Troy-Bilt 9528 - Manual

7 NOTE: If the flange keepers will not easily click into place, use the palm of your hand to apply swift, firmpressure to the back of each. 5. Remove the clevis pin and hairpin clip from the upper portion of the chute mast. • Position the control head over the chute mast and rear portion of the chut...

8 SECTION 3: KNOW YOUR SNOW THROWER WARNING: Read, understand, and follow all instructions and warnings on the machine and in this manual before operating. NOTE: For detailed starting instructions and more information on all engine controls, refer to the Tecumseh Engines manual packed separately and...

9 Auger Control The auger control is located on the left handle. Squeeze the control grip against the handle to engage the augers and start snow throwing action. Release to stop. Drive Control The drive control is located on the right handle. Squeeze the control grip against the handle to engage the...

10 SECTION 4: OPERATING YOUR SNOW THROWER Before Starting WARNING: Read, understand, and follow all instructions and warnings on the machineand in this manual before operating. Gas & Oil Fill-Up Service the engine with gasoline and oil as instructed in the Tecumseh Engines manual packed separate...

11 • Pull the starter handle with a firm, rapid stroke. IMPORTANT: Do not release the handle and allow it to snap back. Keep a firm hold on the starter handle and allow it to slowly recoil. • As the engine warms, slowly rotate the choke control to the OFF position. If the engine falters, quickly rot...

12 • Retighten the hex jam nut. See Figure 1. • Repeat Auger Control Test to verify proper adjustment has been achieved. Figure 1 Chute Clean-Out Tool The chute clean-out tool is conveniently fastened to the rear of the auger housing with a mounting clip. Should snow and ice become lodged in the chu...

13 SECTION 5: MAKING ADJUSTMENTS WARNING: Never attempt to make any adjustments while the engine is running,except where specified in operator’s manual. Shift Rod Adjustment If the full range of speeds (forward and reverse) cannot be achieved, refer to the figures to the right and adjust the shift r...

14 Drive Control When the drive control is released and in the disengaged “up” position, the cable should have very little slack. It should NOT be tight. Check the adjustment of the drive control as follows: 1. With the drive control released, push the snow thrower gently forward. The unit should ro...

15 SECTION 6: MAINTAINING AND SERVICING YOUR SNOW THROWER WARNING: Before lubricating, repairing, or inspecting, disengage all controls and stop engine. Wait until all moving parts have come to a complete stop. Engine Refer to the separate Tecumseh Engines manual packed with your unit for all engine...

16 Auger Belt Replacement To remove and replace your snow thrower’s auger belt, proceed as follows: 1. Remove the plastic belt cover on the front of the engine by removing the two self-tapping screws. • Drain the gasoline from the snow thrower, or place a piece of plastic under the gas cap. • Carefu...

17 Drive Belt Replacement To remove and replace your snow thrower’s auger belt, proceed as follows: 1. Remove the plastic belt cover on the front of the engine by removing the two self-tapping screws. • Drain the gasoline from the snow thrower, or place a piece of plastic under the gas cap. • Carefu...

18 Friction Wheel Removal If the snow thrower fails to drive with the drive control engaged, and performing the drive control cable adjustment on page 14 fails to correct the problem, the friction wheel may need to be replaced. Follow the instructions below. Examine the friction wheel for signs of w...

20 SECTION 8: TROUBLE SHOOTING GUIDE NOTE: For repairs beyond the minor adjustments above, contact your local authorized service dealer. Trouble Possible Cause(s) Corrective Action Engine fails to start Fuel tank empty, or stale fuel. Blocked fuel line.Choke control not in ON positionFaulty spark pl...

22 19 1 17 47 9 48 3 25 15 8 28 35 40 5 30 21 10 7 22 13 18 16 26 4 24 6 41 15 2 49 55 54 56 50 36 42 37 38 46 11 31 32 14 33 23 29 27 12 34 39 52 53 51 57 57 20 43 44 45 SECTION 9: PARTS LIST

23 Style Q REF. NO. PART NO. DESCRIPTION 1 631-04127 Panel Assembly, Handle, Q-Style(Inc. Ref. 47) 2 631-04133 Handle Assembly, Clutch Lock, LH(Inc. Ref. 48) 3 631-04134 Handle Assembly, Clutch Lock, RH(Inc. Ref. 48) 4 684-04105 Handle Assembly, Engagement, LH 5 684-04106 Handle Assembly, Engagement...

MANUFACTURER’S LIMITED WARRANTY FOR: The limited warranty set forth below is given by Troy-Bilt LLC with respect to new merchandise purchased and used in the United States and/or its territories and possessions, and by MTD Products Limited with respect to new merchandise purchased and used in Canada...