we’ll take care of you! If you need any assistance with this product, please call our Customer Hotline at 1-800-297-1023 PLEASE DO NOT RETURN THIS PRODUCT TO THE PLACE OF PURCHASE. Our Uniden representatives will be happy to help you with any matters regarding the operation of this unit, ...