Telex NI-223 Plus - Manual - manualsarea.com

Page 2 - NI223Plus - 3 -; Panel; plus; Plus; Table of Figures; plus

NI223Plus - 3 - Table of Contents 1 General ................................................................................... 4 2 Front and Rear Panel Connections and Indicators ............ 4 2.1 Front Panel LED ........................................................................................

Page 3 - General; Front and Rear Panel Connections and Indicators; Green LED indicates power to the NI223; Rear Panel Connectors; Pin

- 4 - NI223Plus 1 General The NI223 plus is an iDen® interface product designed to connect the IP-223 Ethernet Adapter Panel to the iDen® network. The iDen® Radio Interface can be used to make Direct Connect, Group Call, Alert Calls or Emergency Group calls over the iDen® network. The IP-223 and the...

Page 4 - NI223Plus - 5 -; Setup; Jumper Position; Web Page Configuration; Note

NI223Plus - 5 - 3 IP-223/NI223 plus Setup 3.1 IP-223 Setup 3.1.1 Jumper Settings Jumper Position Connection Type “A” Single Ended Tx/Rx Audio Line 1: J3, J9, J11, J16, J21 Line 2: J19, J20, J25, J28, J29 “A” 600 Ohm Rx Termination Line 1: J14 Line 2: J24 “B” Serial Port Communications Jumpers (TTL) ...

Page 5 - Type; ” column is a drop down; iDen Number; ” column holds the iDen® Radio Direct Connect and Group

- 6 - NI223Plus listening consoles. Configuration of the ring multicast and port numbers must be unique and consistent with the IP-223 and any listening console. For console configurations, please refer to the specific User Manual for that product. After the iDen® Radio Mode has been set, the IP-223...

Page 6 - NI223Plus - 7 -; IDen® Radio Setup; iDen

NI223Plus - 7 - 3.2 Connecting the IP-223 and the NI223 plus Figure 3 Connections between IP-223 and NI223 plus Connect the IP-223 and the NI223 plus to the iDen® radio as shown in Figure 3. The power for the NI223 plus will be obtained from the same power connector the IP-223 is using. Make sure th...

Page 7 - Setup IP Multicast List; Set Global Parameters

- 8 - NI223Plus 3.4 C-Soft Setup Note This example shows a basic setup for C-Soft. Please refer to the User manual for other Vega IP based consoles if necessary . 3.4.1 Setup IP Multicast List Figure 4 Setup IP Multicast List – iDen® Radio in Phone Mode operation Figure 4 shows an example of setting...

Page 8 - NI223Plus - 9 -; C-Soft Phone Control Buttons; IDen® Network Calling; Console Selected Calling

NI223Plus - 9 - 3.4.3 C-Soft Phone Control Buttons Figure 6 C-Soft Phone Control Buttons Setup Figure 6 shows a few of the basic C-Soft Phone Control buttons. Any button can be configured for a task by Right-Clicking on the button, then using the UI Element Function pull down menu. In this case, Pho...

Page 9 - Audio Alignment Procedure; Transmit Audio Alignment

- 10 - NI223Plus 4.2.1 A-Key, Alert The ‘A’ key is used to send an Alert function over the iDen® system. Using the standard dialing keys, enter the ID of the radio. Press the “A” key to send the alert. 4.2.2 B-Key, Send The “B” key is used as a send button when placing a manually dialed phone call. ...

Page 10 - NI223Plus - 11 -; Receive Audio Alignment

NI223Plus - 11 - 5.1.2 Receive Audio Alignment The standard Receive audio alignment procedures should be followed for the NI223 Plus installation. With AGC turned OFF, inject a 0dBm test tone into the IP-223 front end and measure the level at the Receive audio test points for line 1 or 2. (TP13 or T...

Page 11 - Cable Assembly

- 12 - NI223Plus 6 Cable Assembly 9 17 15 11 8 20 2 18 5 4 6 10 2 1 1 3 7 12 P1 P2 P3 P4 P5 19 P6 UNDERS ID E W IRING T ABL E CA BLE No . 1 CA BLE No . 2 CA BLE No . 3 CA BLE No . 4 21 CAB LE N o. 5 22 16 2 9 6 9 A 13 DET AIL A SC AL E 1 : 1 6 14 PI N TO PI N C OLOR CA BLE No. P1 -1 - P4 -1 R ED 3 P...

Page 12 - NI223Plus - 13 -; Factory Service Center; TELEX Communications, Inc; Vega Signaling Products; Visit our web site at

NI223Plus - 13 - 7 Warranty, Service, Repair, and Comments Important! Be sure the exact return address and a description of the problem or work to be done are enclosed with your equipment. Warranty (Limited) All Telex Communications, Inc. manufactured Vega Signaling products are guaranteed against m...

Page 13 - Specifications; Operating Temperature Range:; Front Panel Indicators:; Rear Panel Connections:

- 14 - NI223Plus 8 NI223 Plus Specifications Operating Temperature Range: • 0 to 55 ° C for full specifications Power Requirements: • +12 to +16 VDC, semi-regulated, 1A Max. Dimensions: • 2 ¾ ” W x 4 ¾ ” D x 1 ¾ ” H Front Panel Indicators: • Green LED Power Indicator Rear Panel Connections: • DB25 •...

Telex NI-223 Plus - Manual

Table of Contents:

Summary

Other Telex Models