Toro 140 2052 - User Manual
Toro 140 2052 – User Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 2 – Figure 1; Removing the Rail Guard; Figure 2; Figure 3
- Page 3 – Removing the Floor Pan Screw; Machines without MyRide Suspension System; Figure; Figure 6
- Page 6 – Installing the Assist Handle; Installing the Rail Guard; Secure the rail guard to the left frame rail (
- Page 7 – Secure the retainer to the pod (; Operation; Rotate the assist handle to the extend position
- Page 8 – Lower the assist handle as shown in; Stowing the Assist Handle; Rotate the assist handle to the stow; Lift the assist handle as show in
Form No. 3436-438 Rev A
Assist Bar Kit
TimeCutter
®
Riding Mower
Model No. 140-2052
Installation Instructions
Installation
Loose Parts
Use the chart below to verify that all parts have been shipped.
Description
Qty.
Use
No parts required
–
Prepare the machine.
Assist handle
1
Pin (grooved)
1
Washer—6 x 19 mm (3/8 x 3/4 inch)
1
Retaining ring
1
Assemble the assist handle.
Support spacer
1
Install the support spacer.
Assist handle bracket
1
Capscrew (1/4 x 4 inches)
1
Washer (1/4 x 5/8 inch)
1
Flange-head screw (thread forming—5/16 x
3/4 inch)
1
Flange locknut (1/4 inch)
1
Install the assist handle bracket.
Pin (grooved)
1
Washer—6 x 19 mm (3/8 x 3/4 inch)
1
Retaining ring
1
Install the assist handle.
No parts required
–
Install the rail guard.
Handle retainer
1
Shoulder screw (1/4 x 1-5/8 inch)
1
Install the handle retainer.
Preparing the Machine
1.
Moving the blade-control switch to the O
FF
position.
2.
Park the machine on a level surface.
3.
Move the motion control levers to the P
ARK
position.
4.
Move the throttle control to the F
AST
position.
5.
Shut off the engine.
Assembling the Assist
Handle
1.
Assemble the grooved pin through the hole in
the assist handle as shown in
.
© 2019—The Toro® Company
8111 Lyndale Avenue South
Bloomington, MN 55420
Register at www.Toro.com.
Original Instructions (EN)
Printed in the USA
All Rights Reserved
*3436-438* A
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Other Manuals for Toro 140 2052
Summary
g307205 Figure 1 1. Retaining ring 3. Washer—6 x 19 mm (3/8x 3/4 inch) 2. Pin (grooved) 4. Assist handle 2. Secure the pin to the handle with the washer—6x 19 mm (3/8 x 3/4 inch) and the retaining ring( Figure 1 ). Installing the SupportSpacer Removing the Rail Guard Machines with the MyRide Suspens...
g307206 g307210 Figure 3 1. Rail guard Removing the Floor Pan Screw Machines without MyRide Suspension System Remove the forward button-head screw that securesthe flange of the floor pan to the left frame rail ( Figure 4 ). g307223 Figure 4 1. Left frame rail 3. Button-head screw 2. Flange (floor pa...
Installing the Assist Handle 1. Align the lower hole in the assist handle withthe closed slot in the assist handle bracket asshown in Figure 11 . g307203 Figure 11 1. Assist handle 4. Retaining Ring 2. Assist handle bracket 5. Pin (grooved) 3. Washer—6 x 19 mm (3/8x 3/4 inch) 2. Assemble the grooved...
