Page 2 - Copyright; to the use of the information contained herein.; Disclaimer; This manual has been validated and reviewed for accuracy. The
ii User’s Manual Copyright © 2008 by TOSHIBA Corporation. All rights reserved. Under the copyright laws, this manual cannot be reproduced in any form without the prior written permission of TOSHIBA. No patent liability is assumed, with respect to the use of the information contained herein. TOSHIBA ...
Page 3 - Trademarks; and Windows Vista are either registered trademarks; Safety Instructions
User’s Manual iii Trademarks Microsoft, Windows ® and Windows Vista are either registered trademarks or trademarks of Microsoft Corporation in the United States and/or other countries.DirectX, AcriveDesktop, DirectShow, and Windows Media are registerd trademarks of Microsoft Corporation.Intel, Intel...
Page 4 - When Using Your Computer
iv User’s Manual When Using Your Computer ■ Do not attempt to service the computer yourself. Always follow installation instructions closely. ■ Do not carry a battery in your pocket, purse, or other container where metal objects (such as car keys) could short-circuit the battery terminals. The resul...
Page 5 - FCC information; FCC notice “Declaration of Conformity Information”; modifications made to this equipment, not expressly approved by
User’s Manual v FCC information FCC notice “Declaration of Conformity Information” This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interfe...
Page 6 - EU Declaration of Conformity; provide, that changes or modifications not expressly approved by
vi User’s Manual BSMI notice (Taiwan only) EU Declaration of Conformity TOSHIBA declares that this product conforms to the following Standards: This product is carrying the CE-Mark in accordance with the related European Directives. Responsible for CE-Marking is TOSHIBA Europe, Hammfelddamm 8, 41460...
Page 7 - Modem warning notice; Conformity Statement
User’s Manual vii Modem warning notice Conformity Statement The equipment has been approved to [Council Decision 98/482/EC - "TBR 21"] for pan-European single terminal connection to the Public Switched Telephone Network (PSTN).However, due to differences between the individual PSTNs provided...
Page 8 - Japan regulations; Region selection
viii User’s Manual Japan regulations Region selection If you are using the computer in Japan, technical regulations described in the Telecommunications Business Law require that you select the Japan region mode. It is illegal to use the modem in Japan with any other selection. Redial Up to two redia...
Page 9 - Telephone company procedures; necessary to maintain uninterrupted service.; If problems arise; complaint with the FCC. In the event repairs are ever needed on your; Disconnection; complete the setup of your fax software before sending messages.
User’s Manual ix Telephone company procedures The goal of the telephone company is to provide you with the best service it can. In order to do this, it may occasionally be necessary for them to make changes in their equipment, operations, or procedures. If these changes might affect your service or ...
Page 10 - Instructions for IC CS-03 certified equipment; Users should not attempt to make such connections themselves, but
x User’s Manual Instructions for IC CS-03 certified equipment 1. The Industry Canada label identifies certified equipment. This certification means that the equipment meets certain telecommunications network protective, operational and safety requirements as prescribed in the appropriate Terminal Eq...
Page 11 - Notes for Users in Australia and New Zealand; is attached to the Australian PSTN would result in you modem being
User’s Manual xi Notes for Users in Australia and New Zealand Modem warning notice for Australia Modems connected to the Australian telecoms network must have a valid Austel permit. This modem has been designed to specifically configure to ensure compliance with Austel standards when the country/reg...
Page 12 - Notes for use of this device in New Zealand
xii User’s Manual Notes for use of this device in New Zealand ■ The grant of a Telepermit for a device in no way indicates Telecom acceptance of responsibility for the correct operation of that device under all operating conditions. In particular the higher speeds at which this modem is capable of o...
Page 13 - NOTE THAT FAULT CALLOUTS CAUSED BY ANY OF THE ABOVE; General conditions
User’s Manual xiii ■ When used in the Auto Answer mode, the S0 register must be set with a value of 3 or 4. This ensures: ■ a person calling your modem will hear a short burst of ringing before the modem answers. This confirms that the call has been successfully switched through the network. ■ calle...
Page 14 - Following information is only for EU-member states:
xiv User’s Manual The charge for a Telepermit assessment is $337.50. An additional charge of $337.50 is payable where an assessment is based on reports against non-Telecom New Zealand Specifications. $112.50 is charged for each variation when submitted at the same time as the original.An invoice for...
Page 15 - Optical disc drive safety instructions; The DVD Super Multi drive employs a laser system. To ensure proper
User’s Manual xv Visit http://www.energystar.gov or http://www.energystar.gov/power management for more information regarding the ENERGY STAR Program. Optical disc drive safety instructions Panasonic DVD Super Multi UJ-870B/870F Be sure to check the international precautions at the end of this secti...
Page 16 - Panasonic; DVD Super Multi DVR-KD08
xvi User’s Manual Panasonic DVD Super Multi DVR-KD08 ■ The DVD Super Multi drive employs a laser system. To ensure proper use of this product, please read this instruction manual carefully and retain for future reference. Should the unit ever require maintenance, contact an authorized service locati...
Page 17 - TOSHIBA SAMSUNG STORAGE TECHNOLOGY; x slim DVD Writable Drive TS-L632H
User’s Manual xvii TOSHIBA SAMSUNG STORAGE TECHNOLOGY 8x slim DVD Writable Drive TS-L632H ■ THIS DVD WRITABLE DRIVE EMPLOY A LASER SYSTEM TO ENSURE PROPER USE OF THIS PRODUCT, PLEASE READ THIS INSTRUCTION MANUAL CAREFULLY AND RETAINFOR FUTURE REFERENCE. SHOULD THE UNIT EVER REQUIRE MAINTENANCE, CONT...
Page 18 - TOSHIBA
xviii User’s Manual TOSHIBA HD DVD-ROM Drive SD-L802B ■ THIS DVD WRITABLE DRIVE EMPLOY A LASER SYSTEM TO ENSURE PROPER USE OF THIS PRODUCT, PLEASE READ THIS INSTRUCTION MANUAL CAREFULLY AND RETAINFOR FUTURE REFERENCE. SHOULD THE UNIT EVER REQUIRE MAINTENANCE, CONTACT AN AUTHORIZED SERVICE LOCATION-S...
Page 20 - International Precautions
xx User’s Manual International Precautions CAUTION: This appliance contains a laser system and is classified as a "CLASS 1 LASER PRODUCT." To use this model properly, read the instruction manual carefully and keep this manual for your future reference. In case of any trouble with this model,...
Page 22 - Important Notice; claims for damages and penalties.
xxii User’s Manual Important Notice Copyrighted works including, but not limited to music, video, computer program, databases are protected by copyright laws. Unless specifically permitted under applicable copyright laws, you cannot copy, modify, assign, transmit or otherwise dispose of any copyrigh...
Page 23 - General Precautions; Creating a computer-friendly environment; Instruction Manual for Safety and Comfort
User’s Manual xxiii General Precautions TOSHIBA computers are designed to optimize safety, minimize strain and withstand the rigors of portability. However, certain precautions should be observed to further reduce the risk of personal injury or damage to the computer.Be certain to read the general p...
Page 24 - Heat injury
xxiv User’s Manual Heat injury ■ Avoid prolonged physical contact with the computer. If the computer is used for long periods, its surface can become very warm. While the temperature will not feel hot to the touch, if you maintain physical contact with the computer for a long time, for example if yo...
Page 25 - Table of Contents; Preface; Introduction; The Grand Tour
User’s Manual xxv Table of Contents Preface Manual contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xxxiConventions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xxxii Abbreviations . . . . . . . . . . . . . . . . . ...
Page 26 - Getting Started; Operating Basics
xxvi User’s Manual About the HD DVD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-10Writable discs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-11CDs. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ....
Page 28 - The Keyboard; Windows; Power and Power-Up Modes
xxviii User’s Manual LAN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-37 LAN cable types . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-37Connecting LAN cable . . . . . . . . . . . . . . . . . . . . . . . ....
Page 29 - HW Setup; Optional Devices; Troubleshooting
User’s Manual xxix Chapter 7 HW Setup Accessing HW Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-1HW Setup Window . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-1 Chapter 8 Optional Devices ExpressCard Slot . . . . . . . . . . ...
Page 31 - Manual contents
User’s Manual xxxi Preface Congratulations on your purchase of the TOSHIBA Satellite M300/L310, Satellite Pro M300/L310 Series computer. This powerful notebook computer provides excellent expansion capability, including multimedia devices, and it is designed to provide years of reliable, high-perfor...
Page 32 - Conventions; Abbreviations; Enter
xxxii User’s Manual Preface Chapter 4, Operating Basics , includes instructions on using the following devices: TouchPad, Sound System, optical media drives, modem, wireless communication and LAN. It also provides tips on care of the computer, and CD/DVDs. Chapter 5, The Keyboard , describes special...
Page 33 - Key operation; Ctrl; Display; ABC; failure to follow instructions may cause data loss or damage your; Start
User’s Manual xxxiii Preface Key operation Some operations require you to simultaneously use two or more keys. We identify such operations by the key top symbols separated by a plus sign ( + ). For example, Ctrl + C means you must hold down Ctrl and at the same time press C . If three keys are used,...
Page 35 - Equipment checklist; Hardware; Check to make sure you have all the following items:
User’s Manual 1-1 Chapter 1 Introduction This chapter provides an equipment checklist, and it identifies the computer's features, options and accessories. Equipment checklist Carefully unpack your computer. Save the box and packing materials for future use. Hardware Check to make sure you have all t...
Page 36 - Software; If any of the items are missing or damaged, contact your dealer
1-2 User’s Manual Introduction Software Microsoft ® Windows Vista™ The following software is preinstalled: ■ Microsoft ® Windows Vista™ ■ Microsoft Internet Explorer ■ TOSHIBA Value Added Package ■ TOSHIBA Hardware Setup ■ TOSHIBA Supervisor Password ■ TOSHIBA Assist ■ TOSHIBA ConfigFree ■ TOSHIBA D...
Page 37 - Features; Processor; Chipset
User’s Manual 1-3 Introduction Features Please visit your region’s web site for the configuration details of the model that you have purchased. Processor Memory Built-in Depend on the model you purchased.Please visit your region’s website for the configuration details of the model that you have purc...
Page 38 - Power; Battery Pack; AC adaptor; Hard disk Disclaimer; The available optical media drives are described below.
1-4 User’s Manual Introduction Power Disks Battery Pack Your computer is powered by a rechargeable lithium-ion battery pack. RTC Battery The internal RTC battery backs up the Real Time Clock and calendar. AC Adaptor The universal AC adaptor provides power to the system and recharges the batteries wh...
Page 39 - DVD Super Multi; Some models are equipped with a full-size DVD
User’s Manual 1-5 Introduction DVD Super Multi drive (Supporting DVD±R DL) Some models are equipped with a full-size DVD Super Multi drive module that lets you record data to rewritable CD/DVDs as well as run either 12cm (4.72") or 8cm (3.15") CD/DVDs without using an adaptor. It reads DVD-R...
Page 42 - Keyboard; Display Controller and
1-8 User’s Manual Introduction Keyboard Pointing Device Ports Built-In 14.1" WXGA CSV with 1280 horizontal × 800 vertical pixels. Graphics Controller Graphics controller maximizes display performance. Refer to Display Controller and Modes section in Appendix B, Display Controller and Modes for m...
Page 43 - Slots
User’s Manual 1-9 Introduction Slots Multimedia ExpressCard Slot The ExpressCard slot that can accommodate two standard module formats; an ExpressCard/34 module and an ExpressCard/54 module. An ExpressCard module is a small add-in card technology based on the PCI Express and Universal Serial Bus (US...
Page 44 - Communications; Modem
1-10 User’s Manual Introduction Communications Modem The internal modem feature is not available on all models. Where present, it provides capability for data and fax communication. It supports V.90 (V.92). The speed of data transfer and fax communication depends on the analog telephone line conditi...
Page 45 - Security; Special features; Keypad overlay
User’s Manual 1-11 Introduction Security Special features The following features are either unique to TOSHIBA computers or are advanced features, which make the computer more convenient to use. Bluetooth Some computers in this series are equipped with Bluetooth functions. Bluetooth wireless technolo...
Page 46 - System Automatic; Turning off the power; Sleep Mode
1-12 User’s Manual Introduction HDD Automatic Power Off *1 This feature automatically cuts off power to the hard disc drive when it is not accessed for a specified time. Power is restored when the hard disc is accessed. This can be specified in the Power Options. System Automatic Sleep Mode/Hibernat...
Page 47 - TOSHIBA Value Added Package; Control Panel
User’s Manual 1-13 Introduction TOSHIBA Value Added Package This section describes the TOSHIBA Component features pre-installed on the computer. *1 Click , Control Panel , System and Maintenance , and then click Power Options . TOSHIBA Power Saver TOSHIBA Power Saver provides you with the features o...
Page 48 - Utilities and Applications
1-14 User’s Manual Introduction Utilities and Applications This section describes pre-installed utilities and tells how to start them. For details on operations, refer to each utility’s online manual, help files or readme.txt files. TOSHIBA Assist TOSHIBA Assist is a graphical user interface that pr...
Page 51 - Options; Memory expansion; Use only PC5300* compatible DDRII memory modules. See your; Battery pack
User’s Manual 1-17 Introduction Options You can add a number of options to make your computer even more powerful and convenient to use. Refer to Chapter 8 Optional Devices , for details. The following options are available: Memory expansion Two memory modules can be installed in this computer. Use o...
Page 53 - familiar with each component before you operate the computer.; Front with the display closed; Multiple Digital; MEMORY STICK, MEMORY STICK PRO and; Wireless; The Wireless Communication Switch turns on the
User’s Manual 2-1 Chapter 2 The Grand Tour This chapter identifies the various components of your computer. Become familiar with each component before you operate the computer. Front with the display closed The following figure shows the computer's front with its display panel in the closed position...
Page 55 - Left side; out of the vents as items such as pins or similar objects, which can
User’s Manual 2-3 The Grand Tour Left side The following figure shows the computer's left side. The left side of the computer Cooling Vents External Monitor Port Microphone Jack USB Ports Headphone ( S/P DIF ) Jack HDMI ExpressCard Slot i.LINK (IEEE1394a) Port External Monitor Port This 15-pin port ...
Page 56 - Right side
2-4 User’s Manual The Grand Tour Right side The following figure shows the computer's right side. The right side of the computer * The figure shows FM Antenna Jack. Universal Serial Bus (USB 2.0) ports Universal Serial Bus port which comply to the USB 2.0 standard, are provided. The ports with the i...
Page 57 - Backside; LAN Jack; Operating; Modem Jack; DC IN 19V Jack
User’s Manual 2-5 The Grand Tour Backside The following figure shows the computer's back panel. The backside of the computer LAN Jack This jack lets you connect to a LAN. The adaptor has built-in support for Ethernet LAN (10 megabits per second, 10BASE-T) and Fast Ethernet LAN (100 megabits per seco...
Page 58 - Underside; display is closed before turning over your computer.
2-6 User’s Manual The Grand Tour Underside The following figure shows the underside of the computer. Make sure the display is closed before turning over your computer. The underside of the computer Battery Pack Battery Release Latch Cooling Vents Battery Pack Lock Hard Disk Cover Memory Module and W...
Page 59 - Front with the display open; Speakers; Display Controller; Web Camera LED
User’s Manual 2-7 The Grand Tour Front with the display open This section shows the front of the computer with the display open. Refer to the appropriate illustration for details. To open the display, lift the front of the display. Position the display at a comfortable viewing angle. The front of th...
Page 61 - Optical Disc Drive; Region codes for DVD drive and media; Fingerprint Sensor
User’s Manual 2-9 The Grand Tour Optical Disc Drive An ATAPI interface controller is used for optical disc operation. When the computer is accessing a optical disc, an indicator on the drive glows. Region codes for DVD drive and media Optical disc drive and their associated media are manufactured ac...
Page 62 - About the HD DVD; Unfinalized DVDs created on home DVD recorders may not be
2-10 User’s Manual The Grand Tour About the HD DVD This section describes the features, use of HD DVD and HD DVD Media. Summary HD DVD allows users to enjoy video, concerts and other packaged content by taking advantage of its large amount of storage space and high-quality audio and video. HD DVD al...
Page 63 - Writable discs; CDs
User’s Manual 2-11 The Grand Tour ■ Dolby Digital audio enhancements are only supported by Microsoft ® Windows ® operating system. Content with high sample rates of 48kHz or more are downsampled when output through either the built-in speakers or headphone jack. ■ This device supports AACS (Advanced...
Page 64 - DVD Super Multi drive (Supporting DVD±R DL); without using an adaptor.; HD DVD ROM drive; The full-size HD DVD ROM drive module lets you record data to s as; DVD read; CD read; speed
2-12 User’s Manual The Grand Tour DVD Super Multi drive (Supporting DVD±R DL) The full-size DVD Super Multi drive module lets you record data to writable CD/DVDs as well as run either 12 cm (4.72") or 8 cm (3.15") CD/DVDs without using an adaptor. HD DVD ROM drive The full-size HD DVD ROM dr...
Page 66 - optional adaptor. Use of the wrong adaptor could damage your
2-14 User’s Manual The Grand Tour AC adaptor The AC adaptor converts AC power to DC power and reduces the voltage supplied to the computer. It can automatically adjust to any voltage from 100 to 240 volts and to a frequency of either 50 or 60 hertz, enabling you to use the computer in almost any cou...
Page 67 - Remote controller; Slim size remote controller; button
User’s Manual 2-15 The Grand Tour Remote controller A remote controller, which is provided with some models, enables you to perform some functions of your computer from a distant location.You can use your remote controller with Media Center to play CDs, DVDs and videos, to view pictures.The remote c...
Page 69 - Using the remote controller
User’s Manual 2-17 The Grand Tour Using the remote controller Some computers include a remote control unit, which allows you to control some of your computer’s functions from a distant location. Operational range of the remote controller Point the remote controller at your computer and press a butto...
Page 71 - Installing/Removing batteries; then install or remove the batteries as instructed.; Type of battery that can be used for the remote controller
User’s Manual 2-19 The Grand Tour Installing/Removing batteries Be sure to install the provided CR2016 type batteries before using the remote controller. The procedures for installing and removing the batteries vary depending on the type of the remote controller. Check the type and then install or r...
Page 72 - Installing the batteries; Open the battery cover on the back side of the remote controller.; Close the battery cover. Close the cover securely until it clicks.; Replacing the batteries; batteries and replace the discharged ones.
2-20 User’s Manual The Grand Tour Installing the batteries 1. Open the battery cover on the back side of the remote controller. Opening the battery cover 2. Be sure to place the batteries with correct polarities. Press the battery down to the stopper then push it forward to fit into the battery case...
Page 73 - fit into the battery case.; Placing slim size remote controller; Press gently to ensure a firm connection.; Remove a slim size remote controller
User’s Manual 2-21 The Grand Tour Slim size remote controller 1. Open the battery cover on the back side of the remote controller.2. Hold down the stopper and slide the battery out of battery case. Removing the batteries 3. Insert the battery in place. Be sure to place the batteries with correct pol...
Page 75 - Chapter 3; included with the computer, explains product liability.
User’s Manual 3-1 Chapter 3 Getting Started This chapter provides basic information to get you started using your computer. It covers the following topics: ■ Installing the battery pack ■ Connecting the AC adaptor ■ Opening the display ■ Turning on the power ■ Windows Vista™ setup ■ Turning off the ...
Page 76 - Installing the battery pack; To install a battery, follow the steps below.; The battery pack is a lithium ion battery, which can explode if not
3-2 User’s Manual Getting Started Installing the battery pack To install a battery, follow the steps below. 1. Turn the computer's power off. 2. Disconnect all cables connected to the computer. 3. Insert the battery pack. The Battery Release Latch clicks into place.4. Secure the Battery Pack Lock to...
Page 77 - Connecting the AC adaptor; to 240 volts and 50 or 60 hertz. For details on using the AC adaptor to
User’s Manual 3-3 Getting Started Connecting the AC adaptor Attach the AC adaptor when you need to charge the battery or you want to operate from AC power. It is also the fastest way to get started, because the battery pack will need to be charged before you can operate from battery power. The AC ad...
Page 78 - Connect the AC adaptor's DC output plug to the; Plug the power cord into a live wall outlet.; it vigorously or slamming it shut could damage the computer.
3-4 User’s Manual Getting Started 2. Connect the AC adaptor's DC output plug to the DC IN 19V jack on the back of the computer. Connecting the adaptor to the computer 3. Plug the power cord into a live wall outlet. Opening the display The display panel can be rotated in a wide range of angles for op...
Page 79 - This section describes how to turn on the power.; Windows VistaTM setup; Windows VistaTM Startup Screen Logo.
User’s Manual 3-5 Getting Started Turning on the power This section describes how to turn on the power. Press and hold the computer's power button for two or three seconds. Turning on the power Windows Vista™ setup When you first turn on the power, the computer's initial screen is the Microsoft ® Wi...
Page 80 - Shut Down; Disk LED and ODD
3-6 User’s Manual Getting Started Turning off the power The power can be turned off in one of the following modes: Shut down (Boot), Hibernation or Sleep Mode. Shut Down mode (Boot mode) When you turn off the power in Shut Down mode no data is saved and the computer will boot to the operating system...
Page 81 - Benefits of Sleep Mode
User’s Manual 3-7 Getting Started Benefits of Sleep Mode The Sleep Mode feature provides the following benefits: ■ Restores the previous working environment more rapidly than does Hibernation Mode. ■ Saves power by shutting down the system when the computer receives no input or hardware access for t...
Page 82 - Sleep Mode limitations; Hibernate; the contents of memory to the HDD. However, for safety sake, it is best
3-8 User’s Manual Getting Started Sleep Mode limitations Sleep Mode will not function under the following conditions: ■ Power is turned back on immediately after shutting down. ■ Memory circuits are exposed to static electricity or electrical noise. Hibernation Mode The hibernation feature saves the...
Page 83 - Automatic Hibernation Mode; Restarting the computer; to let all capacitors fully discharge.
User’s Manual 3-9 Getting Started Automatic Hibernation Mode The computer will enter Hibernation mode automatically when you press the power button or close the Display Screen. First, however, make the appropriate settings according to the steps below. 1. Open the Control Panel . 2. Open System and ...
Page 84 - System Recovery Options; Advanced Boot Options; menu will be displayed.; Repair Your Computer; and press; Create Optical Recovery Discs; VistaTM Business Edition and Ultimate Edition.
3-10 User’s Manual Getting Started System Recovery Options About 1.5GB hidden partition is allocated on the hard drive for the System Recovery Options. System Recovery Options The System Recovery Options feature is installed on the hard disk when shipped from the factory. The System Recovery Options...
Page 85 - Recovery Disc Creator; icon on the Windows Vista; Create; Restoring the preinstalled software from the; in a manner other than specified in the manual. Otherwise, space for
User’s Manual 3-11 Getting Started 3. Turn on your computer to open Windows Vista.4. Insert the (first) blank media into the tray of the Optical Drive.5. Double Click the Recovery Disc Creator icon on the Windows Vista desktop, or select the application from Start menu. 6. After TOSHIBA Recovery Dis...
Page 86 - Restoring the preinstalled software from Recovery; preinstalled software, follow the steps below.; appears, release the
3-12 User’s Manual Getting Started Restoring the preinstalled software from Recovery Media If the preinstalled files are damaged, use the Recovery Media you created, or HDD recovery to restore them. To restore the operating system and all preinstalled software, follow the steps below. 1. Load the Re...
Page 87 - and LAN. It also provides tips on caring for your computer.; Using the TouchPad; direction you want the on-screen pointer to go.; Two buttons below the keyboard are used like the buttons on a mouse
User’s Manual 4-1 Chapter 4 Operating Basics This chapter gives information on basic operations including using the TouchPad, optical media drives, sound system, modem, the wireless LAN and LAN. It also provides tips on caring for your computer. Using the TouchPad To use the TouchPad, simply touch a...
Page 88 - Using the fingerprint sensor; ball point pen against the TouchPad. The TouchPad could be damaged.
4-2 User’s Manual Operating Basics For some functions, you can tap the TouchPad instead of pressing a control button. Using the fingerprint sensor This product has a fingerprint utility installed for the purpose of enrolling and recognizing fingerprints. By enrolling the ID and password to the finge...
Page 89 - How to swipe the finger; the sensor and swipe finger levelly towards you.; Avoid swiping with the finger stiff or pressed-on too hard:
User’s Manual 4-3 Operating Basics How to swipe the finger Using the following steps when swiping fingers for fingerprint registration or authentication will help to minimize authentication failures:1. Align the first joint of the finger to the center of the sensor. Lightly touch the sensor and swip...
Page 90 - Points to note about the fingerprint sensor
4-4 User’s Manual Operating Basics Points to note about the fingerprint sensor Failure to follow these guidelines might result in (1) damage to the sensor or cause sensor failure, (2) finger recognition problems, or lower finger recognition success rate. ■ Do not scratch or poke the sensor with your...
Page 91 - How to delete the fingerprint data; TrueSuite Access; Fingerprint sensor limitations
User’s Manual 4-5 Operating Basics ■ The fingerprint for each finger is different and unique. Please ensure that only the registered or enrolled fingerprint or fingerprints are used for identification. ■ Check sliding position and speed. ■ Fingerprint data is enrolled up to 30~34. ■ Fingerprint data...
Page 92 - Points to note about the fingerprint utility; password. If the Windows logon password has not been setup, please
4-6 User’s Manual Operating Basics Points to note about the fingerprint utility ■ If Windows Vista™’s file encryption function EFS (Encryption File System) is used to encrypt a file, the file cannot be further encrypted using the encryption function of this software. ■ You can back up the fingerprin...
Page 93 - [We recommended enrolling at least two; OK; Windows logon via fingerprint authentication; Logon Authorization; Fingerprint system boot authentication; BACK SPACE; Please logon using the Windows logon password if the fingerprint
User’s Manual 4-7 Operating Basics 7. In case of finger injury or authentication failure, it is recommended that another fingerprint also be enrolled. The following message will be displayed: [We recommended enrolling at least two fingerprint images.] Click OK and repeat steps 3, 4, 5 and 6 with ano...
Page 94 - Next; Fingerprint Single Sign-On feature; It is necessary to register the User Password before using the
4-8 User’s Manual Operating Basics How to enable fingerprint system boot authentication settings It is necessary to first enroll your fingerprint with the TrueSuite Access Maganer application prior to enabling and configuring the fingerprint Pre- OS feature.Check that your fingerprint is enrolled be...
Page 95 - How to enable fingerprint Single Sign-On feature; Fingerprint utility limitations
User’s Manual 4-9 Operating Basics How to enable fingerprint Single Sign-On feature It is necessary to first enroll your fingerprint with the TrueSuite Access Maganer application prior to enabling and configuring the fingerprint Single Sign-On feature. Check that the fingerprint is enrolled before c...
Page 96 - How to enable/disable USB sleep and charge function; Refer to the
4-10 User’s Manual Operating Basics How to enable/disable USB sleep and charge function You can set enable/disable USB sleep and charge function in HW setup Refer to the USB Sleep and Charge function in Chapter 7 HW Setup . ■ The “USB Sleep and Charge function” only works for compatible ports. This ...
Page 97 - Using the Web Camera; and video images. The web camera will auto-run when Windows starts.; Using the software; The web camera software is pre-configured to start when you turn on
User’s Manual 4-11 Operating Basics Using the Web Camera This section describes the bundled webcam utility, which can capture still and video images. The web camera will auto-run when Windows starts. * Provided with some models Using the software The web camera software is pre-configured to start wh...
Page 99 - Using the microphone; Writing CD/DVD/HD DVD with the DVD Super Multi drive
User’s Manual 4-13 Operating Basics Using the microphone Your computer has a built-in microphone that can be used to record monaural sounds into your applications. It can also be used to issue voice commands to applications that support such functions.(Built-in microphone is provided with some model...
Page 100 - Loading discs
4-14 User’s Manual Operating Basics Loading discs To load a disc, follow the steps below and refer to the figures. 1. a. When the power is on, press the eject button to open the drawer slightly. Pressing the eject button Eject Button
Page 101 - b. Pressing the eject button will not open the drawer when the disc; Grasp the drawer gently and pull until it is fully opened.
User’s Manual 4-15 Operating Basics b. Pressing the eject button will not open the drawer when the disc drive's power is off. If the power is off, you can open the drawer by inserting a slender object (about 15 mm) such as a straightened paper clip into the eject hole just to the right of the eject ...
Page 102 - sure it lies flat, as shown in the figure above.
4-16 User’s Manual Operating Basics 3. Place the disc, label side up, in the drawer. Inserting a disc 4. Press gently at the centre of the disc until you feel it click into place. The disc should lie below the top of the spindle, flush with the spindle base. 5. Push the center of the drawer to close...
Page 103 - Removing discs; To remove the disc, follow the steps below and refer to the figure.
User’s Manual 4-17 Operating Basics Closing the disc drawer Removing discs To remove the disc, follow the steps below and refer to the figure. 1. To pop the drawer partially open, press the eject button. Gently pull the drawer out until it is fully opened. Do not press the eject button while the com...
Page 104 - Hold the disc gently by its edges and lift it out.; Writing CD/DVD/HD DVD with the DVD Super Multi; Ulead Movie factory for TOSHIBA.; Important message (DVD Super Multi drive supporting; you may fail to write or rewrite, lose data or incur other damage.
4-18 User’s Manual Operating Basics 2. The disc extends slightly over the sides of the drawer so you can hold it. Hold the disc gently by its edges and lift it out. Removing a disc 3. Push the centre of the drawer to close it. Press gently until it locks into place. Writing CD/DVD/HD DVD with the DV...
Page 105 - Before writing or rewriting; Based on TOSHIBA's limited compatibility testing, we suggest the; DVD Specifications for Recordable disc for
User’s Manual 4-19 Operating Basics Before writing or rewriting ■ Based on TOSHIBA's limited compatibility testing, we suggest the following manufacturers of CD-R/RW and DVD-R/+R/-RW/+RW/-RAM discs. However, in no event does TOSHIBA guarantee the operation, quality or performance of any disc. Disc q...
Page 106 - High Performance
4-20 User’s Manual Operating Basics ■ There are two types of DVD-R discs: authoring and general use discs. Do not use authoring discs. Only general use discs can be written to by a computer drive. ■ We can support only Format1 of DVD-R DL. Therefore you cannot do the additional writing. If your data...
Page 107 - When writing or rewriting
User’s Manual 4-21 Operating Basics When writing or rewriting Please observe/consider the following when you write or rewrite to a CD-R/ -RW, DVD-R/-RW/-RAM or DVD+R/+RW disc. ■ Do not perform any of the following actions when writing or rewriting: ■ Change users in the Windows ® Vista operating sys...
Page 108 - Important message
4-22 User’s Manual Operating Basics Writing CD/DVD/HD DVDs on HD DVD-RW drives You can use the HD DVD-RW drive to write data to either CD-R or CD-RW, DVD-R, DVD-R (Dual Layer), DVD-RW, DVD+R, DVD+R (Double Layer), DVD-RAM, HD DVD-R, HD DVD-R (Dual layer) discs. This computer is provided with TOSHIBA...
Page 109 - Legal Footnotes
User’s Manual 4-23 Operating Basics Legal Footnotes TOSHIBA does not bear responsibility for the following: ■ Damage to any CD-R, CD-RW, DVD-R, DVD-R (Dual Layer), DVD-RW, DVD+R, DVD+R (Double Layer), DVD+RW, DVD-RAM. HD DVD-R. HD DVD-R (Dual Layer) or HD DVD-RW disc that may be caused by writing or...
Page 113 - TOSHIBA Disc Creator
User’s Manual 4-27 Operating Basics TOSHIBA Disc Creator Note the following limitations when you use TOSHIBA Disc Creator: ■ DVD-Video cannot be created using TOSHIBA Disc Creator. ■ DVD-Audio cannot be created using TOSHIBA Disc Creator. ■ You cannot use TOSHIBA Disc Creator’s ‘Audio CD for Car or ...
Page 114 - Data Verification; When Using Ulead DVD MovieFactory for TOSHIBA; How to make a Labelflash DVD; Set PRINTING SIDE surface for underside.
4-28 User’s Manual Operating Basics ■ When you back up a DVD disc, be sure that the source drive supports recording to DVD-R, DVD-R (Dual Layer), DVD-RW, DVD+R, DVD+R (Double Layer) or DVD+RW media - if this is not the case then the source disc might not be backed up correctly. ■ When you back up a ...
Page 115 - How to make a DVD-Video; How to learn more about Ulead DVD MovieFactory
User’s Manual 4-29 Operating Basics How to make a DVD-Video Simplified steps for making a DVD-Video from video data captured from a DV-Camcorder: 1. Click Æ All Programs Æ DVD MovieFactory for TOSHIBA Æ Ulead DVD MovieFactory for TOSHIBA Launcher to launch DVD MovieFactory. 2. Insert a DVD-RW or DVD...
Page 116 - Important information for use
4-30 User’s Manual Operating Basics Important information for use Note the following limitations when you write Video DVD:1. Editing digital video ■ Log in with Administrator rights to use DVD MovieFactory. ■ Make sure that your computer is running on AC power when using DVD MovieFactory. ■ Operate ...
Page 117 - Media care; functions are supported.
User’s Manual 4-31 Operating Basics 3. About Straight to Disc ■ Not support to record on DVD-R/+R disc ■ Not support to record DVD+VR format by HDV ■ HDV support to burn DVD-Video only ■ DVD-VR format not support to add Menu 4. About recorded DVDs ■ Some DVD-ROM drives for personal computers or othe...
Page 118 - start; Properties menu; In case of a lightning storm, unplug the modem cable from the
4-32 User’s Manual Operating Basics Region selection Telecommunication regulations vary from one region to another, so you will need to make sure the internal modem's settings are correct for the region in which it will be used. To select a region, follow the steps below. 1. Click start , point to A...
Page 119 - Location list for region selection.; telephony location are incorrect.; Modem Selection; displayed. Select the COM port for your modem to use.; Dialing Properties; Select this item to display the dialing properties.; Connecting; To connect the modem cable, follow the steps below.
User’s Manual 4-33 Operating Basics Location list for region selection. A submenu appears displaying location information for telephony. Open dialog box, if the modem and Telephony Current Location region code do not match. A warning dialog box is displayed if current settings for region code and te...
Page 120 - Disconnecting; Do not pull on the cable or move the computer while the cable is
4-34 User’s Manual Operating Basics Connecting the internal modem Disconnecting To disconnect the internal modem cable, follow the steps below. 1. Pinch the lever on the connector in the telephone jack and pull out the connector. 2. In the same way, pull the cable’s other connector out of the comput...
Page 121 - Using the FM tuner; Select; to start FM software.; Wireless communications
User’s Manual 4-35 Operating Basics Using the FM tuner The availability of this feature is depending on the model you purchased.1. Plug the FM tuner antenna into the FM Antenna jack. Plug FM tuner antenna into the jack Select Start Æ All Programs Æ FM Tuner Utility to start FM software. Wireless com...
Page 122 - Wireless LAN
4-36 User’s Manual Operating Basics Wireless LAN The Wireless LAN feature is not available on all models. Where present, it supports the A,B, G and draft N standards but it is compatible with other LAN systems based on Direct Sequence Spread Spectrum/Orthogonal Frequency Division Multiplexing radio ...
Page 123 - Bluetooth Stack for Windows by TOSHIBA (depends on the; TOSHIBA notebook computers.
User’s Manual 4-37 Operating Basics Bluetooth Stack for Windows by TOSHIBA (depends on the model purchased) Please note that this software is specifically designed for the following operating systems: ■ Microsoft ® Windows Vista™ Detailed information regarding the use with these operating systems is...
Page 124 - LAN; LAN cable types; malfunction in LAN operation. Check with your LAN administrator
4-38 User’s Manual Operating Basics If you used the Task Bar to disable Wireless LAN, you will need to restart the computer to re-enable it. Alternatively, you can also follow this procedure:1. In the Control Panel , click System and Maintenance . 2. Click the Device Manager . The Device Manager win...
Page 125 - Disconnecting LAN cable; Cleaning the computer; The
User’s Manual 4-39 Operating Basics Connecting the LAN cable 3. Plug the other end of the cable into a LAN hub connector. Check with your LAN administrator before connecting to a hub. Disconnecting LAN cable To disconnect the LAN cable, follow the steps below. 1. Pinch the lever on the connector in ...
Page 126 - Moving the computer; HDD
4-40 User’s Manual Operating Basics Moving the computer The computer is designed for rugged durability. However, a few simple precautions taken when moving the computer will help ensure trouble-free operation. ■ Make sure all disk activity has ended before moving the computer. Check the HDD indicato...
Page 127 - Chapter 5; Typewriter keys; Caps Lock
User’s Manual 5-1 Chapter 5 The Keyboard The computer's keyboard layouts are compatible with a 101/102-key enhanced keyboard. By pressing some keys in combination, all the 101/ 102-key keyboard functions can be executed on the computer. The number of keys on your keyboard depends on which country/re...
Page 128 - Fn; Soft keys: Fn key combinations; Emulating keys on enhanced keyboard; settings are not restored by the Sleep Mode feature.
5-2 User’s Manual The Keyboard F1 ... F12 function keys The function keys (not to be confused with Fn ) are the 12 keys at the top of your keyboard. These keys function differently from other keys. F1 through F12 are called function keys because they execute programmed functions when pressed. Used i...
Page 129 - Hot keys
User’s Manual 5-3 The Keyboard Press Fn + F11 to access the integrated keypad. When activated, the keys with gray markings on the bottom edge become numeric keypad keys. Refer to the Keypad overlay section in this chapter for more information on how to operate these keys. The power on default for bo...
Page 131 - Fn Sticky key (Depends on the model you purchased); Before using Fn+1 and Fn+2, you must install the TOSHIBA Zooming
User’s Manual 5-5 The Keyboard TOSHIBA Zooming Utility (enlarge): Increases the icon size on the desktop or the font size within one of the supported application windows. Fn Sticky key (Depends on the model you purchased) You can use the TOSHIBA Accessibility Utility to make the Fn key sticky, that ...
Page 132 - Turning on the overlays
5-6 User’s Manual The Keyboard Keypad overlay Your computer's keyboard does not have an independent numeric keypad, but its numeric keypad overlay functions like one. The keys in the centre of the keyboard with gray letters make up the numeric keypad overlay. The overlay provides the same functions ...
Page 133 - Temporarily using normal keyboard (overlay on); Generating ASCII characters; Alt
User’s Manual 5-7 The Keyboard Temporarily using normal keyboard (overlay on) While using the overlay, you can temporarily access the normal keyboard without turning off the overlay: 1. Hold Fn and press any other key. All keys will operate as if the overlay were off. 2. Type upper-case characters b...
Page 135 - Power conditions; battery is installed and what the charge level is for the battery.
User’s Manual 6-1 Chapter 6 Power and Power-Up Modes The computer's power resources include the AC adaptor and internal batteries. This chapter gives details on making the most effective use of these resources including charging and changing batteries, tips for saving battery power, and power up mod...
Page 136 - Power indicators; Battery indicator; falls to a normal range, charge will resume. This occurs whether the
6-2 User’s Manual Power and Power-Up Modes Power indicators As shown in the above table, the Battery . Power indicators on the system indicator alert you to the computer’s operating capability and battery charge status. Battery indicator Check the Battery indicator to determine the status of the bat...
Page 137 - Power indicator; Battery types; Blinking orange
User’s Manual 6-3 Power and Power-Up Modes Power indicator Check the Power indicator to determine the power status: Battery types The computer has the following batteries: ■ Battery pack ( 3cell, 6cell, or 9cell depending on the model.) ■ Real Time Clock (RTC) battery Battery pack When the AC adapto...
Page 138 - Extending battery life; Real Time Clock battery
6-4 User’s Manual Power and Power-Up Modes Battery pack To ensure that the battery pack maintains its maximum capacity, operate the computer on battery power at least once a month until the battery pack is fully discharged. Refer to Extending battery life in this chapter for procedures. If the compu...
Page 139 - key - the BIOS setup screen will be displayed.; System Date; Press; key. BIOS setup will terminate and the computer will be
User’s Manual 6-5 Power and Power-Up Modes The charge in the RTC battery is getting low or has been exhausted. You will need to set the date and time within the BIOS setup using the following steps: 1. Press F2 key - the BIOS setup screen will be displayed. 2. Set the date in System Date . 3. Set th...
Page 140 - Care and use of the battery pack; Safety precautions
6-6 User’s Manual Power and Power-Up Modes Care and use of the battery pack The battery pack is a vital component of portable computing. Taking proper care of it will help ensure longer operating time on battery power as well as a longer life for your battery pack. Follow the instructions in this se...
Page 141 - Warning
User’s Manual 6-7 Power and Power-Up Modes 8. Never expose the battery pack to abnormal shock, vibration or pressure. The battery pack’s internal protective device will fail, causing it to overheat, explode, ignite or leak caustic liquids possibly resulting in death or serious injury. 9. Never let a...
Page 142 - Note; Procedures; Use only the computer connected to an AC power source to charge the
6-8 User’s Manual Power and Power-Up Modes 6. Be sure to monitor the remaining battery power. If the battery pack and real time clock battery discharge completely, Sleep Mode will not function and data in memory will be lost. Also, the computer might register an incorrect time and date. In this case...
Page 143 - Time; The charging time when the computer is on is affected by ambient
User’s Manual 6-9 Power and Power-Up Modes Time The following table shows the approximate time required to fully charge a discharged battery. Battery charging notice The battery may not charge right away under the following conditions: ■ The battery is extremely hot or cold. If the battery is extrem...
Page 144 - Monitoring battery capacity; operating time, based on the current power consumption rate and
6-10 User’s Manual Power and Power-Up Modes Monitoring battery capacity Remaining battery power can be monitored using the following methods. ■ Clicking the battery icon on the task bar ■ Via the Windows Mobility Center window Maximizing battery operating time A battery’s usefulness depends on how l...
Page 145 - Retaining data with power off
User’s Manual 6-11 Power and Power-Up Modes Retaining data with power off When you turn off your computer with fully charged batteries, the batteries retain data for the following approximate time periods. Extending battery life To maximize the life of your battery pack: ■ At least once a month, dis...
Page 146 - Replacing the battery pack; indicator flashes orange shortly after fully; Removing the battery pack; To replace a discharged battery, follow the steps below.; battery pack out of the computer.
6-12 User’s Manual Power and Power-Up Modes Replacing the battery pack When the battery pack reaches the end of its operating life you will need to install a new one. The life of the battery pack is generally about 500 recharges. If the Battery indicator flashes orange shortly after fully recharging...
Page 147 - Starting the computer by password
User’s Manual 6-13 Power and Power-Up Modes Installing the battery pack To install a battery, follow the steps below. 1. Turn the computer's power off. 2. Disconnect all cables connected to the computer. 3. Insert the battery pack. 4. Ensure the battery pack lock is moved into its locked position. S...
Page 148 - Fingerprint Power on; System Auto Off; Refer also to the sections
6-14 User’s Manual Power and Power-Up Modes or if availableSwipe your fingerprint on the sensor if you have already registered the fingerprint with the Fingerprint utility and enabled Fingerprint Power on Security . If you would not like to swipe your finger or cannot authenticate the fingerprint fo...
Page 149 - Chapter 7; Accessing HW Setup; General
User’s Manual 7-1 Chapter 7 HW Setup This chapter explains how to use TOSHIBA HW Setup program to configure your computer. TOSHIBA HW Setup lets you configure settings for General, Password, Display, Boot Priority, Keyboard, LAN, and USB. Accessing HW Setup To run HW Setup, click , All Programs , TO...
Page 150 - Password; Not Registered
7-2 User’s Manual HW Setup Password This tab allows you to set or reset the user password for power on. User Password Lets you register a new password or un-register an existing password. Owner String This blank field is used to display a message when the password field is displayed on startup. If a...
Page 151 - Enabled
User’s Manual 7-3 HW Setup Keyboard Wake-up on Keyboard When this feature is enabled and the computer is in Sleep Mode, you can turn on the computer by pressing any key. It is effective only for the internal keyboard and only when the computer is in Sleep Mode. USB USB Keyboard/Mouse/FDD Legacy Emul...
Page 153 - Power devices
User’s Manual 8-1 Chapter 8 Optional Devices Optional devices can expand the computer's capabilities and its versatility. This chapter describes connection or installation of the following devices, which are available from your TOSHIBA dealer: Cards/memory ■ ExpressCard ■ SD (Secure Digital) / SDHC ...
Page 154 - ExpressCard Slot; Inserting an ExpressCard; to make sure it is appropriate for your card.
8-2 User’s Manual Optional Devices ExpressCard Slot The computer is equipped with an ExpressCard slot that can accommodate one ExpressCard. Inserting an ExpressCard One ExpressCard connector is located on the left side of the computer.The computer's hot-install feature lets you install ExpressCard w...
Page 155 - Removing an ExpressCard; Safety Remove Hardware; icon on the Task Bar.; system services do not use the card.
User’s Manual 8-3 Optional Devices Removing an ExpressCard To remove the ExpressCard, follow the steps below.1. Click the Safety Remove Hardware icon on the Task Bar. 2. Click the ExpressCard you want to remove.3. Press the ExpressCard once to extend it.4. Grasp the extended ExpressCard, and remove ...
Page 156 - Card Type
8-4 User’s Manual Optional Devices SD/SDHC/MMC/MEMORY STICK / MEMORY STICK PRO/xD Memory cards The computer is equipped with a multiple digital media card slot that can accommodate SD/SDHC/MMC/MEMORY STICK/ MEMORY STICK PRO/ xD memory cards. These memory cards let you easily transfer data from devic...
Page 157 - Installing a memory card; Safely Remove Hardware; icon on the Taskbar.; Stop; button. A confirmation dialog may; Be sure the memory card is oriented properly before you insert it.
User’s Manual 8-5 Optional Devices Installing a memory card To install a memory card:1. Insert the memory card.2. Press gently to ensure a firm connection. Inserting a memory card Removing a memory card To remove a memory card, follow the steps below:1. Click the Safely Remove Hardware icon on the T...
Page 158 - Memory card care; Do not write to a memory card if the battery power is low. Low power
8-6 User’s Manual Optional Devices Memory card care 1. Do not write to a memory card if the battery power is low. Low power could affect writing accuracy. 2. Do not remove a memory card while read/write is in progress.3. The memory card is designed so that it can be inserted only one way. Do not try...
Page 159 - remove a memory module.; Installing a memory module
User’s Manual 8-7 Optional Devices Memory expansion You can install additional memory in the computer's memory module socket to increase the amount of RAM. This section describes how to install and remove a memory module. Installing a memory module Follow the steps below to install a memory module. ...
Page 160 - the computer's connectors at about a 45 degree angle. Press the
8-8 User’s Manual Optional Devices Removing the memory module cover 6. Lift one side of the insulator sheet and fit the module's connectors into the computer's connectors at about a 45 degree angle. Press the module carefully to ensure a firm connection. 7. Push the module down so it lies flat. Latc...
Page 161 - Up Modes; System; Points to note about memory module error; If you use the computer for a long time, the memory modules will
User’s Manual 8-9 Optional Devices 8. Seat the cover and secure it with the screws. 9. Replace the battery pack as described in Chapter 6, Power and Power- Up Modes . 10. Turn the power on and make sure the added memory is recognized. Open System in the Control Panel and click the General tab. Point...
Page 162 - Additional battery pack; Additional AC adaptor; reduce the weight and bulk of your carrying load.
8-10 User’s Manual Optional Devices Removing the memory module 6. Seat the cover and secure it with screws and replace the battery pack. Additional battery pack You can increase the portability of the computer with additional battery packs. If you’re away from an AC power source and your battery run...
Page 163 - External monitor; Display Controller and Modes; HDMI; monitors has not been confirmed, some HDMI monitors may not
User’s Manual 8-11 Optional Devices External monitor An external analog monitor can be connected to the external monitor port on the computer. The computer supports several video modes. Refer to Appendix B, Display Controller and Modes . To connect a monitor, follow the steps below. 1. Turn the comp...
Page 164 - Plug the other end of the HDMI cable into the HDMI out port on your; Setting for display video on HDMI; To view video on the HDMI device, be sure to configure the following; Settings for audio on HDMI; FN
8-12 User’s Manual Optional Devices 2. Plug the other end of the HDMI cable into the HDMI out port on your computer. Setting for display video on HDMI To view video on the HDMI device, be sure to configure the following settings otherwise you may find that nothing is displayed. Settings for audio on...
Page 165 - Precautions
User’s Manual 8-13 Optional Devices Precautions 1. Make a back-up of your data before transferring it to the computer. There is a possibility that the original data will be damaged. There is a particular risk that some frames will be deleted in the case of digital video transfer. TOSHIBA assumes no ...
Page 166 - Refer also to the documentation that came with your i.LINK device.
8-14 User’s Manual Optional Devices Disconnecting 1. Open the Safety Remove Hardware icon on the Task Bar. 2. Point to i.LINK (IEEE1394) device and click. 3. Disconnect the cable from the computer then from the i.LINK device. Security lock Security locks enable you to anchor your computer to a desk ...
Page 167 - go wrong can help prevent problems from occurring.; Problem solving process; may result in data loss or damage. You may destroy valuable problem
User’s Manual 9-1 Chapter 9 Troubleshooting TOSHIBA designed the computer for durability. However, should problems occur, following the procedures in this chapter can help to determine the cause. All readers should become familiar with this chapter. Knowing what might go wrong can help prevent probl...
Page 168 - Preliminary checklist
9-2 User’s Manual Troubleshooting Preliminary checklist Consider the simplest solution first. The items in this checklist are easy to fix and yet can cause what appears to be a serious problem. ■ Make sure you turn on all peripheral devices before you turn on the computer. This includes your printer...
Page 169 - Hardware and system checklist
User’s Manual 9-3 Troubleshooting Hardware and system checklist This section discusses problems caused by your computer's hardware or attached peripherals. Basic problems may occur in the following areas: System start-up When the computer does not start properly, check the following items: ■ Self Te...
Page 170 - Self test
9-4 User’s Manual Troubleshooting Self test When the computer starts up, the self test will be run automatically, and the following will be displayed: This message remains on the screen for a few seconds. If the self test is successful, the computer tries to load the operating system, depending on h...
Page 171 - AC power; Modes
User’s Manual 9-5 Troubleshooting AC power If you have trouble turning on the computer with the AC adaptor connected, check the Battery indicator. Refer to Chapter 6, Power and Power-Up Modes for more information. Battery If you suspect a problem with the battery, check the Battery indicator. For in...
Page 172 - Disposing of PC and PC batteries
9-6 User’s Manual Troubleshooting Disposing of PC and PC batteries ■ Discard this PC in accordance with applicable laws and regulations. For further information, contact your local government. ■ This PC contains rechargeable batteries. After repeated use, the batteries will finally lose their abilit...
Page 173 - Real Time Clock
User’s Manual 9-7 Troubleshooting ■ Reformatting the media ■ Reinstalling an operating system from the recovery CD-ROMThe procedures above delete only the initial part of the data used for file management. This makes the file invisible to the operating system, but the data can still be read by speci...
Page 174 - LCD panel; Problem
9-8 User’s Manual Troubleshooting LCD panel Apparent LCD problems may be related to the computer's setup. Hard disk drive Problem Procedure No display Press hot keys Fn + F5 to change the display priority, to make sure it is not set for an external monitor. Problems above remain unresolved or other ...
Page 175 - Recovery Discs
User’s Manual 9-9 Troubleshooting Recovery Discs DVD Super Multi drive (Supporting DVD±R DL) For more information, refer to Chapter 4, Operating Basics . Problem Procedure The following message appears when executing Recovery Disc Creator."The Recovery Disc Creator can not be launched because th...
Page 181 - Pointing device
User’s Manual 9-15 Troubleshooting Pointing device If you are using a USB mouse, also refer to the USB section in this chapter and to your mouse documentation. TouchPad Problem Procedure On-screen pointer does not respond to Pad operation The system might be busy. If the pointer is shaped as an hour...
Page 182 - USB mouse
9-16 User’s Manual Troubleshooting USB mouse USB Also refer to your USB device’s documentation. Problem Procedure On-screen pointer does not respond to mouse operation The system might be busy. If the pointer is shaped as an hourglass, wait for it to resume its normal shape and try again to move it....
Page 183 - USB Sleep and Charge function
User’s Manual 9-17 Troubleshooting USB Sleep and Charge function Problem Procedure I cannot use the “USB Sleep and Charge function”. The setting of “USB Sleep and Charge function” may be [Disabled]. Change the setting to [Enabled] in the HW Setup. When there is a current overflow of the external dev...
Page 184 - Sound system
9-18 User’s Manual Troubleshooting Memory expansion Refer also to Chapter 8, Optional Devices , for information on installing memory modules. Sound system Refer also to documentation for your audio devices. External devices connected to the compatible ports do not work when connected to a compatible...
Page 185 - Monitor
User’s Manual 9-19 Troubleshooting Monitor Refer also to Chapter 8, Optional Devices , and to your monitor’s documentation. Modem Problem Procedure No sound is heard Check the software volume settings. Make sure the headphone connection is secure. If problems persist, contact your dealer. Problem Pr...
Page 188 - TOSHIBA support; Before you call
9-22 User’s Manual Troubleshooting TOSHIBA support If you require any additional help using your computer or if you are having problems operating the computer, you may need to contact TOSHIBA for additional technical assistance. Before you call Some problems you experience may be related to software...
Page 191 - Appendix A; Specifications; Environmental Requirements; meters
User’s Manual A-1 Appendix A Specifications This appendix summarizes the computer's technical specifications. Environmental Requirements Power Requirements Built-in Modem Operating Non-operating Ambient temperature 5°C to 35°C -20°C to 60 °C Relative humidity 20% to 80% 10% to 90% Altitude (from sea...
Page 192 - duplex
A-2 User’s Manual Specifications Communication specifications Communication System Data: Full duplex Fax: Half duplex Communication protocol Data ITU-T-Rec (Former CCITT) BellFax: ITU-T-Rec (Former CCITT) V.21/V.22/V.22bis/V.32/ V.32bis/V.34/V.90/V.92103/212A V.17/V.29/V.27ter/V.21 ch2 Communication...
Page 195 - Appendix B; Display controller; most widely used industry standards.
User’s Manual B-1 Appendix B Display Controller and Modes Display controller The display controller interprets software commands into hardware commands that turn particular pels on or off.The controller is an advanced Video Graphics Array (VGA) that provides Super VGA (SVGA) and Extended Graphics Ar...
Page 196 - Video modes; CRT Display; Some of display mode might not be supported depending on the
B-2 User’s Manual Display Controller and Modes Video modes The computer supports video modes defined in the table below. If your application offers a selection of mode numbers that do not match the numbers on the table, select a mode based on, resolution, number of colors and refresh rates. 1. Only ...
Page 197 - Appendix C; Card Specifications; Mini PCI TypeIII
User’s Manual C-1 Appendix C Wireless LAN Card Specifications Form Factor Mini PCI TypeIII Compatibility ■ IEEE 802.11 Standard for Wireless LANs ■ Wi-Fi (Wireless Fidelity) certified by the Wi-Fi Alliance. The "Wi-Fi CERTIFIED" logo is a certification mark of the Wi-Fi Alliance. Network Ope...
Page 198 - Radio Characteristics; Modulation
C-2 User’s Manual Wireless LAN Radio Characteristics Radio Characteristics of Wireless LAN Cards may vary according to: ■ Country/region where the product was purchased ■ Type of product Wireless communication is often subject to local radio regulations. Although Wireless LAN wireless networking pro...
Page 199 - Supported Frequency Sub-bands; Approved Countries/Regions for use; Channel ID
User’s Manual C-3 Wireless LAN Supported Frequency Sub-bands Subject to the radio regulations that apply in the countries/regions, your Wireless LAN card may support a different set of 2.4 GHz channels. Consult your Authorized Wireless LAN or TOSHIBA Sales office for information about the radio regu...
Page 201 - Appendix D; AC Power Cord and Connectors; Certification agencies
User’s Manual D-1 Appendix D AC Power Cord and Connectors The power cord’s AC input plug must be compatible with the various international AC power outlets and the cord must meet the standards for the country/region in which it is used. All cords must meet the following specifications: Certification...
Page 202 - USA and Canada
D-2 User’s Manual AC Power Cord and Connectors In Europe, power cords must be VDE type, H05VVH2-F and two conductor. For the United States and Canada, plug configuration must be a 2-15P (250 V) or 1-15P (125 V) as designated in the U.S. National Electrical code handbook and the Canadian Electrical C...
Page 203 - Appendix E; CPU
User’s Manual E-1 Appendix E Legal Footnotes This chapter states the Legal Footnotes information applicable to TOSHIBA computers. In the text in this manual, *XX is used to show which Legal Footnotes description is related to TOSHIBA computers.Description(s) related to this computer are marked with ...
Page 205 - Battery Life
User’s Manual E-3 Legal Footnotes Battery Life Battery life may vary considerably depending on product model, configuration, applications, power management settings and features utilized, as well as the natural performance variations produced by the design of individual components. Published battery...
Page 206 - wireless LAN can reach may vary depending on surrounding; Copy Protection; prevent or limit recording or viewing of the media.; Images; All images are simulated for purposes of illustration.
E-4 User’s Manual Legal Footnotes Wireless LAN The transmission speed over the wireless LAN and the distance over which wireless LAN can reach may vary depending on surrounding electromagnetic environment, obstacles, access point design and configuration, and client design and software/hardware conf...
Page 207 - Glossary
User’s Manual Glossary-1 Glossary The terms in this glossary cover topics related to this manual. Alternate naming is included for reference. Abbreviations AACS: advanced access content system AC: Alternating current ACPI: Advanced Configuration and Power Interface AMT: Intel Active Management Techn...
Page 216 - numeric keypad overlay:
Glossary-10 User’s Manual Glossary non-system disk: A disk for storing programs and data that cannot be used to start the computer. Compare system disk. nonvolatile memory: Memory that is capable of permanently storing information. Turning the computer’s power off does not alter data stored in nonvo...
Page 221 - Index
User’s Manual Index-1 Index A AC adaptor, 1-4 additional, 1-17connecting, 3-3 ASCII characters, 5-7 B Battery charging, 6-8extending battery life, 6-11indicator, 6-1location, 2-6Monitoring capacity, 6-10real time clock, 1-4, 6-4safety precautions, 6-6save mode, 1-12types, 6-3 Battery pack, 1-4 addit...
Page 222 - emulating keys on
Index-2 User’s Manual Index K Keyboard, 1-8, 5-1 emulating keys on enhanced, 5-2 F1 ... F12 function keys, 5-2 hot keys, 5-3typewriter keys, 5-1Windows® special keys, 5-5 Keypad overlay, 1-11, 5-6 numeric mode, 5-6temporarily using normal keyboard (overlay on), 5-7 turning on the overlays, 5-6 L LAN...