Page 2 - INTRODUCTION; Also be sure to read and follow ALL precautions; TABLE OF CONTENTS; Traxxas Support
2 • X O -1 INTRODUCTION Thank you for purchasing the XO-1. ™ This model is capable of extreme performance and high speeds unsurpassed by any other R/C vehicle, with the durability and ease of use that are hallmarks of Traxxas’ Ready-To-Race ® models. The included TQi 2.4GHz transmitter with Docking ...
Page 3 - The XO-1 is designed for use with LiPo batteries.; NEVER USE A NIMH OR NICD CHARGER TO CHARGE LIPO BATTERIES AS; Safety Is Your Responsibility!; SAFETY PRECAUTIONS
X O -1 • 3 Experts Only! This product is not a toy. This product carries our highest skill level rating, 10, and is not intended for use by children or minors under the age of 16. Individuals under the age of 18 require responsible adult supervision during operation and maintenance. The XO-1 is only...
Page 4 - LiPo; Skill Level = Myriad Semi Bold; bluehighway font
4 • X O -1 SAFETY PRECAUTIONS All of us at Traxxas want you to safely enjoy your new model. The precautions outlined in this manual should be strictly followed to help ensure safe operation. You alone must see that the instructions are followed and the precautions are adhered to. The XO-1 is optimiz...
Page 6 - Note that your hobby dealer; The Power System is; NOT WATERPROOF; Refers you to a page with a related topic.; Support; BEFORE YOU PROCEED
6 • X O -1 The XO-1 features a Castle Creations Brushless System pre-installed from the factory. The XO-1 is manufactured by Traxxas and is backed by full Traxxas factory support. The installed Mamba Monster Extreme power system (electronic speed control, motor, on/off switch) is manufactured by Cas...
Page 7 - Recommended Equipment; SUPPLIED TOOLS AND EQUIPMENT
X O -1 • 7 TOOLS, SUPPLIES, AND REQUIRED EQUIPMENT Recommended Equipment These items are not required for the operation of your model, but are a good idea to include in any R/C toolbox:• Safety glasses• Traxxas Ultra Premium Tire Glue, part #6468 (CA glue) • Hobby knife• Side cutters and/or needle n...
Page 9 - QUICK START: GETTING UP TO SPEED
X O -1 • 9 QUICK START: GETTING UP TO SPEED The following guide is an overview of the procedures for getting your model running. Look for the Quick Start logo on the bottom corners of Quick Start pages. 1. Read the safety precautions beginning on page 3 6. Check servo operation • See page 16 For you...
Page 10 - Applying the Decals
10 • X O -1 TRAXXAS TQ i RADIO SYSTEM Applying the Decals The main decals for your model have been applied at the factory. The decals are printed on self-adhesive clear mylar and are die-cut for easy removal. Use a hobby knife to lift the corner of a decal and lift it from the backing. To apply the ...
Page 11 - IMPORTANT RADIO SYSTEM PRECAUTIONS; Correct
X O -1 • 11 TRAXXAS TQ i RADIO SYSTEM TRAXXAS TQ i RADIO SYSTEM Neutral position - The standing position that the servos seek when the transmitter controls are at the neutral setting. NiMH - Abbreviation for nickel-metal hydride, the most common radio-control battery type. NiMH packs have lower curr...
Page 12 - MODEL WIRING DIAGRAM; ESC/Motor Wiring Diagram; TRANSMITTER AND RECEIVER; Castle Creations
12 • X O -1 Your model is equipped with the newest TQi 2.4GHz transmitter with Traxxas Link ™ Model Memory. The transmitter has two channels for controlling your throttle and steering. The receiver inside the model has 5 output channels. Your model is equipped with one servo and an electronic speed ...
Page 13 - INSTALLING TRANSMITTER BATTERIES; When operating the XO-1 with 2S LiPo or NiMH batteries and; SELECTING A CHARGER FOR YOUR MODEL; Use the Right Batteries
X O -1 • 13 TRAXXAS TQ i RADIO SYSTEM INSTALLING TRANSMITTER BATTERIES Your TQi transmitter uses 4 AA batteries. The battery compartment is located in the base of the transmitter.1. Remove the battery compartment door by pressing the tab and sliding the door open. 2. Remove the battery holder. Insta...
Page 14 - • Height with stock strap:; INSTALLING & REMOVING THE BATTERY PACKS; Always remove the batteries from the model before recharging.; Removing the Battery Packs; Insert the battery into the tray with the High Current Connector; Adjusting The Battery Compartment Length; Battery Compartment Height Chart
14 • X O -1 TRAXXAS TQ i RADIO SYSTEM 4 The following Traxxas High Current Connector packages are available from your hobby dealer. When using adapters, be careful not to exceed the current rating of the Molex connector. Battery Compartment Specs:• 49.5mm (1.95 ” ) wide x 155mm (6.10 " ) long (s...
Page 15 - RADIO SYSTEM RULES; Weak batteries will limit the radio signal between the; RADIO SYSTEM BASIC ADJUSTMENTS; Throttle Neutral Adjustment; Refer to page 18 for instructions.; Steering Trim; RADIO SYSTEM CONTROLS
X O -1 • 15 TRAXXAS TQ i RADIO SYSTEM 5 Remember, always turn the TQi transmitter on first and off last to avoid damage to your model. Automatic Fail-Safe The TQi transmitter and receiver are equipped with an automatic fail-safe system that does not require user programming. In the event of signal l...
Page 16 - USING THE RADIO SYSTEM
16 • X O -1 TRAXXAS TQ i RADIO SYSTEM Using Reverse: While driving, push the throttle trigger forward to apply brakes. Once stopped, return the throttle trigger to neutral. Push the throttle trigger forward again to engage proportional reverse. USING THE RADIO SYSTEM The TQi Radio System has been pr...
Page 17 - Decreased Steering Sensitivity (Negative Exponential); SETTING UP THE ANTENNA; Do not bend or kink the antenna wire! See the sidebar
X O -1 • 17 TRAXXAS TQ i RADIO SYSTEM Steering Sensitivity (Exponential) The Multi-Function knob on the TQi transmitter has been programmed to control Steering Sensitivity (also known as exponential). The standard setting for Steering Sensitivity is “normal (zero exponential),” with the dial full le...
Page 18 - The switch on the speed control only shuts; 8 NiCD / NiMH 6s LiPo; ADJUSTING THE SPEED CONTROL
18 • X O -1 Refer to the included Castle Driver’s Ed Guide instruction manual for full speed control operation details. The Castle Creations Mamba Monster Extreme speed control should not need reprogramming with normal use. However, if you install a different radio system in your model, or change th...
Page 19 - Do Not Operate your model in Wet Conditions; DRIVING YOUR MODEL
X O -1 • 19 Now it’s time to have some fun! This section contains instructions on driving and making adjustments to your model. Before you go on, here are some important precautions to keep in mind. • Allow the model to cool for a few minutes between runs. This is particularly important when using h...
Page 20 - BASIC TUNING ADJUSTMENTS; Camber; ° negative camber each side; Loosen
20 • X O -1 Once you become familiar with driving your model, you might need to make adjustments for better driving performance Adjusting Gear Mesh Incorrect gear mesh is the most common cause of stripped spur gears. Gear mesh should be checked and adjusted anytime a gear is replaced, or if excessiv...
Page 21 - Remove the lower spring retainer and; Stock
X O -1 • 21 Use stiffer springs to reduce bottoming out the chassis, reduce body lean, control brake dive, and provide a firmer, more responsive feel. Increasing the spring rate will increase the responsiveness of the suspension. This may be beneficial in some conditions, but may make the car feel t...
Page 22 - Centering Your Servo; RECEIVER BOX: MAINTAINING A WATERTIGHT SEAL; Removing and Installing Radio Gear
22 • X O -1 3. Empty the used shock oil from the shock body. 4. Fill the shock with new silicone shock oil up to the top of the shock body. 5. Slowly move the piston up and down (always keeping it submerged in oil) to release the air bubbles. Let the shock sit for a few minutes to allow any remainin...
Page 23 - MAINTAINING YOUR MODEL; The following procedures should be taken very seriously.
X O -1 • 23 MAINTAINING YOUR MODEL Your model requires timely maintenance in order to stay in top running condition. The following procedures should be taken very seriously. Frequently inspect the vehicle for obvious damage or wear. Look for: 1. Cracked, bent, or damaged parts.2. Check the wheels an...
Page 25 - ADVANCED TUNING ADJUSTMENTS; CAMBER GAIN; Rear
X O -1 • 25 ADVANCED TUNING ADJUSTMENTS CAMBER GAIN Your model has provisions for adjusting the camber gain geometry of the front and rear suspension. “Camber gain” refers to an increase in camber angle as the suspension is compressed. The camber gain of the vehicle can be changed inside or outside ...
Page 26 - GEARING; TUNING THE SEALED GEAR DIFFERENTIALS; Note; Gearing Compatibility Chart:; Do not drive the model at lower speeds in a confined
26 • X O -1 ADVANCED TUNING ADJUSTMENTS GEARING Changing the gearing allows you to fine tune the speed of the model and control the temperatures of the battery packs and motor. Use a lower gear ratio (numerically larger) to reduce current draw and temperatures. Use a higher gear (numerically lower) ...
Page 27 - Refilling the differential:; Rear Differential Removal
X O -1 • 27 5. Remove the two 3x15mm button head screws from the differential cover and set the differential cover aside. 6. Remove the two screw pins that fasten the driveshafts to the differential output. 7. Installation is the reverse of above. Rear differential: 1. Remove the two 3x25mm counters...
Page 28 - EXPERTS ONLY: OPERATING THE XO-1 AT MAXIMUM SPEED; Before you unlock the power system and outfit your model; Installing the High-Speed Pinion; the Traxxas Link application (available in the; 00mph Splitter Installation
28 • X O -1 EXPERTS ONLY: OPERATING THE XO-1 AT MAXIMUM SPEED Now that you are familiar with the operation of the XO-1 in ‘out-of-the-box’ trim, it’s time to explore the upper limits of its performance capability. Before you unlock the power system and outfit your model for full-power operation, mak...
Page 29 - TQi Docking Base foam pad; iPod touch 3rd Generation; closed course
X O -1 • 29 2. Download and install the Traxxas Link application from the App Store.3. Open the Traxxas Link application and touch the Unlock icon. Follow the prompts to register your model. You will be asked to accept the terms of use and provide an e-mail address. Make certain you can access the a...
Page 30 - in the presence
30 • X O -1 OPERATING THE XO-1 AT MAXIMUM SPEED Closed Course Only! Location is the most important thing to consider when driving 100mph. Only drive the XO-1 at full speed on a closed course where there is no possibility for an animal, spectator or other person to wander into the path of the vehicle...
Page 31 - TQ
X O -1 • 31 The XO-1’s TQi transmitter is equipped with the new TQi Docking Base. This innovative accessory transforms your iPhone® or iPod touch® into a powerful tuning tool that equips your TQi with an intuitive, high-definition, full-color graphical user interface. Traxxas Link The powerful Traxx...
Page 32 - when the transmitter trigger is at neutral.; Throttle Trim Seek Mode
32 • X O -1 TQ i ADVANCED TUNING GUIDE LED Color / Pattern Name Notes Solid green Normal Driving Mode See page 15 for information on how to use your transmitter controls. Slow red (0.5 sec on / 0.5 sec off) Binding See page 16 for more information on binding. Flashing fast green (0.1 sec on / 0.15 s...
Page 33 - Enter Programming; MENU TREE
X O -1 • 33 TQ i ADVANCED TUNING GUIDE Press MENU to move through options. Press SET to select an option. Press MENU to move through options. Press SET to select an option. Press SET to select an option. Enter Programming Press and hold MENU for 3 seconds Steering Sensitivity (Expo) One Blink Red 1 ...
Page 34 - Restoring Factory Defaults; Model Lock; Press SET. The status LED will blink green in single-flash; : To unlock a memory, press SET twice at step 5. The LED will
34 • X O -1 TQ i ADVANCED TUNING GUIDE Starting Over: Restoring Factory Defaults When programming your 2.4GHz transmitter, you may feel the need to start over with a clean slate. Follow these simple steps to restore the factory settings:1. Turn transmitter off.2. Hold both MENU and SET.3. Turn trans...
Page 35 - MENU TREE FORMULAS
X O -1 • 35 TQ i ADVANCED TUNING GUIDE Set Multi-Function knob for STEERING SENSITIVITY (Expo) Press/hold MENU green LED blinks Press SET red LED blinks x 8 Press SET to confirm green LED blinks (x8) Press/hold MENU returns to driving mode Set Multi-Function knob for THROTTLE SENSITIVITY (Expo) Pres...
