Uniden DECT3380 - Manual

5 If you have a DRX332 handset with a MULTIRANGE ™ charger, be sure to use the correct AC adapter for the charger. Refer to the table on page 2 for a list of adapters/voltage requirements. For MULTIRANGE chargers, route the cord as shown: Plug the other end of each adapter into a standard 120V AC po...

Your base supports a total of two (2) DRX332 MULTIRANGE chargers, including any that were supplied with your phone. To use the charger's MULTIRANGE function, you must register the charger to a DECT3380 base. Any MULTIRANGE chargers packaged with your base are registered and ready to use out of the b...

8 the base, there may be interference from electronic devices, or the signal might be blocked by thick walls or metal objects. Try moving the charger to another location. UNDERSTANDING YOUR PHONE Parts of the Base UP REV DOWN FWD FIND Charging contacts DELETE PLAY/ STOP DO NOT DISTURB ON/OFF Message...

9 Base keys and how they work Key name (and icon) What it does find In standby: page all handsets to find a lost one. - do noT disTurb ( ) In standby: turn the Do Not Disturb feature on or off (see page 21). - on/off In standby: turn the answering system on or off. - rEV ( ) While a message is playi...

10 Parts of the Handset Microphone Twelve- key dial pad Visual ringer Display Charging contacts Earpiece UP PHONEBOOK/ LEFT SPEAKER DOWN CALLER ID/ RIGHT REDIAL/ PAUSE MUTE CLEAR/ INTERCOM MENU/SELECT END TALK/ FLASH MESSAGES Handset keys and how they work Key name (and icon) What it does uP ( ) In ...

11 Key name (and icon) What it does End ( ) During a call: hang up.In the menu or any list: exit and go to standby. - - CLEar/inTErCoM In standby: page another handset using the intercom.During a call: put the call on hold and start a call transfer.While entering text: delete one character, or press...

12 Display icons and what they mean Since the icons appear based on what you’re doing with the phone, you won’t ever see all of these icons at the same time. Icon What it means The ringer is turned off: this handset will not ring when a call comes in. You have a voice message waiting (see page 22). ...

13 Using the Menus Handset Setup Ans. Setup Day & Time To open the menu, press MENU/SELECT . Press MENU/SELECT to choose the highlighted option . press END to exit the menu . To go back a screen, press PHONEBOOK/LEFT The cursor shows the highlighted option. To move the cursor, use UP & DOWN ...

14 Banner Change the name used on the handset’s display. Handset Language Change the display language. Key Touch Tone Have the keypad sound a tone when you press a key. The Ans. Setup menu This menu controls the options and settings for your answering system (see page 22). The Day and Time menu If y...

15 The phone defaults to a capital letter for the first letter and any letter after a space; otherwise, it uses small letters. To switch to all capital letters, press * . The phone defaults to all capital letters first (e. g. ABCabc2) until you enter a blank space or press * again. (Any time you wan...

1 To... Do this from the earpiece... from the speaker... switch between the speakerphone and earpiece Press sPEakEr . mute the ringer for this call only While the phone is ringing, press MuTE . Change the volume Speaker and earpiece volume Ringer volume You can change the volume of the speaker on th...

17 current call and the waiting call, press TaLk/fLash . Remember, each time you switch, there is a short pause before you’re connected to the other caller. Using Caller ID and Redial Lists Caller ID (CID) is a service available from your telephone provider that shows the phone number (and sometimes...

18 To select a number, highlight the number and press MEnu/sELECT . The phone gives you the following options: Delete Entry Erase the number from the list. Store Into Pb Add the number to the phonebook. The handset prompts you to edit the name and number and select a personal ringtone. Delete All (C...

19 Phonebook menu options With the phone in standby, open the phonebook. From the main phonebook screen (instead of an individual entry), press MEnu/sELECT . The phone gives you the following options: Create New Add an entry to your phonebook. The handset prompts you to enter a name and number and s...

20 Conference calling When an outside call comes in, two handsets can join in a conference call with the outside caller. To join an ongoing call, press TaLk/fLash or sPEakEr . To leave the conference call, hang up normally; the other handset remains connected to the call. Privacy mode You can preven...

21 Intercom Whenever the phone is in standby, you can make an intercom call between handsets without using the phone line. You can make an intercom call from any handset, but only two handsets can be in an intercom call at any time. If an outside call comes in during an intercom page, the phone soun...

22 Chain dialing If you often have to enter a series of digits or a code number during a call, you can save that code number to a phonebook entry and use the phonebook to send the code number. Enter the code number (up to 20 digits) into the phonebook just like a regular phonebook entry. Be sure to ...

23 Record Time Set the amount of time callers have to leave a message, either 1 minute or 4 minutes. Choose Announce Only if you don’t want the system to let callers to leave a message. Message Alert Have the system beep every 15 seconds when you have a new message; the beeping stops when you listen...

24 You can press the number key next to the commands instead of scrolling through them. If you don't press any keys for 30 seconds, the phone returns to standby. Only one handset can access the system at a time, and you can't access the system while another handset is on a call. Personalizing Your G...

25 Getting Your Messages To… from the base... from a handset (remote operation) ... play new messages Press PLaY/sToP. Press MEssagEs . The system announces the number of new and old messages, then plays each new message (followed by the time and day) in the order it was received. replay an earlier ...

2 handset at a time can screen calls. If another handset is screening the call, the handset beeps and returns to standby. To... from the base... from a handset... hear the caller leaving a message Just listen to the caller over the speaker. Press MEssagEs . answer the call Not available. Press TaLk/...

27 During the greeting (or beeps), press 0 and immediately enter your security code. (If you enter it incorrectly 3 times, the system hangs up and returns to standby.) The system announces the current time, the number of messages stored in memory, and a help prompt. Then it starts beeping intermitte...

28 If… Try… A handset is not working. Charging the battery for 15-20 hours.Checking the battery connection.Resetting the handset. - - - A handset says Unavailable . Moving the handset closer to the base.Seeing if another handset is in Privacy Mode. - - No handsets display Caller ID information. Lett...

30 Installing a line filter or DSL filter Sometimes, broadband Internet services that use the telephone line can interfere with phones. One of these services−DSL−often causes static on telephones. A DSL filter or telephone line filter usually solves this problem. The technician who installed your DS...

31 CAUTION! DO NOT use a microwave oven to speed up the drying process. This will cause permanent damage to the handset, base and the microwave oven. Changing from Tone to Pulse Dialing Your phone communicates with the telephone network two ways: tone dialing or pulse dialing. Most telephone compani...

32 Registering a handset When you reset a handset (or if you buy a new one), that handset displays a Handset Not Registered message. If you see this message on a handset, you need to register it to a base before you can use it. Does the handset fit in the base cradle? Yes No Place the handset in the...

33 On the bottom of the MULTIRANGE charger, press and hold the registration button until the Link light starts to blink (about 2 seconds). Release the button and wait for the Link light to turn on and steady (this can take about 90 seconds). If the Link light doesn't turn on or keeps blinking, disco...

34 With normal use, the battery should last about one year. Replace the battery when the talk time becomes short even when the battery is charged. To buy a replacement battery, call the Parts Department listed on the front cover. Rechargeable Nickel-Metal-Hydride battery warning This equipment conta...

accessory supplied with this product. (All necessary accessories are included in the package; any additional or optional accessories are not required for compliance with the guidelines.) Third party accessories (unless approved by the manufacturer) should be avoided as these might not comply with FC...

Uniden America Service 4700 Amon Carter Blvd. Fort Worth, TX 7155 As an Energy Star ® Partner, Uniden has determined that this product meets the Energy Star ® guidelines for energy efficiency. Energy Star ® is a U.S. registered mark. Uniden ® is a registered trademark of Uniden America Corpora- tion...