Trane MUA-SVP01A-EN - Manual

Trane MUA-SVP01A-EN

Trane MUA-SVP01A-EN – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.

1 Page 1
2 Page 2
3 Page 3
4 Page 4
5 Page 5
6 Page 6
7 Page 7
8 Page 8
9 Page 9
10 Page 10
11 Page 11
12 Page 12
13 Page 13
14 Page 14
15 Page 15
16 Page 16
17 Page 17
18 Page 18
19 Page 19
20 Page 20
21 Page 21
22 Page 22
23 Page 23
24 Page 24
25 Page 25
26 Page 26
27 Page 27
28 Page 28
29 Page 29
30 Page 30
31 Page 31
32 Page 32
33 Page 33
34 Page 34
35 Page 35
36 Page 36
37 Page 37
38 Page 38
39 Page 39
40 Page 40
41 Page 41
42 Page 42
43 Page 43
44 Page 44
45 Page 45
46 Page 46
47 Page 47
48 Page 48
49 Page 49
50 Page 50
51 Page 51
52 Page 52
53 Page 53
54 Page 54
55 Page 55
56 Page 56
57 Page 57
58 Page 58
Page: / 58

Table of Contents:

  • Page 2 – Overview
  • Page 3 – Default settings
  • Page 5 – Contents
  • Page 6 – Thermostat Output Curve; Airflow Station Layout
  • Page 7 – UNIT OFF MODE; Unit Operating Modes
  • Page 9 – UNIT MANUAL MODE
  • Page 12 – Heating/Ventilating/Cooling Operating Modes; Heating Mode; General Burner Control
  • Page 14 – Ventilation Mode
  • Page 15 – Cooling Mode
  • Page 16 – Damper Control Modes; Manual Mode
  • Page 17 – Mixed Air Temperature Mode
  • Page 18 – Building Pressure Mode; See Minimum Ventilation.
  • Page 19 – Functions
  • Page 20 – User Configured PID Control; DIRECT ACTING
  • Page 22 – REVERSE ACTING; Direct acting
  • Page 23 – Reverse acting
  • Page 24 – Unit Resets
  • Page 25 – Clock Set
  • Page 26 – Critical Fault Codes; FAULT CODE: Low Discharge Temperature; Diagnostics
  • Page 29 – FAULT CODE: Safety Circuit Open
  • Page 30 – FAULT CODE:Burner Status; The controller has activated the burner enable output, but the
  • Page 31 – FAULT CODE: Burner Hand
  • Page 32 – FAULT CODE: Flame Failure; SOLUTION:Investigate flame relay
  • Page 33 – SOLUTION: If fan is running
  • Page 35 – FAULT CODE: Check Airflow Switches
  • Page 36 – FAULT CODE: Clogged Filter Switch; SOLUTION:If clogged filter switch is closing.
  • Page 37 – FAULT CODE:Energy Save Mode 1; SOLUTION:If setpoints are misadjusted
  • Page 38 – SOLUTION:If setpoints are not misadjusted; FAULT CODE:Energy Save Mode 2; SOLUTION: If OAT, RoomT or DAT are such that heat is required
  • Page 39 – FAULT CODE:Energy Save Mode 3
  • Page 40 – SOLUTION: If setpoints are misadjusted; FAULT CODE:Insufficient OA; SOLUTION:If heat is desired
  • Page 41 – SOLUTION:If less outside air is desired
  • Page 43 – Menu Selection Tree for BACview; UNIT MODES HOTKEY - 2; Damper Mode; Menu Selection; Menu selection tree for BACview
  • Page 44 – Status; SET POINTS HOTKEY - 3
  • Page 45 – STATUS MENU HOTKEY - 4; Alarm
  • Page 48 – FUEL SELECT HOTKEY - 9
  • Page 49 – Temperature in Degrees F; Typical 10,000 Ohm Thermistor Output Curve; esi
  • Page 50 – Airflow station layout
  • Page 51 – I/O Zone 583 Controller Specifications
  • Page 52 – OUTPUT ASSIGNMENTS - ANALOG
  • Page 53 – Typical Wiring Schematic; Non-recirculating with evap DFOA and DFIA model diagram
  • Page 55 – Figure 10. Recirculating DFOA and DFIA model diagrams
  • Page 56 – Figure 11. Recirculating DFOA and DFIA model diagram
Loading the manual

Controls Programming Guide

January 2007

MUA-SVP01A-EN

DFIA
DFOA

Direct-Fired Indoor and Outdoor Make-Up
Air Units

"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.

Summary

Page 2 - Overview

Overview © 2005 American Standard Inc. All rights reserved MUA-SVP01A-EN A glossary has been provided to assist the reader in understanding distinctive terms and phrases. These terms and phrases appear in italics. Trane's Digital Control System, AdaptAire, is designed to give the user the ultimate i...

Page 3 - Default settings

MUA-SVP01A-EN • Direct-Fired Indoor and Outdoor Units 3 NETWORKING AdaptAire is adaptable to a variety of different network architectures and protocols. Each controller has built-in protocol translation and can be configured for operation on ARCnet156 or EIA-485 communication networks. See Appendix ...

Page 5 - Contents

MUA-SVP01A-EN 5 NETWORKING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 ADAPTAIRE DEFAULT SETTINGS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Unit Operating Modes . . . . . . . . . . . . . . . . . . . . . . ....

Other Trane Models