Toro 79347 - User Manual

Setup Loose Parts Use the chart below to verify that all parts have been shipped. Procedure Description Qty. Use 1 No parts required – Prepare the machine. Weight 2 Channel plate 2 Plate 2 Tabbed plate 2 Bolt (3/8 x 2-1/2 inches) 4 2 Nut (3/8 inch) 4 Install the weights. 3 No parts required – Remove...

Procedure Description Qty. Use Upper tube 1 Screw (1/4 x 3/4 inches) 2 Washer (1/4 inch) 2 Locknut (1/4 inch) 2 17 Lower tube 1 Install the discharge tubes. 18 No parts required – Adjust the parking brake. 19 No parts required – Check the tire pressure. Determine the left and right sides of the mach...

2 Installing the Weight Kit Parts needed for this procedure: 2 Weight 2 Channel plate 2 Plate 2 Tabbed plate 4 Bolt (3/8 x 2-1/2 inches) 4 Nut (3/8 inch) Procedure 1. Use the bolts (3/8 x 2-1/2 inches) nuts (3/8 inch)to secure the plates to the weight ( Figure 4 ). g185955 Figure 4 1. Weight 4. Tabb...

10 Installing the Cross Brace Parts needed for this procedure: 1 Cross brace 4 Hex-head bolt (5/16 x 7/8 inch) 4 Flange nut (5/16 inch) Procedure 1. Use 2 hex-head bolts (5/16 x 7/8 inch) andflange nuts to secure the cross brace to the leftand right bagger support ( Figure 22 ). g276069 Figure 22 1....

13 Assembling the Hood Parts needed for this procedure: 1 Hood 1 Grass screen 2 Hairpin cotter Procedure Use the 2 hairpin cotters to secure the grass screento the hood ( Figure 26 ). g188636 Figure 26 1. Grass screen 3. Hairpin cotter 2. Hood 14 Installing the Hood Parts needed for this procedure: ...

15 Installing the Bags Parts needed for this procedure: 2 Bag Procedure Hook the bag over the pivot assembly ( Figure 28 ). g037980 Figure 28 1. Bag 2. Pivot assembly 16 Installing the Hitch Cover Parts needed for this procedure: 1 Hitch cover Procedure 1. Apply a lubricant to the nipple on the hitc...

16. Secure the tubes together with the nuts (1/4inch) as shown in Figure 33 . 17. Insert the upper discharge tube through the tubeseal in the hood. 18. Pull the upper tube out slightly so that the sealextends outward and over the blower assembly( Figure 31 ). 19. Use both latches to attach the lower...

Operation WARNING To avoid personal injury, do the following: • Become familiar with all operating andsafety instructions in the Operator's Manual for the mower before using this attachment. • Never remove the discharge tube, bags,bagger top, or the chute while the engineis running. • Always shut th...

Clearing Obstructions fromthe Bagger WARNING When the bagger is in operation, the bloweris rotating and can cut off or injure hands andfingers. • Before adjusting, cleaning, repairingand inspecting the blower, and beforeunclogging the chute, shut off the engineand wait for all moving parts to stop.R...

Operating Tips Tips for Bagging Remembering the Size of theMachine with the Attachment Remember that the machine is longer and wider withthis attachment installed. By turning too sharply inconfined places, you may damage the attachment. Trimming Always trim with the left side of the mower. Do not tr...

Maintenance Note: Determine the left and right sides of the machine from the normal operating position. Recommended Maintenance Schedule(s) Maintenance Service Interval Maintenance Procedure After the first 8 hours • Inspect the blower belt.• Inspect the bagger. After each use • Clean the hood scree...

Cleaning the Bagger andBags Service Interval: After each use 1. Wash the inside and outside of the bagger hood,bags, tube, and the underside of the mower. Note: Use a mild automotive detergent to remove dirt. 2. Make sure that you remove matted grass fromall parts. 3. After washing all parts, let th...

Storage Storing the BaggerAttachment 1. Clean the bagger attachment; refer to Cleaning the Bagger and Bags (page 28) . 2. Inspect the bagger attachment for damage; referto Inspecting the Bagger (page 28) . 3. Ensure that the grass bags are empty andthoroughly dry. 4. Store the bagger in a clean, dry...

Troubleshooting Problem Possible Cause Corrective Action 1. The cutting blade(s) are bent or unbalanced. 1. Install new cutting blade(s). 2. The blade-mounting bolt is loose. 2. Tighten the blade-mounting bolt. 3. There is a loose blower pulley or pulley assembly. 3. Tighten the appropriate pulley. ...

California Proposition 65 Warning Information What is this warning? You may see a product for sale that has a warning label like the following: WARNING: Cancer and Reproductive Harm—www.p65Warnings.ca.gov. What is Prop 65? Prop 65 applies to any company operating in California, selling products in C...