Tesco FP11 - Manual

Slicing and Grating

Reassembly and Storage

Feed the food steadily into the appliance. DO NOT force the food:

Place the S blade (with the blade protector attached) on the drive shaft.

allow the blade to do the work. Too much force will overload the unit

The plate attachment can be placed in the bowl.

and may stall the motor.

Fit one blade to the plate holder. Place the other blade on top at right

If you are feeding in celery stalks for example, you may start with the

angles to the lower plate.

pusher out and then use the pusher to finish the process.

Attach the lid. Reassemble the pusher and feed tube and insert it in the

For larger slices, cut the food so that the pieces fit horizontally into the

funnel.

funnel and then use the pusher to complete the task.

Loosely coil the cable and store the unit in a dry cool cupboard out of

Do not run the appliance continuously for more than 2 minutes.

the reach of children and pets.

After extended use allow the unit to cool for 3 minutes before the
next use.

After Use

Turn the speed selector to the '0' position (OFF). Unplug the appliance
from the mains.

After Processing:

Remove the lid, the S blade, the feed tube and pusher. Disassemble the
pusher
Remove the bowl from the Motor Unit (turning the bowl anti-clockwise)
and empty the bowl.
Immerse all the above items in warm soapy water and clean them with
a damp cloth or soft brush. Rinse thoroughly and allow to dry.
Extreme caution must be taken when handling the blade as it is very
sharp. As soon as the blade is dry replace the protective cover.

Wipe the motor unit all over with a soft cloth dampened with soapy
water followed with a clean damp cloth. Ensure the interlock areas are
free of food particles. Dry well. Do not immerse the motor unit, mains
cable or plug in water.

After Slicing/Grating:

Remove the lid, the feed tube and pusher. Disassemble the pusher.
Lift out the plate holder.

Class II construction double insulated. This product must not

Remove the bowl from the Motor Unit (turning the bowl anti-clockwise)

be connected to earth.

and empty the bowl.
Remove the slicing/grating plate from the holder.
Immerse all the above items in warm soapy water and clean them with
a damp cloth or soft brush. Rinse thoroughly and allow to dry.
Extreme caution must be taken when handling the blade as it is very
sharp.
Wipe the motor unit all over with a soft cloth dampened with soapy
water followed with a clean damp cloth. Ensure the interlock areas are
free of food particles. Dry well. Do not immerse the motor unit, mains
cable or plug in water.

If your appliance suddenly stops

Switch the selector to ‘0' (off). Unplug the unit and wait fot 15 minutes
until the unit has completely cooled down. Reconnect the power and
resume using the appliance,.

Warranty

Your appliance is covered by a warranty for 12 months from the date of
purchase. If a fault develops during this period, please return the unit
to your nearest Tesco store together with the original receipt as proof of
purchase. This warranty in no way affects your consumer rights.

Specification

Power:

220-240 VAC 50Hz, 550W

SPL:

<85dbA

Duty Cycle:

3 min max.

Weight:

3.2Kg

Recommended Operating Times and Speeds

FP11 Food Processor User Guide

UK: Waste electrical products should not be disposed of
with household waste. Separate disposal facilities exist, for
your nearest facilities see www.recycle-more.co.uk or in-
store for details.
ROI: Produced after 13th August 2005. Waste electrical
products should not be disposed of with household waste.
Please recycle where facilities exist. Check with your Local
Authority or retailer for recycling advice.

Page 5

Food Processor

USER GUIDE

FP11

Tesco Stores Ltd, Delamare Road,
Cheshunt, Herts, EN8 9SL

Assembling your processor for slicing or grating

A

A:

Ensure the appliance is disconnected from the mains.

Place the unit on a solid level surface and hold it securely.

Place the bowl on the motor base and and then turn the bowl
clockwise until it is locked onto the motor base. The ‘LOCK’
mark on the bowl should align with the arrow on the base,

B:

Place the plate shaft onto the motor shaft and check it is

secure.

Do not place ingredients into the bowl. Wait until the lid is
in place and then insert the ingredients through the funnel
in the lid.

C:

Place the prepared plate onto the attachment and check it

is secure.

D:

Place the lid on the bowl. Locate the lug to the left of the slot in the motor

unit. Turn the lid clockwise (to the right) and lock it firmly into position.

Insert the feed tube and pusher into the funnel if needed

3

Meat, Vegetables
Cheese, Chocolate

Pulse operation gives control over texture

700g

Chopping

Pulse

‘S’ Blade

30 sec. bursts

Meat, Vegetables
Cheese, Chocolate

Increase time for finer texture.

700g

Chopping

1

‘S’ Blade

30 sec.

Soups, Drinks, etc

700g

Blending

1

‘S’ Blade

20 sec.

Cooked vegetables,
potatoes, fruit

700g

Purees

1;2

‘S’ Blade

10-15 sec.

Vegetables, cheese
potatoes, fruit

Slicing

2;3

Slicing Plate

Vegetables, cheese
fruit, chocolate.

Shredding

2;3

Shredding Plate

FOOD

COMMENT

MAX. QTY

FUNCTION

SPEED

TOOL

TIME

Food Preparation

Operation

Hints and tips

The appliance has three speeds, 1-3 (low-med-high) and pulse mode.

This appliance is not suitable for chopping hard items such as ice

1. The metal blade can be used for

cubes or frozen produce.

chopping meat, fish vegetables

Remove all bones from meat, stones from fruit, etc. Cut the food into

cheese etc. setting the speed to

suitable small pieces (25mm, 1" for hard foods and meat.)

maximum.

The maximum quantity of food you can process at any one time should

2. For finer chopping increase the

not exceed 700g for soft items and 600g for nuts and other items.

length of time you process.

We suggest you keep the liquid content of food to be processed to a

3. For coarse chopping, use the

minimum as excess liquid can penetrate the motor.

pulse button for a few seconds and

Items for processing can be placed in the bowl before attaching the lid

monitor the texture.

or introduced via the funnel after assembly.

For pulse operation, move the

Items for slicing should be cut into pieces which can fit into the funnel. If

selector to ‘P’ and hold it. This

you are using the feed tube these will need to be smaller than if you are

processes food at very high speed

using the funnel alone.

so only use pulse mode in very
short repeated bursts.

Refer to the table on the next page for advice on which speed to use for

Assemble the appliance. Make sure the selector is switched to ‘0' (off).

best results.

Plug the unit into the mains supply and switch on at the mains.

It may be necessary with some foods to stop the unit, and re-distribute
the food before continuing. Always switch the selector to ‘0' and
unplug the appliance before removing the lid.

B

C

D