Page 2 - Remember...; Contents
? For television operation queries, please ring the helpline… Remember… 2 Contents SETTING UP Safety precautions – Some do’s and don’ts for you to be aware of 3 Installation and important information 4 The remote control – an at-a-glance guide 5 Connecting external equipment – a guide to connecting ...
Page 3 - Safety Precautions; ABOVE ALL; Air Circulation
3 Safety Precautions This equipment has been designed and manufactured to meet international safety standards but, like anyelectrical equipment, care must be taken to obtain the best results and for safety to be assured. Please readthe points below for your own safety. They are of a general nature, ...
Page 4 - Installation and important information; Where to install; EXCLUSION CLAUSE
4 Installation and important information Where to install Locate the television away from direct sunlight and stronglights, soft, indirect lighting is recommended for comfortableviewing. Use curtains or blinds to prevent direct sunlightfalling on the screen. Place on a sturdy platform, the mounting ...
Page 5 - The remote control; UP; Inserting batteries and effective range of the remote
5 The remote control UP Simple at-a-glance reference of your remote control. Remove the back cover to reveal the battery compartment and make sure the batteries are insertedthe right way round. Suitable battery types for this remote are AAA, IEC R03 1.5V. Do not combine a used, old battery with a ne...
Page 6 - Connecting external equipment; media recorder
6 Connecting external equipment Before connecting any external equipment, turn off all main power switches. If there is no switchremove the mains plug from the wall socket. HDMI™ (High-Definition Multimedia Interface) is for usewith a DVD, decoder or electrical equipment with digitalaudio and video ...
Page 7 - Connecting a computer; the back of your television
7 Connecting a computer the back of your television Computer Audio cable for PC to television connection (not supplied) Conversion adaptor if required (not supplied) RGB PC cable (not supplied) Mini D-sub 15 pin connector Before connecting any external equipment, turn off all main power switches. If...
Page 8 - Controls and input connections; Switching on; Using the remote control
8 Controls and input connections If the RED LED is unlit check that the mains plug isconnected to the power supply. If the picture does notappear press i on the remote control, it may take a few moments. To put the television into Standby press i on the remote control, the GREEN active standby LED w...
Page 9 - Tuning the television for the first time; if they are connected
9 Tuning the television for the first time Before switching on the television put your decoder and media recorder to Standby if they are connected and ensure the aerial is connected. To set up the television use the buttons on the remote control as detailedon page 5. EXIT Cancel AUTO TUNING Progress...
Page 10 - Digital; auto tuning; Auto tuning
Use Q or P to move through the list to select a programme then press OK to view. At any time by pressing and holding B a list will appear on screen showing modes and allstored external equipment . Use P and Q to highlight and OK to select. 3 10 NOTE: As new services are broadcast it will be necessar...
Page 11 - when the television is switched back on.; manual tuning; Manual tuning
NOTE: When the television is switched off the mode being viewed at the time will automatically be selected when the television is switched back on. 11 Digital programme sorting, manual tuning With the list of stations now showing use Q or P to highlight the station you want to move and press R . The...
Page 12 - Tuning; Analogue; mode for the first time; Quick Setup
12 Tuning Analogue mode for the first time The Quick Setup feature will tune all analogue channels currently available in the area. To put the television into ATV mode press and hold B then use P or Q to highlight ATV . Press OK to select. Manual tuning Prog. Channel Station 1 C22 BBC1 2 C28 BBC2 3 ...
Page 13 - manual tune; The television can be tuned-in manually using; . For example: if the television cannot be; System
Manual tuning Prog. Channel Station 0 C60 1 C22 BBC1 2 C28 BBC2 3 C25 ITV 4 C32 CH4 5 C69 OK Select Sort MENU Back EXIT Watch TV 4 Press R to select System and use P or Q to change if required. Then press R to select Search . Press P or Q to begin the search. The search symbol will flash. 13 Analogu...
Page 14 - Using Auto tuning; LEASE
Using Auto tuning 1 2 3 4 5 To set up the television using Auto tuning , press MENU and use S or R to select the SET UP menu. You must allow the television to complete the search. When the search is complete the television willautomatically select programme position 1. This may notbe a clear picture...
Page 15 - sorting programme positions; Programme skip
Manual tuning Prog. Channel Station 0 C60 VCR 1 C22 BBC1 2 C28 BBC2 3 C25 ITV 4 C32 CH4 5 C69 OK Select Sort MENU Back EXIT Watch TV 15 Analogue programme skip, sorting programme positions Press MENU and repeat from Step 2 or press EXIT . Each programme position has to be individually selected. To t...
Page 16 - Volume
Press Q to highlight Bass , Treble or Balance and S or R to change the setting. When connecting to a Hi-fi unit, set the Speaker option to Off . Then select Fixed or Variable for the Monitor (Audio) in the AV connection menu. ( See 'Input selection and AV connections' section ). Bass, Treble and Bal...
Page 17 - Sound controls
SOUND Dual Dual 1 Bass 0 Treble 0 Balance 0 WOW OK Stable sound On MENU Back EXIT Watch TV 1/2 17 Sound controls continued, SRS WOW™ sound effects, dual, stable sound ® SRS WOW ™ sound effects SRS WOW™ is a suite of audio effects which use the stereo signals being broadcast to produce enhanced sound...
Page 18 - Widescreen viewing; SUPER LIVE 1; button repeatedly to select between; SUPER LIVE 2
SUBTITLE When subtitles are included on a letterbox format broadcast, this setting will raise the picture to ensure that all the text is displayed. SUBTITLE 18 Widescreen viewing SUPER LIVE 1 This setting will enlarge a 4:3 image to fit the screen by stretching the image horizontally and vertically,...
Page 19 - continued; WIDE; EXACT SCAN
19 Widescreen viewing continued 14:9 Use this setting when watching a 14:9 broadcast. Use this setting when watching a widescreen DVD, widescreen video tape or a 16:9 broadcast (when available). Due to the range of widescreen formats (16:9, 14:9, 20:9 etc.) black bars may be visible on the top and b...
Page 20 - Picture controls; Picture position –; only; Back light; PLEASE NOTE: features not available in
PICTURE Picture settings OK 3D Colour management Off Base colour adjustment Cinema mode Off MENU Back EXIT Watch TV 2/2 20 Picture controls To return to the original factory settings select Reset in the Picture position menu and press OK . Picture position – analogue only The picture position may be...
Page 21 - Colour temperature; DNR – Digital Noise Reduction; Picture preferences
In the Picture settings menu press Q until Colour Temperature is highlighted. Press S or R to select between Normal , Warm and Cool to suit your preference. 1 2 Colour Temperature increases the ‘warmth’ or ‘coolness’ of a picture by increasing the red or blue tint. Colour temperature Picture setting...
Page 22 - D Colour management; Cinema mode
1/2 SET UP Language English Country UK Auto tuning OK Manual tuning OK Antenna Amplifier On AV connection OK MENU Back EXIT Watch TV 22 Picture controls continued Press P and Q to select an option, then R to adjust the settings. 2 In the PICTURE menu press Q to select Base colour adjustment , then p...
Page 23 - Panel lock
From the FUNCTION menu select Panel lock and choose On or Off using S or R . Panel lock disables the buttons on the television. All buttons on the remote control can still be used. Panel lock 1 When Panel lock is On , a reminder will appear when the buttons on the television are pressed. If the stan...
Page 24 - The timers; Programme timer –
24 The timers Press Q to select the Sleep timer . Use the number buttons to set the required time. Forexample, to switch the television off in one and ahalf hours enter 01:30, or press S or R to increase/decrease in steps of 10 minutes. Press EXIT to finish. This feature will set the television to g...
Page 25 - on-screen information and; When viewing in; details for all available channels.; Information; Guide
25 Digital on-screen information and Programme Guide When viewing in digital mode, the on-screen information and programme guide give access to programme details for all available channels. The details of the programme will have beenadded to the screen. Press OK to save. 5 Information Select informa...
Page 26 - settings – parental control; Setting the PIN
26 Digital settings – parental control In order to prevent viewing of unsuitable films and programmes, channels and menus can be locked. Thesecan then only be accessed with a security code PIN when in digital mode. PARENTAL CONTROL Mode OFF Change Pin OK MENU Back EXIT Watch TV PARENTAL CONTROL Mode...
Page 27 - settings – favourite programmes,; Locking programmes
27 Digital settings – favourite programmes, locked programmes, encrypted programmes Locked Programmes stops the viewing of digital channels, they can only be accessed by entering the PIN. Locking programmes 1 From the FEATURE MENU press Q to select Favourite and Locked Programmes . Press R repeatedl...
Page 28 - settings; Audio languages
28 Digital settings continued – audio languages, subtitles, reset tv, common interface This feature allows a programme or film to be viewed with a choice of soundtrack language, provided they are currently being broadcast. Audio languages 1 From the SETUP MENU press Q to select Languages . This feat...
Page 29 - – software upgrade; Version; Searching for new software
29 Digital settings continued – software upgrade SOFTWARE UPGRADE Version 1.0 Auto upgrade ON Search for New Software OK 0 - 9 Enter PIN MENU Back EXIT Watch TV This feature can be used to check the version of software currently installed. Version If Auto upgrade is selected the software will automa...
Page 30 - Clock phase
30 PC settings – picture position, clock phase, sampling clock, reset 3 3 Use S or R to adjust until the picture clears. In the SET UP menu press Q until PC Setting is highlighted. Press OK to select, then Q to highlight Clock phase . Use S or R to adjust until the picture clears. 1 2 The Clock phas...
Page 31 - Input selection and; Input selection; INPUT signal selection
1/2 SET UP Language English Country UK Auto tuning OK Manual tuning OK Antenna Amplifier On AV connection OK MENU Back EXIT Watch TV Input selection and AV connections 31 Defining the INPUT and OUTPUT sockets so that the television recognises connected equipment. See page 6for a clear view of the ba...
Page 33 - text services – setting up,; Modes; Auto; will display; Fastext; will store your four favourite pages.; The; Navigating pages using Auto.; Navigating pages using LIST; Selecting modes
33 Analogue text services – setting up, general information, Auto and LIST modes This television has a multi-page text memory, which takes a few moments to load. It offers two Modes of viewing text – Auto will display Fastext , if available. LIST will store your four favourite pages. If Fastext is a...
Page 34 - text services – control buttons,; To hold a wanted page:; interactive services
Press T to access the index/initial page. The one displayed is dependant on the broadcaster. Remember to cancel te xt before changing channels – press the 6 / / 7 button twice. ☛ 34 Analogue text services – control buttons, Digital interactive services Below is a guide to the functions of the remote...
Page 35 - uestions; and; nswers
Below are the answers to some of the most common queries.For more information go to www.toshiba.co.uk A Check the mains switch is on and check all mainsconnections. Check the television is not in standby mode. Why is there no sound or picture? Q A Check the volume has not been turned down orthat sou...
Page 37 - Cleaning the screen and cabinet...; Disposal...
37 Q uestions and A nswers continued Cleaning the screen and cabinet… Turn off the power, clean the screen and cabinet with a soft, dry cloth. We recommend that you do not use any proprietary polishes or solvents on the screen or cabinet as this may cause damage. Disposal… The following information ...
Page 38 - Notes; For your own records
Page 40 - Specifications and accessories
Specifications and accessories Broadcast systems/channels PAL-I UHF UK21-UK69 PAL-B/G UHF E21-E69VHF E2-E12, S1-S41 SECAM-L UHF F21-F69VHF F1-F10, B-Q SECAM-D/K UHF R21-R69 VHF R1-R12 Video Input PAL, SECAM, NTSC 3.58/4.43 External connections EXT1 Input/Output 21-pin SCART RGB, A/VSelectable output...
