Toro 53454 - User Manual

Toro 53454

Toro 53454 – User Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.

1 Page 1
2 Page 2
3 Page 3
Page: / 3
Loading the manual

1

2

3

4

7

6

5

2 1

12:06

AM

0:10

PROGRAMMING IRRIGA TION DA

YS

1. Press . appears next to ‘days’

on the faceplate.

If you are programming the controller for the

first time, the display will initially read OFF .

2. Press . A will blink under ‘Su’

(Sunday)

on the display. Use to position the

under ‘Tu’ (T

uesday). Press . The under

Tu will become solid.

A new blinking drop will

appear under ‘W’. Use to position the

under ‘F’ (Friday). Press again.

1. P ARTS IDENTIFICA

TION

Hose-End Controller

1. Female swivel hose

thread faucet / tap adapter

2. Interior filter

3. T op

cover

4. Controller display

5. Programming and

operation buttons

6. Male hose

thread connection

7. Battery

compartment

53454

Bluetooth

Hose-End Timer

Installation & Operating

Instructions

2. BA TTER

Y INST

ALLA TION

1. Hold the controller with the battery

compartment facing you.

2. Remove the battery compartment cover.

3. Connect one 9V battery to the battery

connector.

4. Insert battery and replace battery cover.

Note: When changing the battery, make sure

the battery compartment stays dry.

Use alkaline

batteries

only .

3. CONTROLLER INST ALLA

TION

1. Make sure the filter (washer) is

in place.

2. Screw the controller to

the faucet / tap by

attaching the female

swivel hose-thread

connector (A) to the

faucet or hose-end.

Turn it clockwise

(hand-tighten only).

3. Connect the male

hose-thread connector

(B) to the hose.

4. IRRIGA TION PROGRAMMING

This section contains an example of a weekly

irrigation program. Simply alter start times

and run times to meet your irrigation

requirements.

The controller is programmed with 4 buttons:

Programming step – used to select the

appropriate programming mode (e.g., set clock).

Parameter selection – used to select the field

to be changed (e.g., hour, minute, etc.).

The field

to be changed must be blinking in order to have

its value changed.

Data increment (increase) – used to raise the

value of the selected field (e.g. add minute to run-time)

Data decrement (decrease) – used to lower the

alue of the selected field (e.g. reduce run-time by

a minute).

If no changes are implemented, the controller display

always reverts to the main screen (clock).

Display digits stop blinking after 40 seconds of

inactivity. If the last field stops blinking before you

have completed the programming process, press

to return to the process.

Emergency irrigation: After inserting batteries, if no

buttons are pressed, the clock will blink continuously.

After ten minutes, the controller will implement a

5-minute irrigation cycle every 24 hours.

SETTING CURRENT TIME & DA Y OF THE WEEK

Setting the Clock

T o enable the irrigation controller to operate the

irrigation system at desired times, the current time

and day of the week must be set as shown below:

1. Press several times until appears.

2. Press . The hour digits blink. Set the

current hour with the + and – buttons.

3. Press . The minute digits blink. Set the

current minute with the + and – buttons.

Setting the Day of the Week

1. Press until a blinking appears at the top

of the display.

2. Use and to select the correct day of

the week.

3. Press when done.

NOTE: To toggle between a 12-hour and

24-hour clock display, press the and

buttons simultaneously after the time has been

set.

PROGRAMMING A WEEKL

Y

IRRIGA TION SCHEDULE

(Set Days of the Week to Irrigate)

Let us assume that we want to irrigate three times

a day at 8am, 1pm, and 7pm, for ten minutes each

time on Tuesdays and Fridays.

SETTING DURATION OF IRRIGA

TION

1. Press until appears next to “duration”

on the faceplate.

2. Press . The hour digits will blink.

3. Use or to change the watering

duration in hours. For our example above,

that would be zero.

4. Press . The minutes digit will blink.

5. Use or to change the watering duration

in minutes. For our example above,

that would be ten.

time

53454

Su

ThF

Sa

M T u W

duration

days

manual

valve on

rain off

start

mode

set

Bluetooth

© 2018 The Toro Company

PN 373-0999 Rev. B

time

53454

Su

ThF

Sa

M T u W

duration

days

manual

valve on

rain off

start

Bluetooth

time

53454

Su

ThF

Sa

M T u W

duration

days

manual

valve on

rain off

start

Bluetooth

2 1

A

B

®

"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.

Other Toro Models

All Toro Other