GE Washer Not Spinning: Causes and How to Fix It
Updated · from manufacturer service documentation
A GE washer that won't spin is diagnosed through three specific fault codes: Lock Monitor, Lid Monitor, and Locked Motor Monitor — each pointing to a different part of the chain between the lid switch and the drive motor. The service diagnostic includes a built-in Spin Test that can distinguish a bad hall sensor from an actual motor problem.
What Causes a GE Washer Not to Spin
| Cause | Likelihood | DIY difficulty | Related part |
|---|---|---|---|
| Lid lock not engaging or signal not reaching the control (Fault 1) | Common | Moderate — check lid lock resistance/harness | Lid lock assembly |
| Control not getting lid-closed signal during motor operation (Fault 2) | Common | Moderate — check switch/connection | Lid switch |
| Motor not turning or hall sensor disconnected (Fault 3) | Less common | Moderate — Spin Test diagnostic | Hall sensor / motor |
| Physical obstruction preventing motor movement | Less common | Easy — check for jams | — |
| Thermal cutoff (TCO) tripped | Rare | Easy — wait ~45 min, or check motor freedom | Motor |
How to Fix a GE Washer That Won't Spin, Step by Step
-
Check the lid lock assembly (Fault Code 1, Lock Monitor)
This triggers when the lid lock didn't engage, or its signal never reached the control due to a connection issue. Check the resistance of the lid lock assembly and the harness for open wires or loose connectors; replace the lid lock assembly if both test good but the fault persists.
-
Check the lid switch (Fault Code 2, Lid Monitor)
This triggers when the control doesn't get a lid-closed signal from the switch while the motor is moving — either the switch itself didn't close, or the connection is bad. If this fault repeats, the control itself may need replacing.
-
Run the Spin Test to isolate a hall sensor problem (Fault Code 3, Locked Motor Monitor)
This fault triggers when the control doesn't see signal changes indicating the motor is turning for 5 straight seconds during spin. Put the washer in Service Mode and run Test 14 (Spin Test): if the hall sensor is bad or disconnected, the basket will start spinning normally and then stop after about 5 seconds. If the basket spins for about 15 seconds, the hall sensor is most likely NOT the cause.
-
Check the motor for physical obstructions
Confirm nothing is jamming the motor or preventing it from moving freely — this is checked before assuming an electrical fault.
-
Check for a tripped thermal cutoff (TCO)
The TCO should reset on its own in about 45 minutes. If it's tripped, verify the motor moves freely; replace the motor if it doesn't.
-
Check the harness and connectors between the control and the motor
Including confirming the hall sensor is properly connected to the main harness.
Which Models This Applies To
Documented for the GE GTW750 (2018) top-load washer platform. The control stores up to 10 faults, and there are 32 different fault codes total that can be sensed on this platform — Fault Codes 1–3 specifically cover the lid-lock-to-motor chain relevant to a non-spinning washer.
See also: Washer not spinning (cross-brand).
Frequently Asked Questions
How do I know if it's the hall sensor or the motor itself?
Run the Spin Test (Test 14) in Service Mode: if the basket spins normally for about 5 seconds and then stops, the hall sensor is likely bad or disconnected. If it spins for about 15 seconds, the hall sensor probably isn't the cause.
What is a thermal cutoff (TCO), and does it fix itself?
Yes — it should reset on its own in about 45 minutes. If it keeps tripping, check that the motor moves freely; if it doesn't, the motor needs replacing.
What's the difference between Fault Code 1 and Fault Code 2?
Fault 1 (Lock Monitor) means the lid lock itself didn't engage or signal properly. Fault 2 (Lid Monitor) means the control lost the lid-closed signal specifically while the motor was already running — a related but distinct failure point.
How many fault codes can this washer store?
The control holds up to 10 faults out of 32 possible codes on this platform — check Consumer Error Mode or Service Mode Test 1 to view them.
Based on the GE GTW750 (2018) washer service documentation. Last updated: .