Uniden EXS 2010 - Manual

3 Make sure you have received the following items in the package.If any of these items are missing or damaged, contact the Uniden Parts Department (see below). • Base unit • Handset • AC adapter (AD-310) • Rechargeable battery pack (BT-905) • Telephone line cord (2) • Wall mount adapter • Beltclip •...

4 Do the following steps. • Choose the best location• Connect the base unit• Choose the dialing mode Choose the best location Before choosing a location for your new phone, read theINSTALLATION CONSIDERATIONS included in the PRECAUTIONSAND IMPORTANT SAFETY INSTRUCTIONS brochure. Here are someimporta...

5 Connect the base unit If you want to install the base unit on the wall, see page 7. Route the cord. To AC outlet To telephone outlet To TEL LINE To DC IN 9V AC adapter(supplied) Telephone line cord(supplied) 1 2 Place the power cord so itdoes not create a triphazard, or where it couldbecome chafed...

6 Use only the supplied AD-310 ACadapter. Do not use any other ACadapter. Connect the AC adapter to acontinuous power supply. Place the base unit close to the AC outlet so that you can unplug theAC adapter easily. If your telephone outlet isn't modular,contact your telephone company forassistance. P...

7 Standard wall plate mounting This phone can be mounted on any standard telephone wallplate. 1 Snap the wall mountadapter into thenotches on the base. 2 Plug the telephoneline cord to the TEL LINE jack and the AC adapter to the DC IN 9V jack. 3 Plug the telephoneline cord into thetelephone outlet. ...

8 Direct wall plate mounting If you don't have a standard wall plate, you can mount your phonedirectly to the wall. Before doing this, consider the following:• Avoid electrical cables, pipes, or other items behind the mounting location, that could cause a hazard when inserting screws into the wall. ...

9 Installing the handset battery pack Charge the battery pack for 15 - 20 hours before you start usingyour phone. 1 Press the battery coverrelease. 2 Connect the battery packconnector with the correctpolarity (black and redwires), then insert the batterypack into the batterycompartment. 3 Slide the ...

10 Battery use time (per charge) From fully charged• Six hours coutinuous use.• Ten days when the handset is in the standby mode. When the battery charge becomes low When the voltage of battery pack in the handset is very low andneeds to be charged, the phone is programmed to eliminatefunctions in o...

11 1 Press . Listen for dial tone. 2 Dial the phone number. 3 To hang up, press or returnthe handset to the base. Other Operations To Do this To adjust the ear speaker volume Press or during the call. To temporarily switch to tone dial Press . The following (When the base is set to pulse numbers wil...

12 Handset on the base 1 Phone rings. The talk/batt LED blinks. 2 Pick up the handset and beginspeaking. 3 To hang up, press or return thehandset to the base. Handset off the base 1 Phone rings. The talk/batt LED blinks. 2 Press or any key (except ) and begin speaking. 3 To hang up, press or return ...

13 Ringer tone/volume The phone has four types of ringer tone and volume combinations.In standby mode, press repeatedly on the handset. To turn the ringer off, set the ringer on/off switch to off . Handset earpiece volume The phone has four earpiece volume levels, Normal, Medium, High,and Loud. Pres...

14 The last phone number dialed can be quickly redialed. 1 Press . The talk/batt LED lights. 2 Press . 3 To hang up, press or place thehandset on the base. If the recently dialednumber exceeds 32 digits,only the first 32 digits canbe redialed. Redialing a call talk redial talk EXS 2010 6/28/00 4:12 ...

15 You can turn off the handset microphone and temporarily mutethe ringer. talk 1 Press during a telephone call.The talk/batt LED flashes. The other party will not be able tohear you although you can hearthem. 2 To cancel mute, press or again. Mute mute talk When speaking on thehandset mute Press wh...

16 To locate the handset (while it’s off thebase), press on the base. Thehandset beeps for 5 seconds. page/find page/fin d power status D I G ITA L S P R E A D SPECTR AM 9 00 M H z Using page feature If you cancel the page bypressing , press again to return to standby. talk talk Press and hold for m...

17 Your EXS 2010 stores up to 10 numbers in the handset. 1 Press while in standby mode.The talk/batt LED flashes. 2 Dial the number you wish to store (upto 20 digits). 3 Press again. 4 Press a number key (0 - 9) to selectthe memory location where youwish to store the number. 5 The talk/batt LED goes...

18 Memory dialing 1 Press . The talk/batt LED lights. 2 Press . 3 Enter a number (0 - 9) to select thememory location you wish to dial. 4 To hang up, press or return thehandset to the base. Making calls with memory dialing talk mem talk Chain dialing On certain occasions after dialing a number, you ...

19 1 Press in the standby mode.The talk/batt LED flashes. 2 Press again. 3 Enter the memory location number (0 - 9) you wish to delete. A confirmation beep indicates thenumber has been erased. mem Erasing a stored phone number mem EXS 2010 6/28/00 4:12 PM Page 23

20 To attach the beltclip Insert the beltclip into the holeson each side of the handset.Press down until it clicks. To remove the beltclip Pull both sides of the beltclip torelease the tabs from the holes. Your phone may be used with an optional headset, the Uniden HS910. To use this feature, simply...

21 Battery replacementand handling When the operating timebecomes short, even after abattery is recharged, pleasereplace the battery.With normal usage, yourbattery should last about oneyear.Please contact your place ofpurchase for a replacementbattery. RECYCLING NICKEL-CADMIUM BATTERIES NICKEL-CADMI...

22 If your phone is not performing to your expectations, please trythese simple steps first. Symptom The power LED won't come on. The status LED won't come on when thehandset is placed inthe base unit. The audio soundsweak and/or scratchy. Can't make or receivecalls. The handset doesn'tring or recei...

24 A, B Battery pack Preparing and charging ............................9Replacement and handling ..........................21 Beltclip installation ...............20 C Chain dialing.........................18Connection..............................5 D Dialing mode ..........................6Digital...