Trane 4TXCB004DS3HCCV - Manual

Trane 4TXCB004DS3HCCV

Trane 4TXCB004DS3HCCV Heater – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.

1 Page 1
2 Page 2
3 Page 3
4 Page 4
5 Page 5
6 Page 6
7 Page 7
8 Page 8
9 Page 9
10 Page 10
Page: / 10

Table of Contents:

  • Page 2 – Installer’s Guide; This coil is pressurized with 8-12 psig of dry air. Do not; D. FURNACE IN UPFLOW POSITION; CAUTION; To prevent damage to pan, ensure Heat Shield is assembled; HORIZONTAL LEFT; Figure 3; Figure 4; Start; Figure 2
  • Page 3 – F. FURNACE IN HORIZONTAL RIGHT POSITION; Both the coil and furnace must be fully supported. Do not; Airflo; Figure 6; For S-Series furnaces, bend outlet flanges in; Ensure Heat Shield is secure; Figure 8; UPFLOW; Figure 7; For legacy upflow
  • Page 4 – G. FURNACE IN HORIZONTAL LEFT POSITION; Both the coil and furnace must be fully supported. Screws and; Screws and standoffs are for alignment only. Equipment; BACK TAB IS BENT; Figure 9; Channel
  • Page 5 – Do not unseal refrigerant tubing until ready to fit refriger; PAINTED AREAS OF THE UNIT MUST BE SHIELDED; Water blow-off could occur in certain installation; Coil; installed in upflow or horizontal left positions.
  • Page 6 – K. CONDENSATE DRAIN PIPING; A field fabricated trap is not required for proper drainage due to
  • Page 7 – Outline Drawing
  • Page 8 – Troubleshooting Indoor TXV / Cooling Mode
  • Page 10 – About Trane and American Standard Heating and Air Conditioning; ommitted to using environmentally conscious print practices.
Loading the manual
Page 1

Table of Contents

General .................................................................................1

Application Information ......................................................1

Recommendation ................................................................2

Furnace in Upflow Position

................................................2

Furnace in Downflow Position

...........................................2

Furnace in Horizontal Right Position

................................3

Furnace in Horizontal Left Position

...................................4

Maximum Airflow Setting (

CFM) .......................................5

Installing / Brazing Refrigerant Lines ................................5

Leak Check ..........................................................................5

Condensate Drain Piping

....................................................5

Cleaning the Coil .................................................................6

Outline Drawing

...................................................................7

Troubleshooting Indoor TXV / Cooling Mode ...................8

Installer’s Guide

ALL phases of this installation must comply with NATIONAL, STATE AND LOCAL CODES
IMPORTANT —

This Document is

customer property

and is to remain with this unit. Please return to service information pack

upon completion of work.

IMPORTANT:

Review your installation requirements. Check the table on

the outline drawing and note all dimensions for your coil

before beginning the installation.

Figure 1

18-AD42D1-1D-EN

Cased Aluminum "Convertible" Coil

Model:

4TXCB004DS3HCCV

4TXCD010DS3HCBV

4TXCD010DS3HCCV

NOTE:

OPTIONAL DOWNFLOW GASKET INSTALLATION: For

unusually humid applications that expect prolonged

operation above 70% RH, it is recommended to use the

BAYGSKT001A0 gasket kit to prevent water from forming

on the bottom of the drain pan and dripping into the

supply ductwork.

WARNING

!

This product can expose you to chemicals including

lead, which are known to the State of California to cause

cancer and birth defects or other reproductive harm. For

more information go to www. P65Warnings.

ca.gov

A. GENERAL

This coil is designed for use in combination with a heat pump or

cooling outdoor section using

R-410A REFRIGERANT

.

The 4TXC equipment has been evaluated in accordance with

the Code of Federal Regulations, Chapter XX, Part 3280 or the

equivalent. “Suitable for Mobile Home use” The height of the

Furnace, Coil and discharge duct work must be 7 ft. or less.
Inspect the coil for shipping damage. Notify the transportation

company immediately if the coil is damaged.

B. APPLICATION INFORMATION

1. FURNACE AND COIL

The coil MUST BE installed downstream (in the outlet air)

of the furnace.

2. INDOOR UNIT AIRFLOW

Indoor unit must provide the required airflow for the heat

pump or cooling combinations approved for this coil.

WARNING (Medium/high pressure)

Contains Refrigerant!

System contains oil and refrigerant under high pressure.

Recover refrigerant to relieve pressure before opening the

system. See unit nameplate for refrigerant type. Do not

use non-approved refrigerants, refrigerant substitutes, or

refrigerant additives.

Failure to follow proper procedures or the use of non-

approved refrigerants, substitutes, or refrigerant additives

could result in death, serious injury, or equipment damage.

WARNING

!

"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.

Was this manual helpful?

About this manual

Brand
Trane
Model
4TXCB004DS3HCCV
Document type
Manual
Category
Heater
Language(s)
English
Pages
10
Format
PDF

Summary

Page 2 - Installer’s Guide; This coil is pressurized with 8-12 psig of dry air. Do not; D. FURNACE IN UPFLOW POSITION; CAUTION; To prevent damage to pan, ensure Heat Shield is assembled; HORIZONTAL LEFT; Figure 3; Figure 4; Start; Figure 2

2 18-AD42D1-1D-EN Installer’s Guide C. RECOMMENDATION If a coil is part of the total system installation, use the Installer’s Guide packaged with the furnaces, outdoor sections, and thermostat for physically installing those components. CAUTION ! This coil is pressurized with 8-12 psig of dry air. D...

Page 3 - F. FURNACE IN HORIZONTAL RIGHT POSITION; Both the coil and furnace must be fully supported. Do not; Airflo; Figure 6; For S-Series furnaces, bend outlet flanges in; Ensure Heat Shield is secure; Figure 8; UPFLOW; Figure 7; For legacy upflow

18-AD42D1-1D-EN 3 Installer’s Guide F. FURNACE IN HORIZONTAL RIGHT POSITION Both the coil and furnace must be fully supported. Do not attempt to suspend the coil using the brackets.NOTE: When installing onto an S-Series furnaces in horizontal right or downflow configuration the flanges will be bent ...

Page 4 - G. FURNACE IN HORIZONTAL LEFT POSITION; Both the coil and furnace must be fully supported. Screws and; Screws and standoffs are for alignment only. Equipment; BACK TAB IS BENT; Figure 9; Channel

4 18-AD42D1-1D-EN Installer’s Guide G. FURNACE IN HORIZONTAL LEFT POSITION Both the coil and furnace must be fully supported. Screws and standoffs are provided for alignment only. Figure 11 AIRFLOW FURNACE DUCT SPLASH GUARD CASED COIL APEX OF COIL POINTS AWAY FROM FURNACE Figure 10 HORIZONTAL LEFT C...

Ask a question

Up to 3 photos. Max 5 MB each. Formats: JPG, JPEG, PNG, WebP.